Energetic Lighting MXL2048-LED40K8040 User manual

1
Shop Light
Installation Instructions
Model # MXL2048-LED40K8040
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-492-6566.
Item Number Purchase Date
ATTACH YOUR RECEIPT HERE
www.energeticlighting.com
LIGHTING

32
Please read and understand this entire manual before attempting to assemble, operate or
install the product. Failure to do so could lead to electric shock, fire or other injuries that
could be hazardous or even fatal.
• Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or
turn off the circuit breaker.
• Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
• This product must be installed in accordance with local, state and national electrical codes.
• Installation work shall be completed by a licensed installer that is familiar with the
construction and operations of the product.
CAUTION:
• The fixture body is one piece. Do not disassemble it.
• This product can NOT be used with a dimmer switch.
NOTICE
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
• This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
• This equipment should be installed and operated with a minimum distance 20cm between
the radiator and your body.
• If the fixture will not be operated for a long period of time, the power plug should be
disconnected from the outlet.
1. Mark two (2) locations on mounting surface spaced
apart by 34-in.
Ensure that the mounting holes will be located on a
sturdy surface such as wood rafters, plywood or
drywall studs. The mounting holes should NOT be
located over a drywall surface without a backing
support, as this may not provide enough support for
the weight of the fixture.
www.energeticlighting.com www.energeticlighting.com
Part Item Name Qty.
AFixture 1
BChain 2
C“J” Hook 2
PACKAGE CONTENTS
SAFETY INFORMATION
INSTALLATION INSTRUCTIONS
Fig. 1
34-in.
Mark these two locations
on mounting surface
2. Drill pilot holes in each of the two marked locations.
Screw in the two “J” hooks (C), one in each pilot hole.
Hook the loop end of one chain (B) onto each “J”
hook (C).
Fig. 2
3. Insert the hook end of one of the chains (B) into the
support slots on the fixture back as shown in Fig. 3 to
support the fixture on the mounting surface. Repeat
for the second mounting hole.
Fig. 3
A
A
B
B
C
Pilot holes
C
B

4
www.energeticlighting.com
INSTALLATION INSTRUCTIONS
OPERATING INSTRUCTIONS
4. After mounting the fixture plug the power cord into a
grounded outlet to finish the installation.
Fig. 4
5
This fixture is warranted to perform free from defects for three years. If it fails to do so, you may
return it with proof of purchase to 13445 12th St., Chino, CA 91710 for replacement.
Clean with a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or clean-
ers containing abrasive agents. When cleaning the fixture, make sure the power is turned
off, and any liquid spray should be applied to the cleaning cloth and not sprayed directly onto
the fixture itself.
www.energeticlighting.com
CARE AND MAINTENANCE
TROUBLESHOOTING
WARRANTY
Problem Possible Solution Corrective Action
Fixture does not light.
Bluetooth® connection
cannot be established.
Poor sound quality from
speakers.
Power is off.
Reset power to fixture.
Rescan for available
devices from device settings
menu.
Device is out of range from
fixture.
Other wireless devices in
close proximity causing
interference.
Device settings may need
to be enabled or adjusted.
Check circuit breaker
or wall switch.
Unplug the power plug from
outlet, and plug back in.
Check device
Bluetooth®
settings menu.
Ensure that device has
Bluetooth® enabled, also
check that device has
sufficient battery charge.
Ensure that the fixture is
within 32 feet (10 meters) of
the
Bluetooth® device and
check for obstructions
between device and fixture.
Try relocating source device
away from other Bluetooth®
or Wi-Fi devices, or try turning
off other devices to see if
connection can be restored.
Check device volume is
not muted or set too low.
Check if the phone has any
low battery power
management regulating
Bluetooth® connection.
1. The light can be switched on and off by using the pull
chain. The speakers will continue to work whether
the light is on or off, as long as connection to
bluetooth device is maintained.
Fig. 1
2. To connect the shoplight to your Bluetooth
®
device,
plug in the shop light fixture to power on the speakers
(shop light LED illumination does not need to be
switched on), then listen for a double chime sound
from the speakers.
Enter the Bluetooth
®
menu on cell phone or other
source device and access the list of
“Available Bluetooth
®
Devices”.
Check the list of available devices on the Bluetooth
®
device to see if “SL-******” (where * stands
for a unique number) is detected. The list may need to be refreshed, or manually scanned for
new connections. Select the “SL-******” name to pair device with the fixture. Once connection
is established, the fixture speakers will emit a single chime.
If “SL-******” is not available after 1 minute of powering on, unplug the fixture power cord and
plug back in to reset the speakers.
Volume can be adjusted from your source Bluetooth
®
device.
Please note that only one Bluetooth
®
device can be connected to each fixture, and only one
fixture can be connected to each Bluetooth
®
device.
Typical connection range is approximately 32 feet (10 meters), and connection reliability may be
affected by obstructions within the room. If interruptions occur during streaming, try relocating
the Bluetooth
®
device to a different location.
Fig. 2
Available devices
...
...
...
SL-******
Bluetooth Settings