Energer ENI512DDH Installation manual

18V CORDLESS DRILL ENI512DDH
SAFETY AND OPERATING MANUAL
Original Instructions V 6.0

18V CORDLESS DRILL ENI512DDH
Read all safety warnings and all instructions before use. Failure to follow the
warnings and instructions may result in electric shock, re and/or serious
injury.
Save all warnings and instructions for future reference.
1

18V CORDLESS DRILL ENI512DDH
GENERAL SAFETY INSTRUCTIONS
WARNING!Read all safety warnings designated by the symbol and all
instructions.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, re and/or
serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool
1) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep Children and bystanders away while operating a power tool. Distractions
can cause you to loose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering the power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When using a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the inuence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries
c) Avoid accidental starting. Ensure the switch is in the off-position before
plugging in. Carrying power tools with your ngers on the switch or plugging in power
tools that have the switch in invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of a power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
2

18V CORDLESS DRILL ENI512DDH
better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can get
caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these devices
can reduce dust-related hazards
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it is
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventative safety measures reduce the risk of starting power
tools accidentally.
d) Store idle power tools out of reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions and in the manner intended for the particular type of power tool,
taking into account the working conditions and the work to be performed. Use of
the power tool for operations different from those intended could result in a hazardous
situation
5) Battery tool use and care
a) Ensure the switch is in the off position before inserting the battery pack.
Inserting the battery pack into power tools that have the switch on invites trouble.
b) Recharge only with the charger specied by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of re when used with another
battery pack.
c) Use power tools only with specifically designed battery packs. Use of any
other battery packs may create a risk of injury or re.
d) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the terminals together
may cause burns or a re.
e) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, ush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the battery may cause irritation or
burns.
3

18V CORDLESS DRILL ENI512DDH
6) Service
Have your power tool serviced by a qualied repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
SPECIAL SAFETY INSTRUCTIONS
1. Wear ear protection when using the cordless drill. Exposure to the noise can
cause hearing loss.
2. Hold power tool by insulated gripping surfaces, when performing an operation
where the drilling accessory may contact hidden wiring or its own cord. Drilling
accessory contacting a “live” wire may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
3. Remove the battery pack from the drill before carrying out adjustments.
4. Do not expose to rain or water.
5. Do not store the battery pack in temperatures over 40°C.
6. Always charge the battery pack between temperatures 0°C to 30°C. Ideal charging
temperature is 18°C to 24°C.
7. Only use the charger and the battery pack provided no others.
8. Avoid short circuit of the battery pack connections (screws & nails).
9. Do not charge a damaged battery pack.
10. Replace any damaged supply cords on your charger, this must be carried out by a
suitably qualied person.
11. Always disconnect the charger from power supply before making or breaking the
connections to the battery pack.
12. Battery pack and charger will be warm during charging, this is normal.
13. When not in use,please always remove the charged battery pack from the charger.
14. Always remove the battery pack from the charger immediately after re-charging is
completed.
15. Do not dispose of batteries in fire, or with household waste. Return exhausted
batteries to your local collection or recycling point.
16. Always check walls, oors and ceilings for hidden power cables and pipes.
17. Accessories and metal parts can become very hot.
WARNING!
Some dust created by power sanding, sawing, grinding, drilling, and other construction
activities contains chemicals known to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and other masonry products, and
- arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well-ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to lter out microscopic particles.
4

18V CORDLESS DRILL ENI512DDH
SAFETY ADVICE FOR RECHARGEABLE BATTERY AND
CHARGER
WARNING! During the use of tools supplied with batteries, the basic safety measures
must be followed in order to reduce fire hazards, electrolyte leakage and personal
injury, including the following precautions:
Ensure that the battery pack is suitable for the tool.
Ensure that outside surface of the battery pack is clean and dry before connecting it to
the charger.
Ensure that the batteries are charged using the correct charger recommended by the
manufacturer.
Incorrect use can create a risk of electric shock, overheating or the leaking of corrosive
liquid from the battery.
If there is an electrolyte leak, avoid any contact with the skin. In the event of a leak,
wipe with a rag. If the liquid comes into contact with the skin, rinse abundantly with
water. In the event of a reaction or contact with the eyes or mucous membranes,
consult a doctor.
Ensure that the appliance is properly switched off before inserting the battery into
the appliance. Inserting a battery into a appliance while it is switched on can cause
accidents.
Use the appliance only with the type of battery indicated in the instructions. Using
another type of battery can create a serious risk of injury and cause a re.
When the battery is not in use, keep it away from metal objects such as coins, keys or
other small metal objects that can create a connection between one terminal and the
other. Short-circuiting the terminals of batteries can cause burns to the user and cause
a re.
Dispose of batteries
Ensure that the battery is properly disposed of:
1-Do not throw it away
2-Do not to burn it
3-Do not throw it in a river
4-Dispose of it in the designated collection containers (ask your retailer)
It must ensure that the battery pack is adapted to the tool and is reloaded with an
appropriate recommended charger (battery reference ENI513BAT, charger reference
ENB514CHR) Incorrect use may result in electric shock, overload or electrolyte
leakage.
5

