Eneo IAM-6MC1001M0A User manual

Package
EPoC Transceiver DC Cable &
DC Terminal Block
Hardware Overview
Right
Left
BNC 커넥터
EPoC Transceiver
EPoC Transceiver
DC 전원 어댑터
상태 표시등
Join 버튼
DC OUT스위치RJ45 DC OUT 표시등 터미널 블럭
Status LED
indicator
DC Power Jack Join Button
BNC connector
DC OUT LED
DC OUT
ON / OFF Switch
Terminal Block
Overview
This device is aHigh-Speed, long distance Ethernet &PoE extender
that makes possible to transmit IP data up to 2.4Km up to 1.2Km
through various analog cables in different situations.
It is cost-effective and time saving solution to migrate existing analog
system to IP based system since EPoC Transceiver supports
easy installation utilizing the existing CCTV cable (Coax, UTP, 2wire &
Etc.).
With long distance transmission feature, the device makes to
overcome 100 meters distance limitation easily and reduces the
construction cost significantly compared with fiber optic configuration.
Features
Ethernet over coax (UTP, 2-Wire) communication following
IEEE1901 Standard
Data (or UTP, 2-wire)
Data distance up to 2.4Km
Max. 270Mbps Bandwidth
10/100/1000 Full Duplex
128bit AES network encryption
Supports Multi-connection (Daisy chain, Star, etc.)
Supports UTP, Telephone (2 Pairs), 2-Wire cable communication
(Using BTE Series)
Quality LED (Data & Power)
Plug & Play
Surge Protection
12VDC output (for Non-PoE Camera)
Please read carefully the instruction manual before use. Depending
on the model, the image and the actual look of the product may vary.
LED Indicators
Indicator Color Function
BNC Join EPoC Devices connected
PWR 56VDC input connected
Quality
LINK Good data connection
Poor data connection
PWR Good power supply condition
Additional adapter required
Data Flashes when data is transferred
DC OUT DC OUT switch is ON
Installation Guide
1. Set the IP address on the camera following the instruction manual
of the camera.
Î
If the camera IP is automatically assigned (DHCP, etc.), there is no
need to set the camera IP separately.
2. Connect BNC of the coaxial cable to each EPoC Transceiver.
3. Connect 56V DC power to EPoC Transceiver first and then to AC
outlet. transmission up to 1200m over RG6 coaxial cable.
4. When they are correctly connected, PWR/BNC Join/Quality PWR LED
are on.
5. Fix up EPoC Transceiver where it should be placed.
6. Connect the UTP(LAN) cable between EPoC Transceiver and NVR
first and then between EPoC Transceiver and camera.
7. Connect DC Cable between camera and Terminal Block on EPoC
Transceiver.
Î EPoC Transceiver send data via BNC connector.
Î
Mind
the
polarity (+/-) and tie up DC cable on the terminal block.
8. Ping test is recommended to confirm the whole network after
installation.
9. Check the video signal on the monitor.
Quick Installation Guide
Ethernet over Coax Transceiver,
Data/Power supply 270Mbps,
57VDC power input
IAM-6MC1001M0A
Quick
Installation
Guide
Quick Installation
Guide
Note: The Join Button is currently disabled.

Caution
Please install the device following the installation guide.
Do not touch the device and cable with wet hands.
Keep away from moisture and shock.
Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
Indoor use only.
Do not use for other purposes.
Do not disassemble or modify this device.
Do not put any sticker or paint on it.
If this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
Please use the rated power supply for the product.
Connect DC power to this device first and then to AC outlet.
Warranty
This device has passed the quality control and product inspection.
Please install and use according to the installation guide.
The warranty period for this product is 36 months from the date of
purchase.
If this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
Any damages or breakage from user’s abuse, accident, modification
or natural disasters will not be covered manufacturer’s warranty.
This device complies with part 15 of the fcc rules. Operation is subject to the
following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference
that may cause undesired operation
Applications
12V DC OUT
Non-PoE IP
Camera
Coaxial
10/100 Ethernet
56V DC/1.2A
Power Supply
NVR
EPoC Transceiver
Network Switch
DC OUT: ON
Specification
Model IAM-6MC1001M0A:1 Port Transce iver
Interfa
ce
Coax 1 x 75Ω BNC (Female) - Ethernet over Coax (B-LinX)
Ethernet 1 x RJ45 - 10/100/1000 Base-T with Auto-detect MDIX
Transmission Rate 270Mbps Full Duplex (PHY: 500Mbps)
Transmission
Distance Ethernet up to 2.4Km(RG-6)
LED
Indication
Ethernet 1 x Data(Green)
EPoC 1 x BNC Join(Green)
Power 1 x PWR(Blue)
Link Quality 1 x Good(Green) / 1 x Bad(Red)
Power Quality 1 x Good(Green) : 40V~57V / 1 x Bad(Red) : 40V Under
12VDC out 1 x 12V DC OUT(Green)
Encryption 128-bit AES
Power
Input B-Linx or DC12V~ 57V
DC Output DC12V / 2A
Me chanical Dimension 132(L) x 83(W) x 28(H)mm
Weight 198g
Environment
Operating Temp -20 ~ 60°C
Storage Temp -30 ~ 80°C
Relative
Humidity 10% ~ 90%
Compliance Certification FCC, CE, KC, RoHS
Surge Protection IEC 61000-4-5 4kV(1.2 / 50us), 2kA(8 / 20us)
Optional Accessories 56VDC / 1.2A External Power Supply
eneo® is a registered trademark of VIDEOR E. Hartig GmbH
Exclusive distribution through specialised trade channels only.
VIDEOR E. Hartig GmbH, Carl-Zeiss-Straße 8, 63322 Rödermark/Germany
Tel. [phone] / 888-0
Fax [phone] / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig GmbH Version 06/2019
EPoC Transceiver