ENHANCED VISION Flipper Series User manual

Users Manual
Flipper™
The Ultimate in Flexibility ‑ Just Point and See!
Flipper Stand™
Flipper™
FlipperPanel™

Congratulations on your purchase of one of the Flipper family of products.
Enhanced Vision products are designed to give you the highest quality
and convenience available.
Flipper products can enable people with low vision to read, write and to see
objects at any distance. The unique design of these products are the ultimate
in flexibility and offer a large range of magnification with multiple viewing
options that make reading easier than ever. Simply connect the Flipper to
any television, LCD flat screen/computer monitor (equipped with composite
video inputs) or laptop computer (additional hardware may be required).
Prior to using this system, please carefully read and follow the instructions
provided within this booklet. A thorough understanding of the functionality
will allow you to fully benefit from the flexibility and great features of this
device.
If you have any questions, please contact the eyecare professional or the
reseller from whom you have acquired the unit.
FCC ComplianCe notiCe
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Unauthorized changes or modification to this system can void the user’s
authority to operate this equipment.
If your Low Vision device has an option to connect to a TV, it must be used
with shielded interface cables in order to meet FCC emissions limits for
Class B digital devices. It is the responsibility of the user to use the shielded
interface cables supplied with the equipment.
FCC COMPLIANCE NOTICE

5
Important Safety Precautions .......................................... 4-5
Flipper................................................................................. 7
Flipper Package Contents & Controls ................................... 8-9
Flipper Installation .................................................................. 10-11
Using Flipper .......................................................................... 12-16
FlipperPanel....................................................................... 16
FlipperPanel Package Contents & Controls .......................... 18-19
Using FlipperPanel ................................................................. 20-21
Using LCD Power Pack.......................................................... 22-24
Flipper Stand ..................................................................... 25
Using Flipper Stand................................................................ 26-29
Common Questions .......................................................... 30-34
Flipper .................................................................................... 30
FlipperPanel ........................................................................... 31-32
Flipper Stand .......................................................................... 33-34
Warranty Statement........................................................... 35
Other Enhanced Vision Products .................................... 36-38
Contact Information .......................................................... 38
SYSTEM WARNINGS
The Flipper family of products are designed to improve the quality of life for
sight impaired individuals. The extent to which Flipper products can improve
the ability to see images depends on an individual’s condition and level of
visual impairment. These products are not designed to restore vision,
correct eye conditions or halt degenerative vision loss. An eyecare
professional can determine the suitability of Flipper products for a patient's
condition.
SYSTEM PRECAUTIONS
n Avoid exposing Flipper products to extreme or rapid changes in
temperature or humidity as these conditions may cause fogging or
damage to products. Flipper products should never be placed near a
radiator or heat register.
n Do not smoke while using Flipper products. Cigarette, cigar and pipe
smoke release abrasive particles which are potentially damaging to the
Flipper optics.
n Do not use this product near water, i.e., near a bathtub, kitchen sink,
swimming pool, etc.
n Do not place this product on an unstable cart, stand or table, as the
product may fall, causing serious damage.
To obtain the maximum benefits from your Flipper product, please read
these safety precautions carefully.
IMPORTANT SAFETY PRECAUTIONS
important SaFety preCautionS

6
n Always place the excess cord in an area where it will not be damaged
by persons walking on it.
n To avoid the risk of electrical shock, do not disassemble this product.
Return it to the place of purchase if service or repair work is required.
Any attempt to disassemble your Flipper product will void the warranty.
n Always use the power supply provided within your package. Do not
attempt to use any other power supply, doing so will void the warranty.
CARING FOR FLIPPER PRODUCTS
n Always turn the power OFF when you are not using the system.
n Make sure the power is OFF or unplug your Flipper product from the
wall outlet before cleaning. Do not use liquid cleaners.
n The plastic surfaces of your Flipper product may be dusted with a dry
cloth.
n The optical surfaces should be cleaned as needed for best perfor-
mance. Dampen a lens cleaning tissue with a small amount of lens
cleaning solution and gently wipe the optical surfaces clean.
Never apply lens cleaning solution directly on any surface
of your Flipper products.
Flipper™
important SaFety preCautionS

9
8
Your Flipper is packaged in a convenient box for storage and transport. All
required accessories for operation are included.
Flipper is Comprised of:
1. Camera: Captures and enlarges the image.
2. Control Box: Connects the camera to the television set and turns
Flipper ON/OFF.
3. Viewing Options Button: For switching between color, black & white,
high contrast positive or high contrast negative viewing modes.
4. Magnification Dial: Ten preset magnification levels.
5. Light Switch: Turns the base light ON/OFF. The light can be used
when the ambient lighting is not sufficient.
6. Video Cable: Connects Flipper to the TV via the “Video Input” jack.
7. Power Supply: Connects Flipper to an AC power outlet.
2
7
1
5
4
3
6
FLIPPER PACKAGE CONTENTS & CONTROLS
Flipper paCkage ContentS & ControlS Flipper paCkage ContentS & ControlS

11
10
TV Connection Using Video Cable and "Video Input" Jack
(Refer to Figure 1)
1. Remove the Flipper and the Control Unit from the package.
2. Remove the Video Cable from the package. (This is the thin cable that
is not attached to any other component and has the same plug at both
ends.) Plug one end of the Video Cable into the Control Box Jack
labeled "VIDEO."
3. Plug the other end of the Video Cable into the yellow "VIDEO INPUT"
jack of your TV. This jack could be located on either the front, back or
side of your TV.
4. Remove the Power Supply from the package. Plug one end of the
Power Supply into the black Control Box Jack labeled "POWER." Be
sure the plug is fully inserted into the Control Box. Then plug in the
other end of the Power Supply into an AC wall outlet.
5. Turn the power on. The ON and OFF switch is on the side of the black
control box. Turn the television ON.
You can switch between using Flipper and your TV with the TV remote
control by changing between "Video" and "TV" mode.
If you have a TV with a built in VCR, you can switch between using
Flipper and your TV by pushing the “Input” button on your remote.
6. Now you can go to the
Using Flipper section on page 12 to begin
using your Flipper.
FLIPPER INSTALLATION
Flipper inStallation Flipper inStallation