18V CORDLESS DRILL ENI512DDH
FOR CHARGER
1. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
2. Charger is double insulated for additional electrical safety.
3. Charger is for indoor use only.
4. If the charger supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualied persons in order to avoid a hazard.
5. Never charge damaged batteries as these can short circuit and over heat.
6. When the charger is in use it MUST be supervised , if there is any evidence of
overheating then IMMEDIATELY disconnect the charger from the power supply.
7. If gas or smoke is emitted from the battery during charging switch off the power
supply and move to a well vented area to allow the fumes to vent to atmosphere.
Caution is there is leaking liquid from the battery wear protective clothing, glasses and
clothes as this can be acidic.
8. Always disconnect battery charger and remove battery from charger when the
charging is complete.
9. Only use the battery charger specically stated on the base of the battery.
10. Don’t charge non-rechargeable battery.
6

18V CORDLESS DRILL ENI512DDH
NOISE INFORMATION
Wear hearing protection!
Measured sound values determined according to EN 60745.
The noise figures quoted are emission levels and are not necessarily safe working
levels. Whilst there is a correlation between the emission and exposure levels,
this cannot be used reliably to determine whether or not further precautions are
required. Factors that inuence the actual level of exposure of work-force include the
characteristics of the work room, the other sources of noise, etc. i.e. the number of
machines and other adjacent processes, and the length of time for which an operator
is exposed to the noise. Also the permissible exposure level can vary from country.
This information, however, will enable the user of the machine to make a better
evaluation of the hazard and risk.
VIBRATION
The European Physical Agents (Vibration) Directive has been brought in to help reduce
hand arm vibration syndrome injuries to power tool users. The directive requires power
tool manufacturers and suppliers to provide indicative vibration test results to enable
users to make informed decisions as to the period of time a power tool can be used
safely on a daily basis and the choice of tool.
Further advice can be found at www.hse.gov.uk
Vibration total values (triax vector sum) determined according to EN 60745:
Drilling into metal Vibration emission value ah,D = 0.569 m/s²
Uncertainty K = 1.5 m/s²
Screwdriving Screwdriving Vibration emission value ah =0.398 m/s²
Uncertainty K = 1.5 m/s²
The declared vibration emission value should be used as a minimum level and should
be used with the current guidance on vibration.
The declared vibration emission been measured in accordance with a standardised
test stated above and may be used to compare one tool with another tool.The declared
vibration emission value may also be used in a preliminary assessment of exposure.
WARNING!
The vibration emission value during actual use of the power tool can differ from the
declared value depending on the ways in which the tool is used dependent on the
following examples and other variations on how the tool is used:
How the tool is being used and the materials being cut or drilled.
The tool being in good condition and well maintained The use the correct accessory
for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles.
And the tool is being used as intended by its design and these instructions.
While working with this power tool, hand/arm vibrations occur. Adopt the correct
working practices in order to reduce the exposure to vibration.
7

18V CORDLESS DRILL ENI512DDH
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
WARNING!
Identify safety measures to protect the operator that are based on an estimation of
exposure in the actual conditions of use (taking account of all parts of the operating
cycle such as the times when the tool is switched off and when it is running idle in
addition to the trigger time).
Vibration and noise reduction
To reduce the impact of noise and vibration emission, limit the time of operation, use
low-vibration and low-noise operating modes as well as wear personal protective
equipment.
Take the following points into account to minimize the vibration and noise exposure
risks:
1.Only use the product as intended by its design and these instructions.
2.Ensure that the product is in good condition and well maintained.
3.Use correct application tools for the product and ensure they in good condition.
4.Keep tight grip on the handles/grip surface.
5.Maintain this product in accordance with these instructions and keep it well lubricated
(where appropriate).
6.Plan your work schedule to spread any high vibration tool use across a number of
days.
Emergency
Familiarise yourself with the use of this product by means of this instruction manual.
Memorise the safety directions and follow them to the letter. This will help to prevent
risks and hazards.
1.Always be alert when using this product, so that you can recognise and handle risks
early. Fast intervention can prevent serious injury and damage to property.
2.Switch off and disconnect from the power supply if there is any malfunction. Have
the product checked by a qualied specialist and repaired, if necessary, before you put
it into operation again.
Health Surveillance
All employees should be part of an employer’s health surveillance scheme to help
identity any vibration related diseases at an early stage, prevent disease progression
and help employees stay in work.
Residual risks
Even if you are operating this product in accordance with all the safety requirements,
potential risks of injury and damage remain. The following dangers can arise in
connection with the structure and design of this product:
1. Health defects resulting from vibration emission if the product is being used over
long periods of time or not adequately managed and properly maintained.
8

