Endress+Hauser Levelflex M FMP43 User manual

BA357F/00/en/03.09
No. 71074935
Valid as of software version:
01.04.zz
Operating Instructions
Levelflex M FMP43
Run Time Measurement

Brief overview Levelflex M FMP43 with HART/4...20 mA
2Endress+Hauser
Brief overview
For quick and simple commissioning:
Safety instructions →ä6
Explanation of the warning symbols
You can find special instructions at the appropriate position in the chapter in
question. The positions are indicated with the icons Warning #, Caution "and
Note !
Æ
Installation →ä12
The steps for installing the instrument and installation conditions (e.g.
dimensions) can be found here.
Æ
Wiring →ä27
The instrument is virtually completely wired on delivery.
Æ
Display and operating elements →ä33
An overview of the position of the display and operating elements can be found
here.
Æ
Commissioning via VU331 display →ä47
In the "Commissioning" section, you learn how to switch on the instrument
and check the functions.
Æ
Commissioning via Endress+Hauser operating program →ä61
In the "Commissioning" section, you learn how to switch on the instrument
and check the functions.
Additional information on the operating via the Endress+Hauser operating
program (FieldCare) can be found in Operating Instructions BA027S/04.
Æ
Troubleshooting →ä72
If faults occur during operation, use the checklist to locate the cause.
Here you can find measures you can take yourself to take remedial action
against the fault.
Æ
Index →ä93
You can find important terms and keywords on the individual sections here.
Use the keyword index to find the information you need quickly and efficiently.

Levelflex M FMP43 with HART/4...20 mA Brief overview
Endress+Hauser 3
Brief operating instructions
L00-FMP40xxx-19-00-00-en-012
!Note!
These Operating Instructions explain how to install and commission the level transmitter. All the
functions that are required for a typical measuring task are taken into account here.
In addition, the Levelflex M has many other functions that are not included in these Operating
Instructions, such as functions for optimizing the measuring point and converting the measured
value.
An overview of all the instrument functions can be found on →ä86.
An extensive description of all the instrument functions can be found in BA245F –
"Description of Instrument Functions" on the CD-ROM provided.
Operating Instructions can also be found on our homepage: www.endress.com
E
+
-
+
E
+
-
E
E
-
… …
… …
KA189F/00/a2/03.07
52012501
52012501
100%
0%
F
E
UB
FMP43
FMP40
FMP41C
FMP45
LN
D
L
Levelflex M - Brief operating instructions
input E
(see sketch)
input F
(see sketch) displayed
D and L are confirm
or specify
range
suggestion
000
measured value
Group
selection
00
basic setup
01
safety settings
09
display
04
linearisation
05
extended calibr.
0C
system
parameters
092
language
0A
diagnostics
0A0
present
error
002
tank
properties
004
process
cond.
005
empty
calibr.
006
full
calibr.
008
dist./
meas value
051
check
distance
003
medium
property
052
range of
mapping
053
start
mapping
008
dist./
meas value
- envel. curve
- substracted signal
- mapping
- single curve
- cyclic
= 100: unlocked
¹ 100: locked
09A
plot settings
09B
recording
curve
0A1
previous
error
0A4
unlock
parameter
(333 = reset customer parameters)
0A3
reset
threaded
connection
1½
(G 1
:
reference point of
measurement
¾ or BSP
¾orG ½)
¾or1½NPT
03
length
adjustment
030
end of
probe
031
probe
length
032
probe
033
probe
length
034
determine
length
- unknown
- 1.4 … 1.6
- 1.6 … 1.9
- 1.9 … 2.5
-4…7
- 2.5 … 4
->7
0E
envelope curve
Contrast: +or +
- standard
- aluminium tank
- plastic tank
- bypass/pipe
- coax-probe
- concrete
wall
- standard
- fast
change
- test: no filter
- slow
change
- free
- tie down
isolated
- tie down
gnd.
If shortened
please enter probe length here.
reference point of
measurement
F = measuring span
E = empty distance (= zero)
UB = upper blocking distance
LN = probe length
L = level
D = distance

