Endress+Hauser Cerabar M PMC51? Cerabar M PMP51 User manual

BA385P/00/EN/10.09
71102503
Valid from software version:
01.00.zz
Operating Instructions
Cerabar M PMC51, PMP51, PMP55
Process pressure measurement

Overview of documentation Cerabar M Analog
2Endress+Hauser
Overview of documentation
Content Remarks
Technical Information TI436P Technical data
– The documentation can be found on the
documentation CD.
– The documentation is also available on the
Internet.
See: www.endress.com Download
Operating Instructions BA385P – Identification
– Installation
– Wiring
– Operation
– Commissioning
–Examplesof
configuration
– Description of
parameters
– Maintenance
– Troubleshooting
– Appendix
Brief Operating
Instructions
KA1036P – Installation
– Wiring
– Local operation
– Commissioning
– The documentation is supplied with the device.
– The documentation can also be found on the
documentation CD supplied.
– The documentation is also available on the
Internet.
See: www.endress.com Download

Cerabar M Analog Table of contents
Endress+Hauser 3
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 4
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Installation, commissioning and operation . . . . . . . . 4
1.3 Operational and process safety . . . . . . . . . . . . . . . . . 4
1.4 Notes on safety conventions and icons . . . . . . . . . . . 5
2 Identification . . . . . . . . . . . . . . . . . . . . 6
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 CE mark, Declaration of Conformity . . . . . . . . . . . . 8
2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 8
3 Installation . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Incoming acceptance and storage . . . . . . . . . . . . . . . 9
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Installation instructions . . . . . . . . . . . . . . . . . . . . . 10
3.4 Closing the cover . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.5 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 17
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 18
4.1 Connecting the device . . . . . . . . . . . . . . . . . . . . . . 18
4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 20
4.3 Potential equalization . . . . . . . . . . . . . . . . . . . . . . 21
4.4 Overvoltage protection (optional) . . . . . . . . . . . . . . 21
4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 23
5 Operation . . . . . . . . . . . . . . . . . . . . . . 24
5.1 Position of operating elements . . . . . . . . . . . . . . . . 24
5.2 Using the device display (optional) . . . . . . . . . . . . . 25
6 Commissioning. . . . . . . . . . . . . . . . . . 27
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.2 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7 Maintenance. . . . . . . . . . . . . . . . . . . . 28
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8 Troubleshooting . . . . . . . . . . . . . . . . . 29
8.1 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.2 Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.3 Response of output to errors . . . . . . . . . . . . . . . . . 29
8.4 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.5 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.6 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.7 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.8 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . 31
9 Technical data . . . . . . . . . . . . . . . . . . . 32
10 Appendix. . . . . . . . . . . . . . . . . . . . . . . 33
10.1 Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Safety instructions Cerabar M Analog
4Endress+Hauser
1 Safety instructions
1.1 Designated use
The Cerabar M is a pressure transmitter for measuring pressure and level.
The manufacturer accepts no liability for damages resulting from incorrect use or use other than that
designated.
1.2 Installation, commissioning and operation
The device is designed to meet state-of-the-art safety requirements and complies with applicable
standards and EU regulations. If used incorrectly or for applications for which it is not intended,
however, it can be a source of application-related danger, e.g. product overflow due to incorrect
installation or configuration. For this reason, installation, connection to the electricity supply,
commissioning, operation and maintenance of the measuring system must only be carried out by
trained, qualified specialists authorized to perform such work by the facility's owner-operator. The
specialist staff must have read and understood these Operating Instructions and must follow the
instructions they contain. Modifications and repairs to the devices are permissible only if they are
expressly approved in the Operating Instructions. Pay particular attention to the technical data and
information on the nameplate.
1.3 Operational and process safety
Alternative monitoring measures have to be taken while configuring, testing or servicing the device
to ensure the operational and process safety.
#Warning!
Dismantle device only when depressurized!

Cerabar M Analog Safety instructions
Endress+Hauser 5
1.4 Notes on safety conventions and icons
In order to highlight safety-relevant or alternative operating procedures in the manual, the following
conventions have been used, each indicated by a corresponding icon in the margin.
Symbol Meaning
#Warning!
A warning highlights actions or procedures which, if not performed correctly, will lead to serious
personal injury, a safety hazard or the destruction of the device.
"Caution!
Caution highlights actions or procedures which, if not performed correctly, can lead to personal
injury or the incorrect operation of the device.
!Note!
A note highlights actions or procedures which, if not performed correctly, can have an indirect
effect on operation or trigger an unexpected response on the part of the device.
%Direct current
A terminal to which DC voltage is applied or through which direct current flows.
&Alternating current
A terminal to which alternating voltage (sine-wave) is applied or through which alternating current
flows.
)Ground connection
A grounded terminal, which as far as the operator is concerned, is already grounded by means of a
grounding system.
*Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
+Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential
equalization line or a star grounding system depending on national or company codes of practice.
Connecting cable immunity to temperature change
Indicates that the connecting cables have to withstand a temperature of 85°C at least.
Safety instructions
Observe the safety instructions in the associated Operating Instructions.
>
=
t 85°C