EnGenius DuraFon User manual

User Manual
DuraFon-SIP System
Durable, Long-Range Cordless Phone
EnGenius Customer Service
http://www.engeniustech.com/

~2~
Table of Contents
Safety Instructions.................................................................................5
General Safety Instructions ................................................................5
Product Safety Instructions ................................................................5
Battery Safety Instructions.................................................................7
Regulatory Information..........................................................................8
Equipment Checklist............................................................................ 11
Handset Illustration............................................................................. 12
Basic Handset Features.................................................................... 13
Additional Handset Features ............................................................ 15
Base Illustration............................................................................... 21
Base Features...................................................................................... 22
Basic Base Station Features.............................................................. 22
Charger Illustration.............................................................................. 23
Charger Features................................................................................. 24
Getting Started.................................................................................... 25
Base Station Installation................................................................... 25
Handset and Charger Installation...................................................... 26
Basic Operations.................................................................................. 27
Operation Modes ............................................................................ 27
A. Base Operation Modes............................................................. 27
B. Handset Operation Modes........................................................ 27
Making a Telephone Call.................................................................. 29
Making a 2-Way/ Intercom Call ........................................................ 30
Making a Broadcast ......................................................................... 30
Handset-to-Handset Calls............................................................. 30
Redial ............................................................................................. 31
Receiving a Telephone Call............................................................... 32
Receiving an Intercom Call ............................................................... 32
Ending a Call.................................................................................... 33
Adjusting Handset Receiver (Earpiece) Voice Volume ........................ 33
Adjusting Handset Speakerphone Voice Volume................................ 33
Placing a Call On Hold ...................................................................... 34
Mute............................................................................................... 34
Do Not Disturb (Silent Ring).............................................................. 34
Key Guard....................................................................................... 35
Battery Recharge and Replacement.................................................. 35

~3~
Advanced Operations........................................................................... 36
Handset Registration ....................................................................... 36
Handset Group Subscription............................................................. 37
Call Transfer.................................................................................... 38
Phonebook Operations.................................................................... 39
Programmable Feature Call.............................................................. 43
Caller ID.......................................................................................... 45
Call Manager................................................................................... 46
Incoming......................................................................................... 47
Outgoing......................................................................................... 47
Call Barring...................................................................................... 48
Visual Message Waiting Indicator (VMWI)......................................... 49
Adjust Handset Microphone Gain..................................................... 49
Adjust Headset Ring......................................................................... 50
SIP Configuration................................................................................. 51
Introduction.................................................................................... 51
Application...................................................................................... 51
VoIP Features.................................................................................. 51
Registration Handsets...................................................................... 51
Default Settings........................................................................... 52
Web Configuration ...................................................................... 52
LAN Configuration ....................................................................... 53
Base Settings............................................................................... 53
Phone Book................................................................................. 54
SIP Configuration............................................................................. 55
SIP Server.................................................................................... 55
SIP Account................................................................................. 55
Individual Account....................................................................... 56
Group Account............................................................................ 57
Audio Setting............................................................................... 58
Tools............................................................................................... 59
Admin......................................................................................... 59
Time........................................................................................... 60
Ping Test..................................................................................... 60
Firmware .................................................................................... 61
Back-up....................................................................................... 61
Reset/Reboot/Registration........................................................... 61
Menu Operations ................................................................................ 63

~4~
Technical Specifications ....................................................................... 68
Base Station........................................................................................ 70
Index .................................................................................................. 75

~5~
Safety Instructions
Caution: Your wireless telephone gives you freedom and flexibility to
stay in touch while you move around. However, when using your phone
equipment, safety instructions should be followed to avoid the risks of
fire, electric shock, injury to person, and damage to property.
General Safety Instructions
1. When using your wireless phone, ensure your safety and the safety of others:
a. Always watch where you are walking and standing.
b. Do not let a phone call distractyou from working safely.
c. If power goes out, your phone will not work. Backup power is
recommended.
2. In an emergency:
a. If an emergency occurs, dial the emergency phone number. Remember: if
you are in an area where your phone does not have a clear signal fromthe
base, it is highly probablethat the call may not go through. Locate the
nearest landline telephone or other communications device to call for help.
b. Emergency calls may not automatically provideemergency personnel with
your name, phone number or location.
3. Notice to Hearing Aid Users: This phone system is compatiblewith inductively
coupled hearing aids.
4. Notice to Cardiac Pacemaker Users: Preliminary studies doneby the US FDA
and others have shown that, although interference to the implanted cardiac
pacemaker may occur when operating very closely, wireless telephones “do not
seem to pose a significant problem for pacemaker wearers.” However, until
more is known, the FDA suggests that people with pacemakers may want to
take precautions when using or carrying a wireless telephone to ensure that
there is ample distancebetween the telephone and the pacemaker. Do not
carry the handset in a breast pocket. If you have any reason to suspect that
interference is taking place, turn off your handset immediately.
Product Safety Instructions
1. Read and understand all instructions.
2. Follow all warnings and instructions including thosemarked on the product.
3. Changes or modifications to this product not expresslyapproved by the