Brief overview Levelflex M FMP43 with HART/4...20 mA
4Endress+Hauser

Levelflex M FMP43 with HART/4...20 mA Table of contents
Endress+Hauser 5
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 6
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Installation, commissioning and operation . . . . . . . . 6
1.3 Operational safety and process safety . . . . . . . . . . . . 6
1.4 Notes on safety conventions and icons . . . . . . . . . . . 7
2 Identification . . . . . . . . . . . . . . . . . . . . 8
2.1 Instrument designation . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3 Certificates and approvals . . . . . . . . . . . . . . . . . . . 11
2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 11
3 Installation . . . . . . . . . . . . . . . . . . . . . 12
3.1 Incoming acceptance, transport, storage . . . . . . . . . 12
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 13
3.3 Installation instructions . . . . . . . . . . . . . . . . . . . . . 18
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 23
3.5 Cleaning of the probe . . . . . . . . . . . . . . . . . . . . . . 24
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 27
4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . . . . 27
4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 29
4.3 Recommended connection . . . . . . . . . . . . . . . . . . 32
4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 32
4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 32
5 Operation . . . . . . . . . . . . . . . . . . . . . . 33
5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . . 33
5.2 Display and operating elements . . . . . . . . . . . . . . . 35
5.3 Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.4 Display and acknowledging error messages . . . . . . 40
5.5 HART communication . . . . . . . . . . . . . . . . . . . . . . 43
6 Commissioning. . . . . . . . . . . . . . . . . . 44
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6.2 Switching on the measuring instrument . . . . . . . . . 44
6.3 Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6.4 Basic Setup with the VU331 . . . . . . . . . . . . . . . . . 47
6.5 Blocking distance . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.6 Envelope curve with VU331 . . . . . . . . . . . . . . . . . 57
6.7 Function "envelope curve display" (0E3) . . . . . . . . 58
6.8 Basic setup with the Endress+Hauser
operating program . . . . . . . . . . . . . . . . . . . . . . . . . 61
7 Maintenance. . . . . . . . . . . . . . . . . . . . 67
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.2 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.3 Repairs to Ex-approved instruments . . . . . . . . . . . . 67
7.4 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
8 Accessories . . . . . . . . . . . . . . . . . . . . . 68
8.1 Weather protection cover . . . . . . . . . . . . . . . . . . . . 68
8.2 Weld-in adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
8.3 Remote display and operation FHX40 . . . . . . . . . . . 69
8.4 Commubox FXA191 HART . . . . . . . . . . . . . . . . . . 70
8.5 Commubox FXA195 HART . . . . . . . . . . . . . . . . . . 70
8.6 Commubox FXA291 . . . . . . . . . . . . . . . . . . . . . . . 70
8.7 ToF Adapter FXA291 . . . . . . . . . . . . . . . . . . . . . . . 70
8.8 Protective cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
8.9 Calibration kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
9 Troubleshooting . . . . . . . . . . . . . . . . . 72
9.1 Troubleshooting instructions . . . . . . . . . . . . . . . . . 72
9.2 System error messages . . . . . . . . . . . . . . . . . . . . . . 73
9.3 Application errors . . . . . . . . . . . . . . . . . . . . . . . . . 75
9.4 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
9.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
9.7 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
9.8 Contact addresses of Endress+Hauser . . . . . . . . . . . 78
10 Technical data . . . . . . . . . . . . . . . . . . . 79
10.1 Additional technical data . . . . . . . . . . . . . . . . . . . . 79
11 Appendix. . . . . . . . . . . . . . . . . . . . . . . 86
11.1 HART operating menu (display module) . . . . . . . . 86
11.2 Description of functions . . . . . . . . . . . . . . . . . . . . . 88
11.3 Function and system design . . . . . . . . . . . . . . . . . . 88
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Safety instructions Levelflex M FMP43 with HART/4...20 mA
6Endress+Hauser
1 Safety instructions
1.1 Designated use
The Levelflex M FMP43 is a compact level transmitter for continuous measurement in liquids, using
the guided level radar/TDR: time domain reflectometry measuring principle.
1.2 Installation, commissioning and operation
The Level M is designed to meet state-of-the-art safety requirements and conforms to applicable
standards and EC regulations. If installed incorrectly or used for applications for which it is not
intended, however, the instrument can present a source of application-related danger, e.g. product
overflow due to incorrect installation or configuration. For this reason, installation, connection to
the electricity supply, commissioning, operation and maintenance of the measuring system must
only be carried out by trained, qualified specialists authorized to perform such work by the facility's
owner-operator. The specialists must have read and understood these Operating Instructions and
must follow the instructions they contain. Modifications and repairs to the instrument are
permissible only when they are expressly approved in the Operating Instructions.
1.3 Operational safety and process safety
Alternative monitoring measures must be taken to ensure operational safety and process safety
during configuration, testing and maintenance work on the device.
Hazardous area
Applicable national standards must be observed when using the measuring system in hazardous
areas. The instrument is accompanied by separate “Ex documentation”, which is an integral part of
this documentation. The installation regulations, connection values and safety instructions listed in
this document must be observed.
• Ensure that all personnel are suitably qualified.
• Measuring point requirements with regard to measurement and safety must be observed.

