ENERDOOR FINHRM5.032.M User manual


PASSIVE HARMONIC FILTER
FINHRM5.032.M
Operation Manual

FINHRM5.032.M
2of6
2. Product model, principle and structure
2.1. Principle
The FINHRM5 series is designed to attenuate the level of current harmonic distortion up
to a level of 5% (TDD).
2.2. Application
The common use of Variable Speed drives based on 6 pulses input stage introduced high
level of current distortion in the electrical network.
The use of FINHRM5 series allows to reduce the level of distortion caused by these
device into level not dangerous and specified in different standards (i.e. IEEE519).
2.3. Electrical characteristics FINHRM5.032.M
Rated Voltage Up to 480 V AC (±10%
Rated Current 32 A @50°C
Frequency 50 Hz
Power Loss 210 W (400 V AC)
275 W (480 V AC)
Network TN; TT
THD (Total Harmonic Distortion < 5% @ full load
TDD (Total Demand Distortion) < 5%
Overload 150% for 60 sec. every 10 minutes
Overload on no load condition < 5%
Full load drop voltage < 4%
Protection category IP 00
SCCR 30 kA
Discharge Time < 15 sec

FINHRM5.032.M
3of6
3. Product installation,
3.1. Electrical wiring
ABC
A2 B2 C2
C1
B1A1
A3 B3 C3
L1'
L2'
L3'L3
L2
L1
INPUT OUTPUT
H5D.032.2925
H5R.032.024.2925
FINC.100.M
Picture 3.1: Electric wiring.
NOTE:
1. The product is divided in 3 different blocks:
a)Main choke H5D.032.M2925
b)Trap choke H5R.032.024.2925
c)Trap cap FINC.0100.M
2. The electrical connection is indicated in the previous diagram, the OUPUT side
must be connected to the load, generally the VSD or multiple VSD, the INPUT side will
be connected to the line.
3. For the cables connection of the blocks follow the indication of the table at 3.3.
4. Connection on inout and output terminals must be done with proper cables for the
application
5. If the load is only one drive use proper protection for the drive, in case the load are
multiple VSD use proper protection for each drive.
6. The minimum distance between every block must be at least 7 cm

FINHRM5.032.M
4of6
3.2.
3.2. Mechanical dimensions and weight
104104
290
300
260
210
110
150
300
250
Ø8
100
130
200 240
Ø8
*NOTE: Measurements in mm.
H5D.032.M2925 27 Kg
H5R.032.024.M2925 25 Kg
FINC.0100.M 6 Kg
H5D.032.2925H5R.032.024.2925
FINC.0100.M

FINHRM5.032.M
5of6
3.3. Connections
CablesConnection

Terminal
connection Cable mm2(AWG)
A-A1 6
B-B1 6
C-C1 6
A2-A3 6
B2-B3 6
C2-C3 6


NOTE:ANYANDALLWIRINGSHOULDBEDONEBYALICENSEDELECTRICIAN.ANYELECTRICAL
CONNECTIONSMADEBYANON–LICENSEDELECTRICANISTOBEDONESOATTHEIROWNRISK

FINHRM5.032.M
6of6
For additional information
ITALY Finmotor S.r.l. [phone]
www.finmotor.com
GERMANY Enerdoor GmbH
[phone]
EUROPE, ASIA
(Germany Excluded)
Enerdoor SA
[phone]
www.enerdoor.com
AMERICA Enerdoor Inc. [phone]
www.enerdoor.com
Rev. 05