~6~
manufacturer will void the warranty and the FCC authorization to operate the
equipment. Use only manufacturer provided accessories.
4. Do not use the telephone near water. Never spill liquid of any kind on this
product.
5. Unplug the product from the wall telephone jack and power outlet before
cleaning. Do not use liquid or aerosol cleaners. Use damp cloth for cleaning.
6. Do not place this product on an unstable cart, stand, or table. The product may
fall and cause personal injury or damageto the productor other property.
7. Power Outage: In the event of a power outage, your handset charger will not
recharge the handset battery, and the base station will not allow you to make
an outgoing call or take an incoming call. Both the charger and the basestation
require electricity for operation. You should have a telephone that does not
require electricity available for useduring power outages, or have a temporary
backup power supply.
8. Slots or openings in the product’s housing are provided for ventilation. These
openings must not be blocked or covered. Placing the product on a bed,
carpeting, or other similar surface may block these openings and should be
avoided. This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
9. Never push objects of any kind into this product through housing
slots/openings as they may damage the product, touch dangerous voltage
points or shortout parts that could result in fire, electric shock, or injury.
10. This product should be operated only from the type of power source indicated
on the marking label. If you are not sureof the type of power supply to your
home, consultyour dealer or local power company.
11. Do not overload wall power outlets and extension cords as this may result in
fire or electric shock.
12. To avoid electric shock or burn, do not disassemblethis product. Send this
product to an authorized service center when service or repair work is required.
Call Customer Service for locations near you. Opening or removing covers may
expose you to dangerous voltages, electrical currents or other risks. Incorrect
re-assembling of the product may causeelectric shock when the product is
subsequently used.
13. Avoid using the product during a storm. There may be a risk of electric shock
from lightning.
14. Do not placethe product where persons can step, trip, or fall on it.
15. Do not placeconductive objects over or near the antenna.
16. Do not use the product to report a gas leak whil e in the vicinity of the leak.

~7~
17. Do not install thebase station or the handset charger near microwaveovens,
radios, TV sets, speakers, or other electrical equipment. These appliances may
cause interference to the product or experience interference from the product.
18. Unplug the base station or the charger adaptor from the power outlet and refer
to an authorized servicecenter under the following conditions:
a. If liquid has been spilled into the product.
b. When the power supply cord or plug is damaged or frayed.
c. If the product has been exposed to rain or water.
d. If the productdoes not operate normally by following the operating
instructions.
e. If the product has been dropped or housing has been damaged.
f. If the productshows a distinct changein performance.
Battery Safety Instructions
1. Use only manufacturer approved Li-Ion rechargeablebatteries and charger. Do
not useother types of rechargeablebatteries or non-rechargeablebatteries.
The batteries could short-circuit, and the battery enclosuremay be damaged
causing a hazardous condition.
2. Follow the charging instruction in this manual and instruction labels and
markings in the handsetand charger compartments.
3. Battery must be recycled or disposed of properly. Do not disposethe battery in
a fire. The cells may explode.
4. Do not dispose of the battery in municipal waste. Check with local codes for
disposal instructions.
5. Exercisecare in handling the batteries so you do not short-circuitthebattery
with conductive materials such as rings, bracelets, keys, pocketknives, and/or
coins. The battery or conductive material may overheat and cause burns or fire.
6. Do not expose batteries to rain or water.
7. Do not open or mutilate the battery. Released electrolyte is corrosive and may
cause injury to eyes or skin. The electrolyte may be toxic if swallowed.
8. During charging,the battery heats up. This is normal and is not dangerous.

~8~
Regulatory Information
DuraFon-SIP System
FCC ID: A8J-SP935
IC: 10103A-SP935
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may causeundesired operation.
Privacy of communications may not be ensured when using this phone.
Base Station
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device,pursuantto Part 15 of the FCC Rules. These limits aredesigned
to providereasonableprotection againstharmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordancewith the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will notoccur in a particular installation. If this
equipment does causeharmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit differentfrom that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications notexpressly approved by the party
responsiblefor compliancecould void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may causeundesired operation.