Levelflex M FMP43 with HART/4...20 mA Safety instructions
Endress+Hauser 7
1.4 Notes on safety conventions and icons
In order to highlight safety-relevant or alternative operating procedures in the manual, the following
conventions have been used, each indicated by a corresponding symbol in the margin.
Safety instructions
#Warning!
Indicates
an action or procedure which, if not performed correctly, can result in serious personal
injury, a safety hazard or the destruction of the instrument.
"Caution!
Indicates
an action or procedure which, if not performed correctly, can result in personal injury or the
incorrect operation of the instrument.
!Note!
Indicates an action or procedure which, if not performed correctly, can have
an indirect effect on operation or trigger an unexpected response on the part of the instrument.
Explosion protection
0Explosion protected, type-examined equipment
If the instrument has this symbol embossed on its nameplate, it can be used in a hazardous area or a
non-hazardous area, according to the approval
-Explosion hazardous area
This symbol is used in the drawings of these Operating Instructions to indicate hazardous areas.
Instruments in hazardous areas, or cables for such instruments, must have appropriate explosion
protection.
.Safe area (non-hazardous area)
This symbol is used in the drawings of these Operating Instructions to indicate non-hazardous areas.
Instruments in the non-hazardous area also have to be certified if connecting cables lead into the
hazardous area.
Electrical symbols
%Direct current
A terminal to which DC voltage is applied or through which direct current flows.
&Alternating current
A terminal to which alternating voltage (sine-wave) is applied or through which alternating current
flows.
)Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded by means of a grounding
system.
*Protective ground connection
A terminal which must be connected to ground prior to making any other connection to the equipment.
+Equipotential connection
A connection that has to be connected to the plant grounding system:
This may be a potential equalization line or a star grounding system depending on national or company
codes of practice.
Temperature resistance of the connecting cables
Indicates that the connecting cables have to withstand a temperature of 85 C at least.
Safety instruction
For safety instructions refer to the manual for the appropriate instrument version.
t >85°C

