Energetic Lighting E1STA Series User manual

1
LED Streetlight Fixture
Installation Instructions
Model # E1STA series
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-492-6566.
Item Number Purchase Date
ATTACH YOUR RECEIPT HERE
www.energeticlighting.com
LIGHTING

NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
32
•
-
-
-
-
•
Please read and understand this entire manual before attempting to assemble, operate or
install the product. Failure to do so could lead to electric shock, fire or other injuries that
could be hazardous or even fatal.
Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or
turn off the circuit breaker.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This product must be installed in accordance with local, state and national electrical codes.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CAUTION:
The fixture body is one piece. Do not disassemble it.
MIN 90°C SUPPLY CONDUCTORS.
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 40°C.
SUITABLE FOR WET LOCATIONS.
NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
•
•
•
•
•
•
•
•
•
1. Back out the 2 lock screws on the base of the fixture
(A) just enough to clear the diameter of the mounting
pole.
www.energeticlighting.com www.energeticlighting.com
Part Item Name Qty.
AFixture 1
PACKAGE CONTENTS
SAFETY INFORMATION
SAFETY INFORMATION
INSTALLATION INSTRUCTIONS
Fig. 1
A
2. Connect the wires from the fixture (A) to the supply
wires from the mounting pole: black to black, white to
white, and green to green.
Fig. 2
A
A
Back out
lock screws
Mounting Pole

www.energeticlighting.com
INSTALLATION INSTRUCTIONS
4. Secure the fixture to the post by tightening both of the
lock screws on the base of the fixture (A).
Fig. 4
3. Slip the base of the fixture (A) over the mounting pole,
ensure that wires are not pinched between the post
and adapter and that the post is seated fully inside
the adapter (B).
Fig. 3
4
This fixture is warranted to perform free from defects for three years. If it fails to do so, you may
return it with proof of purchase to 13445 12th St., Chino, CA 91710 for replacement.
TROUBLESHOOTING
WARRANTY
Problem Possible Solution Corrective Action
Fixture does not light.
Circuit breaker trips
when light is turned on.
1. Power is off.
2. Incorrect wire connection.
3. Defective switch.
Crossed wires or power
wire is grounded out.
Verify wires are correctly
connected.
1. Check circuit breaker
or power switch.
2. Check wire splices.
3. Replace switch.
5
Printed in China
www.energeticlighting.com
A
Mounting Pole