~9~
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits setforth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada Statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposurelimits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum
gain of 2 dBi. Antenna having a higher gain is strictly prohibited p er regulations
of Industry Canada. The required antenna impedance is 50 ohms.
Portable Handset
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device,pursuantto Part 15 of the FCC Rules. These limits aredesigned
to providereasonableprotection againstharmful interference in a residential
installation. This equipment generates, uses and can radiateradio frequency
energy and, if not installed and used in accordancewith the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will notoccur in a particular installation. If this
equipment does causeharmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increasethe separation between the equipment and receiver.

~10~
- Connect the equipment into an outlet on a circuit differentfrom that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications notexpressly approved by the party
responsiblefor compliancecould void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may causeundesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits setforth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada Statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiati on exposure limits setforth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with IC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This device has been designed to operate with an antenna having a maximum
gain of 2.5dBi. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna impedance is 50 ohms.

~11~
Equipment Checklist
1.
In a Base + Handset package, pleasefind the following components:
a.
Base Station x 1 (antenna installed)
b.
Base AC/DC Adapter x 1
c.
Handset x 1 (antenna installed)
d.
Handset Antenna x 1 (Long ×1)
e.
Desktop Charger x 1
f.
Charger AC/DC Adapter x 1
g.
1700mA Li-Ion Battery Pack x 1
h.
Telephone Cord x 1
i.
Quick Guide
j.
RJ45 cablex 1
2.
In a Handset package, pleasefind the following components:
a.
Handset x 1 (antenna installed)
b.
Handset Antenna x 1 (Long ×1)
c.
1700mA Li-Ion Battery Pack x 1
d.
Desktop Charger x 1
e.
Charger AC/DC Adapter x 1
f.
Quick Guide
3.
Optional Accessory
a.
Outdoor Antenna Kit (including antenna and cable)
b.
High-Gain Handset Antenna
c.
Headset

~12~
Handset Illustration
Antenna
Receiver
Belt Clip
Holder
Volume control /
Scrolling
Broadcast key
Travel charger jack
Headset jack
(2.5mm)
Battery pack
4-line LCD
END & Power
ON/OFF key
2-WAY/
INTERCOM
TALK/FLASH/
(For SIP)
Microphone

~13~
Handset Features
Basic Handset Features
1.
4-Line LCD (Liquid Crystal Display)
a.
The LCD display has LED (Light Emitting Diode) for backlighting.
b.
The 1st lineof LCD consists of icons.
c.
Icons explanation from left to right
(1)
RSSI level (Receive SignalStrength Indicator)
During a call, the number of bars is proportional to
the radio s ignal strength received.
(5)
DuraFon-SIP
REDIAL MENU
(1)(2) (3) (4) (6)
(2)
Link mode
(2.1) Call in-progress (ON/OFF-Hook)
Indicates if the phone line is in the OFF-Hookstatus.
12
(2.2) Intercom in-progress
Indicates if Intercom mode is active.
Indicates the Handset IDthat is sending the intercom call.
(3)
L
1
Line, Sound and Indication
(3.1) Line Indicator
Indicates when usingline 1 or the incoming callfrom FXO line.
S
1
(3.2) SIP Indicator
Indicates when using SIP or the incoming ca llfrom SIP.
(3.3) Enable ringer
(3.4) Disable ringer
(3.5) Ringer and vibrate mode
(3.6) Vibrate mode
(3.7) Message waiting indicator
(4)
PA
Disable PA and indicate speaker phone
(4.1) Indicates if the incoming broadcast is disabled.
(4.2) Speaker indicator
Indicates if the speakerphone is active.
(5)
11
Two-Digit Handset ID
Displays the 2-digit Handset ID of owner.
(6)
Battery Strength
Number of bars is proportional to the amount of batterytime remaining.
d.
The 2nd and 3rd lines of the LCD, maximum 16-characters each, display
status, message, menu selections, or user-editable alphanumerical
characters.