Identification Levelflex M FMP43 with HART/4...20 mA
8Endress+Hauser
2 Identification
2.1 Instrument designation
2.1.1 Nameplate
The following technical data are given on the instrument nameplate:
L00-FMP4xxxx-18-00-00-en-001
Fig. 1: Information on the nameplate of the Levelflex M FMP43 (example)
2.1.2 Ordering structure
In this diagram, mutually exclusive variants are not identified.
Made in Germany
D-79689 Maulburg
Dat./Insp.:
Order Code:
IP68 / NEMA 6P
Ser.-No.:
4-wire
ENDRESS+HAUSER
t >85°C
TA > 70°C :
D01301-A
if modification
see sep. label
X= Patents
LEVELFLEX-M
90 … 253 V AC 3,5VA
10,5…32VDC 1W
16 … 3 V DC 0,8W
Profibus PA
Foundation Fieldbus
LN= PN=
4 … 20 mA HART 2-wire
Order No
(see Order Information)
Communication
variant and
supply voltage
Serial number
Reference to additional
safety-relevant documentation
Designation according to Directive 94/9/EC
and designation of protection
10 Approval:
A Non-hazardous area
1 ATEX II 1/2 G Ex ia IIC T6
7 ATEX II 1/2 G Ex d (ia) IIC T6
5 ATEX II 1/2 G Ex ia IIC T6, ATEX II 1/3 D
3 ATEX II 2G Ex e mb (ia) IIC T6
2 ATEX II 1/2 D, Alu blind cover
4 ATEX II 1/3 D
M FM DIP Cl. II Div. 1 Gr. E-G N. I.
S FM IS Cl. I, II, III Div. 1 Gr. A-G N. I.
T FM XP Cl. I, II, III Div. 1 Gr. A-G
N CSA General Purpose
P CSA DIP Cl. II Div. 1 Gr. G + coal dust, N. I.
U CSA IS Cl. I, II, III Div. 1 Gr. A-D, G + coal dust, N. I.
V CSA XP Cl .I, II, III Div. 1 Gr. A-D, G + coal dust, N. I.
K *TIIS Ex ia IIC T4
I *NEPSI Ex ia IIC T6
Y Special version, to be specified
20 Probe:
300 mm - 4000 mm/12 in - 157 in
K ..... mm, rod 8 mm, 316L, Ra < 0.76 μm/30 μin Price per 100 mm
M ..... in, rod 8 mm 316L, Ra < 0.76 μm/30 μin Price is based on one inch
S ..... mm, rod 8 mm, 316L, electropolished Ra < 0.38 μm/15 μin Price is based on 100 mm
T ..... in, rod 8 mm 316L, electropolished Ra < 0.38 μm/15 μin Price is based on one inch
Y Special version, to be specified
30 O-ring Material; Temperature:
5 EPDM, FDA, USP Cl. VI; - 20 °C to 130 °C
6 Kalrez, FDA, USP Cl. VI; - 20 °C to 150 °C
9 Special version, to be specified

Levelflex M FMP43 with HART/4...20 mA Identification
Endress+Hauser 9
40 Process Connection:
-- Threaded boss --
U1J Thread M24, 316L, install > accessory weld-in adapter
-- Clamp connections --
TCJ Tri-clamp ISO2852 DN25-38 (1 to 1-1/2"), 316L, 3A, EHEDG
TDJ Tri-clamp ISO2852 DN40-51 (2"), 316L, 3A, EHEDG
TFJ Tri-clamp ISO2852 DN70-76.1 (3"), 316L, 3A, EHEDG
-- Hygienic connections --
T7J SMS 1-1/2" PN25, 316L, EHEDG
TXJ SMS 2" PN25, 316L, EHEDG
MAJ DIN11864-1 A DN25 tubr DIN11850, 316L, EHEDG
MQJ DIN11851 DN40 PN40, 316L, EHEDG
MRJ DIN11851 DN50 PN40, 316L, EHEDG
S1J NEUMO BioControl DN25 PN16, 316L, EHEDG
-- ANSI flanges --
AEJ 1-1/2" 150 lbs RF, 316L flange ANSI B16.5
AFJ 2" 150 lbs RF, 316L flange ANSI B16.5
YY9 Special version, to be specified
50 Power Supply; Output:
B 2-wire ; 4 - 20mA SIL HART
D2-wire;PROFIBUSPA
F 2-wire; FOUNDATION Fieldbus
G 4-wire 90 - 250 VAC; 4 - 20mA SIL HART
H 4-wire 10.5 - 32 VDC; 4 - 20mA SIL HART
Y Special version, to be specified
60 Operation:
1 W/o display, via communication
2 4-line display VU331
3 Prepared for FHX40
9 Special version, to be specified
70 Type of Probe:
1 Compact, basic version
5 Compact, detachable
6 Remote, cable 3 m, detachable
7 Remote, cable 6 m, detachable
9 Special version, to be specified
80 Housing:
A F12 Alu, coated IP68 NEMA 6P
C T12 Alu, coated IP68 NEMA 6P, separate conn. compartment
B F23 316L IP68 NEMA 6P
D T12 Alu, coated IP68 NEMA 6P + OVP1), seperate terminal compartment
Y Special version, to be specified
90 Cable Entry:
2 Gland M20 (EEx d > thread M20)
3 Thread G 1/2
4 Thread NPT 1/2
5PlugM12
6 Plug 7/8"
9 Special version, to be specified
100 Additional Option:
A Basic version
B EN 10204-3.1 material (316L wetted parts) inspection certificate
H *5-point linearity protocol, see additional spec.
J *5-point, 3.1, 5-point linearity protocol, see additional spec.,
EN10204-3.1 material (316L wetted parts), inspection certificate
P CoC, EN 10204-3.1 material (316L wetted parts) inspection certificate
R *5-point, CoC, 3.1, 5-point linearity protocol, see additional spec.,
EN10204-3.1 material (316L wetted parts), inspection certificate
Y Special version, to be specified
995 Marking:
1Tagging(TAG)
2 Bus address