18V CORDLESS DRILL ENI512DDH
2. Injuries and damage to property due to broken application tools or the sudden
impact of hidden objects during use.
3. Danger of injury and property damage caused by ying objects.
WARNING!
This product produces an electromagnetic eld during operation! This eld may under
some circumstances interfere with active or passive medical implants! To reduce the
risk of serious or fatal injury, we recommend persons with medical implants to consult
their doctor and the medical implant manufacturer before operating this product!
Important note
Be sure the supply is the same as the voltage given on the rating plate of charger.
Remove the mains plug / battery pack before carrying out any adjustment or servicing.
Intended use
The machine is intended for driving in and loosening screws and bolts as well as for
tightening and loosening nuts within the respective range of dimension.
And it can be used to drill holes on wood, plastic or metal.
9

18V CORDLESS DRILL ENI512DDH
LOGOS
To reduce the risk of injury, user must read instruction manual
Warning
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
Double insulation
Conformity to CE directive
Always charge the battery pack between temperatures 0°C to 40°C
Indoor use only
Do not expose to rain or water
Do not burn
1 hour charging time
Before charging, read the instructions
This symbol indicates that this battery contains lithium. This battery
shall be brought to your shop to be recycled.
Safety thermal fuse
yyWxx Manufacturing date code: Year of manufacturing (20yy) and week of
manufacturing (Wxx);
1 h
2A
10

18V CORDLESS DRILL ENI512DDH
COMPONENTS AND CONTROLS
1 Keyless chuck
2 Torque adjustment ring
3 Forward, reverse rotation and lock control
4 ON/OFF switch with variable speed control
5 Battery pack
6 Gear control
7 LED light
8 LED battery capability indicator
9 Charger
10 Charging base
11 Battery pack release button
12 Bit Holder
11

18V CORDLESS DRILL ENI512DDH
TECHNICAL DATA
Item reference ENI512DDH
Rated voltage: 18V
No load speed: 0-400 min-1/0-1300 min-1
Chuck capability: 13mm
Number of clutch position: 21+D Torque setting(For drilling)
Maximum torque: 25N.m
Max drilling capability: Wood: 30 mm
Steel: 13 mm
Machine weight: 1.6 kg
Normal charging time: 1 hour
Battery pack ENI513BAT
18V Li-Ion, 1300mAh
Charger "ENB514CHR
INPUT:100-240V ~ 50-60Hz 0.8A
OUTPUT:21V 1.5A"
Sound pressure level : LpA =69,3dB(A) Uncertainty K=3dB(A)
Sound power level : LwA =80,3 dB(A) Uncertainty K=3dB(A)
Wear ear protection when sound pressure is over 80dB(A)
ACCESSORIES
The drill is equipped with the following accessories:
- 2 pcs battery pack
- 1 pc charger and 1pc charging base
- 1pc double head screw bit(CRV) PH2 slot 6
12

18V CORDLESS DRILL ENI512DDH
CHARGING PROCEDURE
1. BEFORE USING THE CORDLESS DRILL
If the machine is new, the battery must rst be charged.
A new battery or one which has not been used for an
extended period achieves full performance only after few
times charging and discharging cycles.
Attention!
After storing for a long time, the battery capacity will be
reduced.
A substantial drop in operating period per charge indicates
that the battery is worn out and must be replaced.
Warning!
The charger and battery pack are specically designed to
work together so do not attempt to use any other devices.
Never insert or allow metallic objects into charger or battery
pack connections because an electrical failure and hazard
will occur.
2. TO CHARGE THE BATTERY PACK
The power voltage supply must conform to that specied on
the rating plate of the charger.
Always inspect the battery charger, cord and plug for signs
of damage before use.
-Connect the charger to the charger base.
- Remove the battery from the device by pressing the lock
button (g. 1) and slide the battery to remove (g. 2)
-Move the battery into the charger for connections(g.3).
-Connect the battery charger to the power supply. The
red LED lights to indicate that charging has begun. A
discharged battery at normal ambient temperature will take
approximately 1 hour to reach full charge. When charging is
nished, the indicator changes from red to green.
-Press the lock button and then remove the battery from the
charging base (g.4).
-Unplug the charger, and then remove the battery pack.
ALWAYS disconnect the charger from the power source
when it is not in use.
State of Charge (g.5):
-When charging begins: the indicator changes from green to
red.
-When the load is over: the indicator changes from red to
green.
(g. 1)
(g. 2)
(g. 3)
(g. 4)
(g. 5)
13

