Endress+Hauser Proline Promass A 100 User manual

Products Solutions Services
Brief Operating Instructions
Proline Promass A 100
Coriolis flowmeter
These Instructions are Brief Operating Instructions; they do not
replace the Operating Instructions included in the scope of
supply.
For detailed information, refer to the Operating Instructions
and other documentation on the CD-ROM provided or visit
"www.endress.com/deviceviewer".
KA01144D/06/EN/02.13
71231777

Table of contents Proline Promass A 100
2 Endress+Hauser
Table of contents
1 Document information ..................................................... 3
1.1 Symbols used .................................................................. 3
2 Basic safety instructions ................................................... 5
2.1 Requirements for the personnel .................................................... 5
2.2 Designated use ................................................................. 5
2.3 Workplace safety ............................................................... 6
2.4 Operational safety .............................................................. 6
2.5 Product safety ................................................................. 7
3 Product description ........................................................ 8
3.1 Product design ................................................................. 8
4 Incoming acceptance and product identification .......................... 10
4.1 Incoming acceptance ............................................................ 10
4.2 Product identification ........................................................... 11
5 Storage and transport .................................................... 12
5.1 Storage conditions ............................................................. 12
5.2 Transporting the product ........................................................ 12
6 Installation ............................................................... 14
6.1 Installation conditions .......................................................... 14
6.2 Mounting the measuring device ................................................... 21
6.3 Post-installation check .......................................................... 22
7 Electrical connection ..................................................... 23
7.1 Connection conditions .......................................................... 23
7.2 Connecting the measuring device .................................................. 31
7.3 Hardware settings ............................................................. 33
7.4 Ensuring the degree of protection .................................................. 38
7.5 Post-connection check .......................................................... 39
8 Operation options ........................................................ 40
8.1 Structure and function of the operating menu ......................................... 40
8.2 Access to the operating menu via the Web browser ..................................... 40
8.3 Access to the operating menu via the operating tool .................................... 44
9 System integration ....................................................... 48
10 Commissioning ........................................................... 48
10.1 Function check ................................................................ 48
10.2 Establishing a connection via FieldCare .............................................. 48
10.3 Configuring the device address via software ........................................... 49
10.4 Configuring the measuring device .................................................. 49
10.5 Defining the tag name .......................................................... 49
10.6 Protecting settings from unauthorized access .......................................... 50
11 Diagnostic information ................................................... 53

Proline Promass A 100 Document information
Endress+Hauser 3
1 Document information
1.1 Symbols used
1.1.1 Safety symbols
Symbol Meaning
DANGER
A0011189-EN
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will
result in serious or fatal injury.
WARNING
A0011190-EN
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in serious or fatal injury.
CAUTION
A0011191-EN
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in minor or medium injury.
NOTICE
A0011192-EN
NOTICE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.1.2 Electrical symbols
Symbol Meaning
A0011197
Direct current
A terminal to which DC voltage is applied or through which direct current flows.
A0011198
Alternating current
A terminal to which alternating voltage is applied or through which alternating current flows.
A0017381
Direct current and alternating current
•A terminal to which alternating voltage or DC voltage is applied.
• A terminal through which alternating current or direct current flows.
A0011200
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding
system.
A0011199
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
A0011201
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential
equalization line or a star grounding system depending on national or company codes of
practice.

Document information Proline Promass A 100
4 Endress+Hauser
1.1.3 Tool symbols
Symbol Meaning
A0011221
Allen key
A0011222
Open-ended wrench
1.1.4 Symbols for certain types of information
Symbol Meaning
A0011182
Allowed
Indicates procedures, processes or actions that are allowed.
A0011183
Preferred
Indicates procedures, processes or actions that are preferred.
A0011184
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
A0011196
Reference to graphic
Refers to the corresponding graphic number and page number.
,… ,
Series of steps
Result of a sequence of actions
1.1.5 Symbols in graphics
Symbol Meaning
1, 2, 3,... Item numbers
,… ,
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections

Proline Promass A 100 Basic safety instructions
Endress+Hauser 5
Symbol Meaning
A0013441
Flow direction
-
A0011187
Hazardous area
Indicates a hazardous area.
.
A0011188
Safe area (non-hazardous area)
Indicates a non-hazardous area.
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
‣Trained, qualified specialists must have a relevant qualification for this specific
function and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before beginning work, the specialist staff must have read and understood the
instructions in the Operating Instructions and supplementary documentation as well
as in the certificates (depending on the application)
‣Following instructions and basic conditions
2.2 Designated use
Application and media
The measuring device described in these Instructions is intended only for flow
measurement of liquids and gases.
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or in
applications where there is an increased risk due to process pressure, are labeled
accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation
time:
‣Only use the measuring device in full compliance with the data on the nameplate
and the general conditions listed in the Operating Instructions and supplementary
documentation.
‣Based on the nameplate, check whether the ordered device is permitted for the
intended use in the hazardous area (e.g. explosion protection, pressure vessel
safety).
‣Use the measuring device only for media against which the process-wetted materials
are adequately resistant.

Basic safety instructions Proline Promass A 100
6 Endress+Hauser
‣If the measuring device is not operated at atmospheric temperature, compliance
with the relevant basic conditions specified in the device documentation provided
(on the CD-ROM) is absolutely essential.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage
caused by improper or non-designated use.
!WARNING
Danger of breakage of the measuring tube due to corrosive or abrasive fluids.
Housing breakage due to mechanical overload possible!
‣Verify the compatibility of the process fluid with the measuring tube material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Observe the specified pressure and temperature range.
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide
assistance in verifying the corrosion resistance of fluid-wetted materials, but does
not accept any warranty or liability as minute changes in the temperature,
concentration or level of contamination in the process can alter the corrosion
resistance properties.
Residual risks
The external surface temperature of the housing can increase by max. 20 K due to the
power consumption of the electronic components. Hot process fluids passing through
the measuring device will further increase the surface temperature of the housing. The
surface of the sensor, in particular, can reach temperatures which are close to the fluid
temperature.
Possible burn hazard due to fluid temperatures!
‣For elevated fluid temperature, ensure protection against contact to prevent burns.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣It is recommended to wear gloves on account of the higher risk of electric shock.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.

Proline Promass A 100 Basic safety instructions
Endress+Hauser 7
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to
meet state-of-the-art safety requirements, has been tested, and left the factory in a
condition in which it is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC
directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.

Product description Proline Promass A 100
8 Endress+Hauser
3 Product description
3.1 Product design
3.1.1 Device version with HART, Modbus RS485 and PROFIBUS DP
communication types
2
3
4
1
A0017609
 1 Important components of a measuring device
1 Transmitter housing cover
2 Main electronics module
3 Transmitter housing
4 Sensor
In the case of the device version with Modbus RS485 intrinsically safe, the Safety
Barrier Promass 100 forms part of the scope of supply.

Proline Promass A 100 Product description
Endress+Hauser 9
3.1.2 Device version with EtherNet/IP communication type
2
3
4
5
1
A0017257
 2 Important components of a measuring device
1 Transmitter housing cover
2 I/O electronics module for EtherNet/IP
3 Main electronics module
4 Transmitter housing
5 Sensor

Incoming acceptance and product identification Proline Promass A 100
10 Endress+Hauser
4 Incoming acceptance and product identification
4.1 Incoming acceptance
A0015502
1
+
2
1
+
2
A0013843
A0013695
A0015502
A0013698
A0015502
A0013699