Identification Levelflex M FMP43 with HART/4...20 mA
10 Endress+Hauser
You can fill in the options of the respective feature into the following table. The filled in options
result in the complete order code.
1) OVP = overvoltage protection
FMP43- complete product designation
⇓
Please enter probe length in mm or inch / 0.1 inch
mm
inch / 0.1 inch
probe lenght LN →Page 14

Levelflex M FMP43 with HART/4...20 mA Identification
Endress+Hauser 11
2.2 Scope of delivery
"Caution!
It is essential to follow the instructions concerning the unpacking, transportation and storage of
measuring instruments given in the chapter "Incoming acceptance, transport, storage" on →ä12!
The scope of delivery consists of:
• Assembled instrument
• Endress+Hauser operating program (on the enclosed CD-ROM supplied)
• Accessories (see Section 8).
Accompanying documentation:
• Brief operating instructions (basic setup/troubleshooting): housed in the instrument
• These Operating Instructions
• Approval documentation: if not included in the Operating Instructions.
!Note!
You can find BA245F - "Description of Instrument Functions" on the CD-ROM supplied.
2.3 Certificates and approvals
CE mark, declaration of conformity
The instrument is designed to meet state-of-the-art safety requirements, has been tested and left the
factory in a condition in which it is safe to operate. The instrument takes into account applicable
standards and regulations which are listed in the EC declaration of conformity and thus meets the
legal requirements of the EC Directives. Endress+Hauser confirms the successful testing of the
instrument by affixing to it the CE mark.
2.4 Registered trademarks
KALREZ®, VITON®, TEFLON®
Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
HART®
Registered trademark of the HART Communication Foundation, Austin, USA
PulseMaster®
Registered trademark of Endress+Hauser GmbH+Co. KG, Maulburg, Germany

Installation Levelflex M FMP43 with HART/4...20 mA
12 Endress+Hauser
3 Installation
3.1 Incoming acceptance, transport, storage
3.1.1 Incoming acceptance
Check the packing and contents for any signs of damage.
Check the shipment, make sure nothing is missing and that the scope of supply matches your order.
3.1.2 Transport
"Caution!
Follow the safety instructions and transport conditions for instruments of more than 18 kg. Do not
lift the measuring instrument by the probe rod in order to transport it.
3.1.3 Storage
Pack the measuring instrument in such a way as to protect it reliably against impact for storage and
transportation. The original packing material provides the optimum protection for this.
The permissible storage temperature is -20 °C to +80 °C.