18V CORDLESS DRILL ENI512DDH
3. LED battery capability indicator
You can check the battery capability at any time by press
the LED battery capability indicator (g. 6)
When the three lights are on, the battery is full. When two
lights are on, it shows that the battery capacity begins to
decrease. And if only see the red LED, it indicates the
battery need to be recharged.
Warning!
When battery charge runs out after continuous use or
exposure to direct sunlight or heat, allow time for the tool to
cool down before re-charging to achieve the full charge.
4. TO REMOVE OR INSTALL BATTERY PACK
Locate battery pack release buttons on back of battery pack
and depress and slide to release battery pack from the drill.
To insert the battery pack into drill and then simple slide will
be sufcient.
OPERATING INSTRUCTIONS
1. INSTALLING AND REMOVING BITS
Warning!
Always remove the battery before you change the drill or
screw bit to avoid unintentional starting of the machine.
1. Open the drill chuck by holding the machine and turn
chuck in an anti-clockwise direction, until the jaws are open
enough. (Fig.7)
2. Insert the bit firmly into the chuck. To tighten, turn the
chuck (while holding the machine) in a clockwise direction
until the bit is fully installed and maintained. (Fig.8)
3. To remove the bit, just open the chuck and then remove it
by hand.
2. USE A BIT HOLDER FOR SCREWDRIVER BITS
Insert the magnetic bit holder in the chuck according to
above steps and place the bit into the holder which been
selected.(Fig.9)
To remove the bits, just pull out the bit by hand.
(g. 9)
(g. 8)
(g. 7)
(g. 6)
14

18V CORDLESS DRILL ENI512DDH
3. ON/OFF SWITCH WITH BRAKE FUNCTION
Depress the On/Off switch to start and release it to stop
your drill. The on/off switch is fitted with a brake function
which stops your chuck immediately when you quickly
release the switch.
4. VARIABLE SPEED
This tool has a variable speed switch that delivers higher
speed and higher torque with increased trigger pressure.
Speed is controlled by the amount of switch trigger
depression.
Warning!
Do not operate for long periods at low speed because
excess heat will be produced internally.
5. SWITCH LOCK
The On/Off switch trigger can be locked in OFF position.
This helps to reduce the possibility of accidental starting
when not in use. To lock the switch, place the forward/
reverse rotation control in the center position.
(Fig.10)
6. REVERSIBLE
The forward/reverse rotation control located above the On/
Off switch controls the direction of rotation.
For drilling and screw driving use forward rotation, slide
the rotation lever to the right. To use reverse rotation, slide
the rotation lever to the left to remove screws or release a
jammed drill bit. (Fig.11)
Warning!
Never change the direction of rotation when the chuck is
rotating, Wait until it has stopped.
7. TWO-SPEED GEAR CONTROL
The drill has a two-speed gear control designed for drilling
or driving at low (mark is 1 0-400/min) or high (mark is 2
0-1300/min) speeds. A slide switch is located on top of the
drill for selecting. When using the drill in the low speed
range, the speed will decrease and the drill will have
greater power and torque. When using the drill in the high
speed range, the speed will increase and the drill will have
less power and torque. (Fig.12)
Warning:
To prevent gear damage, always allow the chuck to come
to a complete stop before changing the direction of rotation
or the two-speed gear control.



(g. 10)
(g. 11)
(g. 12)
15

18V CORDLESS DRILL ENI512DDH
8. TORQUE ADJUSTMENT
The torque is adjusted by rotating the torque adjustment
ring. The torque is greater when the torque adjustment
ring is set on a higher setting. The torque is less when the
torque adjustment ring is set on a lower setting. Rotate the
torque adjustment ring to the desired setting (Fig.13)
1-4: For driving small screws
5-8: For driving screws into soft material
9-12: For driving screws into soft and hard material
13-16: For driving screws into hard wood
17-21: For driving larger screws:
For drilling:
9. DRILLING
When drilling hard smooth surfaces, use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. Hold the tool
rmly and place the tip of the bit at the point to be drilled.
Depress the switch trigger to start the tool. Move the drill
bit into the work-piece, applying only enough pressure to
keep the bit drilling. Do not force or apply side pressure to
elongate a hole.
Warning:
When drilling in metal, only use HSS drill bits in good
condition. Always use a magnetic bit holder when using
short screwdriver bits. When screw-driving, apply a small
quantity of liquid soap or similar to the screw threads to
ease insertion.
10. DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle or dispose of
the battery pack properly. This battery pack contains lithium
batteries. Consult your local waste authority for information
regarding available recycling and/or disposal options.
Discharge your battery pack by operating your drill, then
remove the battery pack from the drill housing and cover the
battery pack connections with heavy duty adhesive tape to
prevent short circuit and energy discharge.
(g. 13)
16