~14~
e.
The last line displays the left and right soft keys.
2.
Ringer
a.
Rings to an incoming call and intercom call.
b.
Distinctive alert sounds indicating various events:
(1)
Single beep: successful key entry.
(2)
Double beep: indicates power on/off.
(3)
Tripl e beep: failed operation.
(4)
Periodic 1-Long2-Short beeps (every 1 minute): low batterywarning; out of
range; call on hold.
Re:
No beep: invalid key entry.
3.
TALK/FLASH ( )
a.
Places or answers a telephone or intercom call .
b.
Sends a Flash signal to the phone line to retrieve a dial tone after the call
ends, or to perform the Call Waiting featureprovided by local phone
companies during a call.
4.
SPEAKERPHONE ( )
Press and hold the key for over 2-seconds to enable/disablethe speakerphone
during incoming, outgoing or intercom call.
5.
2-WAY INTERCOM (( ))
a.
Places an intercomcall to another handset, a group handset (group paging)
or all registered handsets.
b.
Intercom calls are digital, full duplex, and are conducted without the
assistance of the basestation.
6.
BROADCAST ( )
a.
Half duplex broadcasting to handsets for immediate announcement.
b.
Half duplex broadcasting to base stations .
Re：Press the key on the left top corner of the handset to activate
the broadcastfunction.
7.
Left/Right Soft Keys ( )
a.
Make menu selection.

~15~
8.
Up ( ) /Down ( ) Scrolling Keys
a.
Scroll through records and menu selections.
b.
Adjust receiver voicevolume when in the Talk mode.
c.
Press to enter received call log when in the Standby mode.
d.
Press to enter phonebook when in the Standby mode.
9.
END; On/Off Key ( )
a.
Ends a call.
b.
Leaves current menu operation, up one level .
c.
Press for 3-seconds to turn off the power.
Additional Handset Features
1.
Multiple Handsets Registration
a.
Up to 10 handsets can be registered to a basestation.
b.
ID 10-19: Individual Handset IDs.
c.
ID 1~7: Group IDs. Handsets can “subscribe” from the handset menu to
group(s) and be paged when a landline caller or an intercom caller enters a
Group ID.
2.
Ringer Vibrator
a.
Two (2) options for Line (incoming call) ringing and intercom ringing.
b.
Six (6)-level ringer volume selections
(Off/Low/Medium/High/Vibrate/Vibrate & High) for each option.
c.
Eight (8) ringer type selections for each option.
3.
Caller ID
Displays incoming call phone number and name on the LCD (needs Caller ID
service from local telephone company).
4.
Call Waiting with Caller ID
Displays 2nd incoming call information on the same phone linewhen 1st call is in
progress (needs Call Waiting with Caller ID servicefrom local telephone
company).
5.
Name Tagging with Caller ID
Match the Caller ID with the phone book entries; once matched, the LCD
screen will display the name or nicknameinstead of pure Caller ID info (needs
Caller ID servicefrom local telephone company).

~16~
6.
DND (Do Not Disturb, i.e., Silent Ring)
7.
Call Logs
a.
Redial: Stores 10 phone numbers (up to 26-digits each) dialed most
recently. Can perform last-number redial on all 10 numbers.
b.
Received and New Call Log: Total 50-entries (16-digit phone number, 16-
character names, and Date/Time stamp), needs Caller ID servicefrom local
telephone company.
c.
Phone numbers and names can be saved into phone book whilein display.
8.
Call Manager: Includes:blocking incoming call, outgoing call and assign line
dedication, lineselection.
a.
Incoming Call:
a-1. PA On/Off: Enable or disable the Broadcast feature from other
handsets or the basestation. When PA is Off, the handset cannot receive
Broadcast calls from the base station or other registered handsets, but it
can Broadcastto the base station or other registered handsets.
a-2. Line On/Off: Enable or disable theability to receive incoming call s
from telephone line call. When Line is Off, the handset cannotreceive
incoming calls from a telephone line call, but it can still make outgoing
calls.
a-3. Int. On/Off: Enable or disable the Intercom from other handsets or the
base station. When Int. is Off, the handset cannot receive Intercom calls
from the basestation or other registered handsets, but it can Intercom to
the basestation or other registered handsets.
b.
Outgoing Call
Select the mode of lineselection (Auto/Manual/Predefine line/Off) when
you make a line call.
b-1. Auto: A handset will select one of available lines from subscribed
bases before making an outgoing call. (Default)
b-2. Manual:A handset will be prompted to select from a list of available
lines before making an outgoing call. (1 for telephone line, 5 for SIP call)