Levelflex M FMP43 with HART/4...20 mA Installation
Endress+Hauser 13
3.2 Installation conditions
3.2.1 Dimensions
Housing (see feature 80 in "Ordering information") - dimensions and materials
Dimensions for the process connection and the probe type →ä14.
L00-F12xxxx-06-00-00-en-001
L00-T12xxxx-06-00-00-en-001
L00-F23xxxx-06-00-00-en-001
ENDRESS+HAUSER
65 78
max. 110
85
150
Ø 129
(Aluminium)
F12 housing
ENDRESS+HAUSER
78
85
65
162
max. 100 94
Ø 129
(Aluminium)
T12 housing
max. 94 104
Ø 129
150
40
(316L)
F23 housing

Installation Levelflex M FMP43 with HART/4...20 mA
14 Endress+Hauser
Probes (see Feature 70 in "Ordering information") - Dimensions and materials
L00-FMP43xxx-06-00-00-en-001
88
88
103
99
17
Ø54
4xØ8,5
R50
≥
Ø5
F12 / T12 / F23 housing
option “6/7”:
remote electronic
option “1”:
compact
Probe length LN
Probe length LN
Probe length LN
Probe length LN
option “5”:
compact, detachable
reference point of
measurement
➀Insulator
Material Approval
Ketron PEEK LSG FDA, 3A,
USP Cl. VI
➁O-ring (see Feature 30 in "Ordering information"
Material Approval Temperature range Option
EPDM Freudenberg 70 EPDM 291
FDA, 3A,
USP Cl. VI
- 20 °C to 130 °C (functional)
- 20 °C to 121 °C (3A Class. II, USP Cl. VI) 5
FFKM DuPont Kalrez 6221 - 20 °C to 150 °C (functional)
- 20 °C to 149 °C (3A Class. I, USP Cl. VI) 6
➂Probe (see Feature 20 in "Ordering information)
Material Version Option
316L (1.4435)
0.76 μm mechanically polished K, M
0.38 μm electropolished S, T
Hastelloy C22 Special version available on request Y
➀
➁
➂
process
connection
(example)
M24 x 1.5

Levelflex M FMP43 with HART/4...20 mA Installation
Endress+Hauser 15
Process connections (see Feature 40 in "Ordering information") - Dimensions and
materials
Endress+Hauser supplies DIN/EN flanges made of stainless steel AISI 316L with the material
numer 1.4435 or 1.4404. With regard to their stability-temperature property, the materials 1.4435
and 1.4404 are grouped together under 13E0 in EN1092-1 Tab.18.
The chemical composition of the two materials can be identical.
Process connection Designation Versions Approvals Option
Tri-clamp ISO2852
DN25-38 (1 to 1-½")*
Pmax = 16 bar
•0.76μm
•0.38μm
electropolished
•5
•EHEDG
• ASME-BPE
compliant
TCJ
Tri-clamp ISO2852
DN40-51 (2")*
Pmax = 16 bar
TDJ
Tri-clamp ISO2852
DN70-76.1 (3")
Pmax = 10 bar
TFJ
SMS 1-½" PN25
with slotted nut*
Pmax = 16 bar
•0.76μm • EHEDG
T7J
SMS 2" PN25
with slotted nut*
Pmax = 16 bar
TXJ
Ø 50,4
43,4
Ø 63,9
56,4
Ø 90,9
83,4
74
25
Ø 54,85
26
84
Ø 63,9
56,4

Installation Levelflex M FMP43 with HART/4...20 mA
16 Endress+Hauser
DIN11851 DN40 PN40
with slotted nut F40*
Pmax = 16 bar
•0.76μm
•EHEDG
MQJ
DIN11851 DN50 PN40
with slotted nut F50*
Pmax = 16 bar
MRJ
DIN11864-1 A DN25
Pipe DIN11850
with slotted nut F25*
Pmax = 16 bar
•0.76μm
•0.38μm
electropolished
MAJ
NEUMO BioControl
DN25 PN16*
Pmax = 16 bar
S1J
1-1/2" 150lbs RF
Flange ANSI B16.5*
Pmax = 16 bar
•0.76μm
AEJ
2" 150lbs RF
Flange ANSI B16.5*
Pmax = 16 bar
AFJ
Process connection Designation Versions Approvals Option
21
78
Ø39
Ø56
22
92
Ø51
Ø68
21
63
Ø 42,9
30,430,4
6464
1717
2020
127
17,5
152,4
19,1