18V CORDLESS DRILL ENI512DDH
TERMS OF USE
When all precautions have been taken and the previous operations were done, you
can start working. Always secure the work piece especially if it is small and the sheets.
Use the appropriate drill bit and the material at the correct speed.
In the woods, a burned area indicates an inappropriate speed or a bit sharpened
improperly.
In steel, lubricate to prevent overheating and premature wear of the drill.
In the lightweight construction materials use the maximum speed limit and put a great
effort all the more that the bit is large.
Stay in the extension of the machine, perpendicular to the surface to be drilled.
In the steel it is recommended to leave the drill regularly to remove chips and cool the
drill.
The stress on the machine should not be such that the speed is reduced by more than
25% for signicant periods. When overloaded passenger, run the machine empty for 3
to 5 minutes to cool the engine.
When screwing, use the tip perfectly adapted to the screw head on pain of not being
able to tighten the screws or damage. Use speed and minimum torque to start and
perform tests, and the couple can then be adjusted.
CARE AND MAINTENANCE
Disconnect the battery from the tool before making any adjustments or maintenance.
This machine requires no special mechanical maintenance such as greasing the
bearings.
Do not try to open or disassemble your drill or feeder to intervene yourself. Do not
open and replace the battery cells.
Do not let the drill dead load.
Make sure the battery pack is suitable for the tool and is charged using the correct
charger recommended. Improper use may cause risk of electric shock, overheating
or leakage of electrolyte. To protect the batteries from damage, do not expose to
temperatures above 40o
Cleaning of plastic parts is unplugged charger and battery removed, using a soft damp
cloth and a mild soap.
Never immerse the machine and do not use detergent, alcohol, gasoline, etc..
In case of problems or for a deep cleaning, consult the manufacturer, its service agent
or a similarly qualied person to avoid a hazard.
If the power cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
17

18V CORDLESS DRILL ENI512DDH
GUARANTEE
This ENERGER product carries a guarantee of 12 months.
If your product develops a fault within this period, you should, in the rst instance
contact the retailer
where the item was purchased.
This guarantee specically excludes losses caused due to:
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance
- Failure of consumable items
- Accidental damage
- Cosmetic damage
- Failure to follow manufacturer’s guidelines
- Loss of use of the goods This guarantee does not affect your statutory rights.
This guarantee is only valid in the UK. For any enquiries relating to the guarantee
please refer to your
retailer.
ENVIRONMENTAL PROTECTION
This product is marked with the selective sorting symbol on waste electrical and
electronic equipment. This means that this product should not be disposed of with
household waste but must be supported by a collection system in accordance with
Directive 2002/96/EC. It will then be recycled or dismantled to minimize impacts on
the environment, electrical and electronic products are potentially hazardous to the
environment and human health due to the presence of hazardous substances.
Do not dispose of batteries. Return exhausted batteries to your local collection or
recycling point.
Li-Ion
18

Authorised Signatory and technical file holder
Date : 22/04/2013
Signature:_________________
Name / title: Peter Harries / Quality Manager
Powersmith (UK) LTD. Trade House, Mead Avenue ,BA22 8RT
18
V
CORDLESS DRILL
ENI512DDH
Declaration of Conformity
We, Importer
Powersmith (UK) LTD.
Trade House, Mead Avenue, BA22 8RT
Declare that the product:
Designation:18V LI-ION CORDLESS DRILL
Model: ENI512DDH
Complies with the following Directives:
2004/108/EC Electromagnetic Compatibility Directive
2006/42/EC Machinery Directive
2006/95/EC Low Voltage Directive
2011/65/EU Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic
Equipment
2002/96/EC and 2003/108/EC Waste Electrical and Electronic Equipment (WEEE)
Standards and technical specifications referred to ：
Cordless drill ：
：：
：
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 60745-1:2009+A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
Charger :
EN 55014-1:2006+A1:2009
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 60355-2-29:2004+A2:2010
EN 60355-1:2002+A11:2004 +A12:2006+A2:2006+A13:2008+A14:2010+A15:2011
EN62233:2008