~17~
b-3. Off: Disable the capability to make an outgoing call.
c.
Call Barring
c-1. Block users from dialing long distanceor international calls.
c-2. Up to 5-digits of each Call Barring setting, up to 5-entries allowed.
Changing requires you to enter the “Call Settings” (MENU-4-3).
Note: You must key in the accurateuser ID and password to perform this
feature. The default password is “0000.”
9.
Any Key Answer (except and SILENT soft Key)
a.
If you enable Any Key Answer while you have two incoming line calls
simultaneously, you can answer the SIP call or PSTN call by pressing
the scrolling key.
10.
Key-Guard
a.
When the Key-Guard is selected, all keys will belocked.
Press UNLOCK (Left) soft key followed by ＊to release it.
b.
The Key-Guard will be automatically enabled once returning back to idle
mode for 15-seconds.
11.
Dialing Prefix
a.
Up to 14-digits, including pause(s), one access code can be pre-
programmed to be added automatically in front of the dialed number
when dialing from call logs,phone book, and dial-and-send dialing.
12.
Call Hold
a.
Places call on hold.
13.
Mute
a.
Press MUTE (Left) soft key during talk, the handset microphone will be
muted.
Press UNMUTE (Left) soft key to release it.
14.
Phone Book
a.
50-entries, each stores a phone number or handset ID (up to 26-digits) and
name (up to 16-characters).
b.
Alphabetically sorted display and search by letter.
c.
Dial fromdisplay.
d.
During the stand-by mode, you can enter the phone book by pressing

~18~
the scrolling key.
e.
Phone Book transfer via air
i. Transfer a specific PhoneBook to one handset or all registered
handsets
ii. Transfer all PhoneBooks to one handset or all registered handsets
15.
Key Tone
a.
Four-level Key Tone volume selections (Off/Low/Medium/High).
b.
Four Key Tone type selections.
16.
Call Timers
a.
Displays call timeduration for current call ,during and immediately after
the call.
17.
ProgrammableFeature Call
a.
Allows user to pre-program the most frequently used Feature codes into
the DuraFon-SIP, which is adjunctto the PBX system.
b.
Up to 10-entries can be saved.
c.
Once the feature code has been programmed, you can quickly perform
those functions during the call by pressing the OPTION softkey.
18.
Menu Display
a.
To avoid mis-setup in the “Call Settings”(MENU-4), “Phone Settings”
(MENU-5), and “Base Settings” (MENU-6), these settings can be hidden.
b.
The Handset password is required before entering Menu Display (MENU-
8), the default handset password is “0000.”
c.
When disabling the settings, they will no longer be displayed unless
enabled by entering Menu Display again.
19.
PA On/Off
a.
Enable or disable the Broadcast function.
b.
When PA is Off, the handset cannot receive Broadcast from the base
station or other registered handsets; but it can broadcastto other
registered handsets.
20.
Group Setting
a.
Allows the handset to subscribeto one or several groups.
Re: Up to 7 groups (1~7) can be subscribed.
21.
Custom Name
a.
Change the “DuraFon-SIP” screen to the desired wording or info, such as

~19~
the handset user’s name.
Re: Up to 32-characters can beentered.
22.
Change Pwd
a.
Change the handset password, which requires entering the Call Barring
(MENU-4-3) and Menu Display (MENU-8).
Re: Default PIN is “0000.”
23.
DTMF Duration (from web)
24.
ProgrammableFlash Key Timing (from web)
25.
Assign Next Handset ID for New Handsets
a.
Use a registered handset from MENU-6-1 to assign a Next Handset ID to a
new handset.
b.
If you do not assign Next Handset ID, the system will automatically assign a
handset ID to a new handset.
c.
When entering the Base Settings, a PIN is required. The Default is “0000.”
26.
Clear Handset
a.
Use a registered handset from MENU-6-2 to remove the other registered
handset, in casethe other registered handset is defected.
b.
Once the other registered handset is clear, the user is able to register a
new handset in its place.
c.
When entering the Base Settings, the PIN is required. Default is “0000.”
27.
Change PIN
To change the base PIN, enter the “Base Settings” (MENU-6-3).
a.
Use a registered handset to change the PINfrom MENU-6-3.
b.
The default PIN is “0000.”
c.
When entering the Base Settings, the PIN is required. The default PIN is
“0000.”
28.
Auto Hang Up Feature (from web)
a.
From Web, “System-Base Settings-Auto Hang up”to turn On/Off this auto
hang up feature.
b.
If turning On the feature, the handset will automatically hang up the call
when the far-end hangs up its call.
29.
Mic Gain
Change the handset microphone gain based on the handset’s usein different
environments –Quiet, Normal and Noisy environment.

~20~
a. This requires entering the “Phone Settings” (MENU-5-1).
30.
Headset Ring
Change the ringer emitting either from the handset speaker or the headset
receiver.
a. This requires entering the “Phone Settings ” (MENU-5-8).
31
Base Intercom Auto-Answer (from web)
a.
From Web, “System-Base Settings-Base Intercom Auto-Answer” to turn
On/Off the Intercom Auto-Answer feature.
b.
Default is ON, If turning OFF the feature, you will need to press the base
Intercom or Broadcast key to answer handset Intercom calls to the base.