Energetic Lighting E1HBA Series User manual

1
LED Highbay Fixture
Installation Instructions
Model # E1HBA series
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-492-6566.
Item Number Purchase Date
ATTACH YOUR RECEIPT HERE
www.energeticlighting.com
LIGHTING

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
32
•
-
-
-
-
•
Please read and understand this entire manual before attempting to assemble, operate or
install the product. Failure to do so could lead to electric shock, fire or other injuries that
could be hazardous or even fatal.
Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or
turn off the circuit breaker.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This product must be installed in accordance with local, state and national electrical codes.
Installation work shall be completed by a licensed installer that is familiar with the
construction and operations of the product.
CAUTION:
The fixture body is one piece. Do not disassemble it.
This product can only be dimmed when connected to a 0-10v dimming system.
NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, safety
glasses.
Before begining installation, ensure that power is disconnected to the supply wires.
•
•
•
•
•
•
•
1. Back out the 3 screws at the front of the fixture body
(A) leaving about 1/4-inch between the screw head
and the fixture body.
www.energeticlighting.com www.energeticlighting.com
Part Item Name Qty.
AFixture Body 1
BReector (packaged separately) 1
CSafety Cable 1
PACKAGE CONTENTS
SAFETY INFORMATION
SAFETY INFORMATION
PREPARATION
INSTALLATION INSTRUCTIONS
Fig. 1
B
A
Back out 3 screws
leaving 1/4” of exposed
thread
A
C

4
This fixture is warranted to perform free from defects for five years. If it fails to do so, you may
return it with proof of purchase to 13445 12th St., Chino, CA 91710 for replacement.
Clean with a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or clean-
ers containing abrasive agents. When cleaning the fixture, make sure the power is turned
off, and any liquid spray should be applied to the cleaning cloth and not sprayed directly onto
the fixture itself.
www.energeticlighting.com
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
TROUBLESHOOTING
WARRANTY
Problem Possible Solution Corrective Action
Fixture does not light.
Circuit breaker trips
when light is turned on.
1. Power is off.
2. Incorrect wire connection.
3. Defective wall switch.
Crossed wires or power
wire is grounded out.
Verify wires are correctly
connected.
1. Check circuit breaker
or wall switch.
2. Check wire splices.
3. Replace switch.
2. Align the large opening of the 3 keyhole slots on the
reflector (B) with the 3 extended screws on the fixture
body (A), turn the reflector clockwise until the screw
heads sit over the narrow end of the keyhole slots.
Torque down the screws so that the reflector (B) is
secured to the fixture body (A).
Fig. 2
4. Hang the fixture onto a structural hook on the
building, ensure that the hardware is properly rated
for the fixture weight. Attach or loop the free end of
the safety cable (C) onto a structural beam or
mounting point.
Fig. 4
3. Attach one end of the safety cable (C) to a solid point
on the rear of the fixture body (A).
Fig. 3
6
Printed in China
www.energeticlighting.com
5. Route the input wires into an available junction box
securing the line with an appropriate junction box
fitting. Connect the wires black to black, white to
white, and green to green.
Dimming Connection: If fixture is to be connected to
a dimming system, connect the purple and gray leads
to its corresponding 0-10v dimming supply leads.
Otherwise, leaving the fixture 0-10v dimming leads
open will enable the fixture to run at 100% lumen
output.
Fig. 5
A
B
B
Junction
Box
C