ENFORCER SD-72081-6MQ User manual

SD-72081-6MQ
Single-Gang Mortise Cylinder Key Switch
Manual

ENFORCER Single-Gang Mortise Cylinder Key Switch
2SECO-LARM U.S.A., Inc.
Introduction:
If a keypad or proximity card reader fails to activate an electronic lock, the user can switch between
normally closed (N.C.) and normally open (N.O.) contacts using the SD-72081-6MQ, forcing the
door to open. This acts as a backup for access control systems, so that the system does not rely
on the integrity of a single device.
Overview:
Specifications:
Model
SD-72081-6MQ
Switch Type
DPDT Switch (momentary)
Contact Rating
5A@125VAC, NO/NC
Dimensions
23/4”x41/2”x17/16” (69x114x37 mm)
Parts List:
1x Front cover
1x Back plate
1x Set of keys (2 pc)
Side View
11/8”
(28mm)
3/8”
(9mm)
PCB
Front View*
23/4” (69mm)
41/2”
(114mm)
Key switch
11/2”
(38mm)
15/16”
(34mm)
Features:
Keyed mortise cylinder (2 keys included)
Mortise cylinder removable for ease of keying
Flush mount with vandal-resistant screws
Chrome-plated aluminum back plate fits to single-gang box
Stainless-steel front cover conceals mounting screws
DPDT Momentary switch, 5A@125VAC contact rating, color-coded wires
Screw hole
Screw hole
*Note: Shown without cover.
2x Vandal screws
1x Security wrench
IMPORTANT: No replacement keys are
available. Please make extra copies of
your keys.

ENFORCER Single-Gang Mortise Cylinder Key Switch
SECO-LARM U.S.A., Inc. 3
1. Remove the back plate from the unit.
2. Thread the cable wire through the electrical
box and the center hole of the back plate.
3. Connect the wires to the switch using the
wiring diagram below.
4. Fasten the back plate to the electrical box
using the included mounting screws.
5. Finish assembly by snapping the front
cover onto the back plate.
Installation:
Wiring Diagram:
Sample Application:
1. An electromagnetic lock,
such as the E-941SA-600, is
connected to the normally
closed (N.C.) side of one of
the switch outputs of the
SD-72081-6MQ.
2. A strobe light, such as the
SL-1301-BAQ, is connected
to normally open (N.O.) side
of the other switch output of
the SD-72081-6MQ.
3. Activating the switch of the
SD-72081-6MQ will unlock
the electromagnetic lock and
trigger the strobe light.
Strobe Light (SL-1301-BAQ)
Electromagnetic Lock
(E-941SA-600)
SD-72081-6MQ
Vandal screws
Security wrench
(included)
Electrical box
(not included)
Front cover
Back plate
Top View of PCB
Blue: N.C.
Green: COM
Yellow: N.O.
Black: N.C.
White: COM
Red: N.O.

ENFORCER Single-Gang Mortise Cylinder Key Switch
4SECO-LARM U.S.A., Inc.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA, 92606
Website: www.seco-larm.com
PITGW1
Phone: [phone] | [phone]
Email: [e-mail]
MiSD-72081-6MQ_140729.docx
IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of
this product complies with all national, state, and local laws and codes related to locking and egress devices.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
Also Available from SECO-LARM:
Flush-Mount Request-to-Exit Plate
SD-7286-GWQ
Indoor No-Touch Sensor
SD-927PKC-NEQ
Outdoor No-Touch Sensor with
Manual Override
SD-9263-KSVQ
Mushroom Request-to-Exit Plate
SD-7201GC-PEQ
Illuminated Request-to-Exit Plate
SD-7202GC-PEQ
Piezoelectric Request-to-Exit Plate
SD-6276-SS1Q
For a complete listing of SECO-LARM products, please visit us online at www.seco-larm.com.