Levelflex M FMP43 with HART/4...20 mA Installation
Endress+Hauser 17
All metal parts used in the process in 316L (1.4435)
Thread M24 x 1.5 Accessory:
weld-in adapter
U1J
Weld-in adapter
order number: 71041381
Pmax = 16 bar
•0.76μm
Process connection Designation Versions Approvals Option
Ø65
M24 x 1,5

Installation Levelflex M FMP43 with HART/4...20 mA
18 Endress+Hauser
3.3 Installation instructions
3.3.1 Mounting tools
A 4 mm Allen key is needed to turn the housing.
3.3.2 General instructions
Normally use rod probes. Rope probes are used for measuring ranges > 4m and with restricted
ceiling clearance which does not allow the installation of rigid probes.
!Note!
You must ensure that the probe does not come into contact with the container wall, container
bottom and tank internals.
Mounting location
• Do not mount the probe in the filling curtain
(2).
• Mount the probe at such a distance away from
the wall (B) that, in the event of buildup on
the wall, there is still a minimum distance of
100 mm between the probe and the buildup.
• Mount the probe as far away as possible from
internals.
• The minimum distance from the probe end to
the tank floor is 10 mm.
• If installing outdoors, it is recommended that
you use a weather protection cover (1). See
"Accessories" on →ä68.
L00-FMP43xxx-17-00-00-xx-001
B
12
C
Tank internals
• If the distance to the internals is < 300 mm,
"mapping" must be carried out, and the
measurement capability may be restricted.
• During operation, the probe must not touch
any internals within the measuring range.
Optimization options
• Interference echo suppression: measurement
can be optimized by electronically suppressing
interference echoes.
L00-FMP43xxx-17-00-00-xx-002
5

Levelflex M FMP43 with HART/4...20 mA Installation
Endress+Hauser 19
3.3.3 Special instructions
When installing in tanks with agitator, observe the lateral loading capacity of rod probes:
• 10 Nm with 1.4435 / SS316L
• 16 Nm with Hasteloy C22 (on request).
The formula for calculating the bending torque M impacting on the probe:
with
cw: Friction factor
ρ [kg/m3]: Density of the medium
v [m/s]: Velocity of the medium perpendicular to the probe rod
d [m]: Diameter of the probe rod (8 mm)
L [m]: Level
LN[m]: Probe length
L00-FMP43xxx-16-00-00-de-004
Calculation example
L00-FMP43xxx-16-00-00-xx-003
Friction factor [cw] 0.9 (on the assumption of a turbulent
current (high Reynolds number ))
Density [ρ] in kg/m31000 (e.g. water)
Probe diameter [d] in m 0.008
L = LN(worst case)
M=c · ·v ·d·L·(L −0.5·L)
WN
2
r
2
v
LN
L
d
Bending torque [M] on rod probes
Probe length [ ] in meters
L N
v=0.5m/s
v=0.7m/s
v=1.0m/s
max. bending torque
0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 4
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
Bending [Nm]
torque

Installation Levelflex M FMP43 with HART/4...20 mA
20 Endress+Hauser
3.3.4 Notes on special installation situations
The probe must be mounted opposite the
agitator.
If possible, check whether a non-contact
process, ultrasonic or level-radar would be
better suited, particularly if the agitator
generates large mechanical loads on the probe.
L00-FMP43xxx-17-00-00-xx-005
Installation at an angle
• For mechanical reasons, the probe should be
installed as vertically as possible.
• The maximum mounting angle is
– up to 1 m = 30°
– up to 2 m = 10°
– up to 4 m = 5°.
L00-FMP43xxx-17-00-00-xx-006
0...30°
0...10°
0...5°
0...1 m
1...2 m
2...4 m