13
12
Now that you have successfully installed your Flipper you can enjoy the
ease of use and operation.
Flipper can be used to view objects at a distance, up close, and at any
range in between. To maximize your usage, here are some of the things
you can do with Flipper.
nRead
nWrite
nView Distance
nWork on Hobbies
nSee Self Image
nParticipate in Class
The following steps will give you a quick start on using Flipper and practic-
ing rotating the camera head.
1. Turn the Power ON
On the side of the black Control Box, there is a switch that turns the
power ON and OFF. Turn the power ON. Make sure the TV is also
ON.
2. View the Magnified Image
Simply point the camera in the desired direction and view the magni-
fied image. The control knobs allow you to change the magnifica-
tion level and contrast.
3. Reading with Flipper
There are at least three ways that you can
magnify and read using Flipper.
A. Reading with an Upright Book Stand
(highly recommended)
Place your reading material on a stand
and place Flipper in front of the stand.
Rotate the camera head and point it at
the material. Magnify as needed using the
Magnification dial. Roll Flipper from left to
right, scanning across the page. When
you reach the end of a line, roll back to
the beginning of the line and rotate the
camera down to the next line.
There is no need to pick up or move the
camera base. Just by rotating the camera
and rolling Flipper from left to right, you
will be able to cover the entire page.
B. Reading without an Upright Book Stand
Simply place the Flipper on top of the
page and roll the unit left to right on its
easy to roll rollers. Once you reach the
end of the line, roll Flipper back to the be-
ginning of the line and rotate the camera
to read the next line.
C. Reading with the Flipper Stand
Please see page 29 for details
NOTE: The highest
magnification setting
is for distance viewing
only. (from at least 3
feet away)
uSing Flipper uSing Flipper
USING FLIPPER

15
14
You can repeat the above action and
read more than half of the page by just
rotating the camera head. Once you
have read half of the page, move the
unit and place it in the middle of the
page and repeat the rotation of the
camera head to cover the rest of the
page.
4. Writing with Flipper
Simply place the material in front of the
Flipper, rotate the camera head and
point it to the material. Adjust magnifica-
tion using the magnification knob. Start
writing and as you are writing, roll the
unit left to right on its rollers. Repeat
this action as needed.
5. Practice Using Flipper
Practice the motion of rotating the cam-
era head in different directions. Moving
the camera head away from you is gen-
erally used for viewing distant objects,
enjoying hobbies and reading items far
away from you. Moving the camera
head toward you is generally used for
writing and/or reading
SELECTING A VIEWING OPTION
You can choose a viewing option by presing
the round white button on the Flipper labeled
“Viewing Option.” Each press of the the but-
ton will change your viewing option. Push the
button to cycle through all of the options.
VIEWING OPTIONS FOR FLIPPER
Full Color Image
This mode is used most often because it
gives you a true color representation of the
image that is being magnified. This mode is
ideal for viewing objects at any distance and
for reading, writing and looking at photos.
Black and White Image
Based on your preference, you can choose the
B&W mode for viewing objects at any distance.
High-Contrast Positive Image
This mode provides a white background with
black foreground for text. This mode increases
the contrast to offer crisp text images for
reading. This mode is not appropriate for dis-
tance viewing.
High-Contrast Negative Image
This mode provides a black background
with a white foreground for text. This mode
increases the contrast to offer crisp text imag-
es for reading. This mode is not appropriate
for distance viewing.
Crisp, Clear
Text Images!
Crisp, Clear
Text Images!
uSing Flipper uSing Flipper

17
16
Changing the Magnification
To increase the magnification, slowly turn the
round knob clockwise until you feel a click.
Each click will increase the magnification.
To decrease the magnification, slowly turn
the round knob counter clockwise until you
feel a click. Each click will decrease the
magnification.
Lighting Option
When reading with the camera facing down,
Flipper has a built in light source that may
be turned ON to enhance High Contrast
Positive and Negative viewing modes.
The On/Off switch for the light is located on
the Flipper right above the light panel.
Please note, the highest magnification
setting is for distance viewing only.
(from at least 3 feet away)
The light can be used when the
ambient lighting is not sufficient.
The magnification control for Flipper is very easy to use. The magnification
control is a round dial that has ten preset magnification levels for you to
select from. FlipperPanel™
uSing Flipper

19
18
Your FlipperPanel is packaged in a soft case that is convenient for storage
and transportation. All required accessories for operation are included.
FlipperPanel is comprised of:
1. 12” LCD Screen.
2. LCD Screen mounting bracket.
3. LCD Power Pack.
4. Rechargeable Battery: energy source for 3 to 5 hours.
5. On/Off Switch for LCD Power Pack.
6. Flipper Camera: rotates 225 degrees to capture and enlarge the
image.
7. Viewing Options Button: changes viewing options from color, black &
white, high contrast positive and high contrast negative.
8. Magnification Dial: provides 10 different level of magnification.
Accessories included:
9. Power Supply: connects to LCD Power Pack and power cord.
10. Power Cord: connects to power supply and wall outlet.
11. 6-foot RCA Video Cable: connects LCD Power Pack to a TV.
12. Lens Cloth: used to clean the Flipper camera and LCD screen.
13. Soft Carrying Case.
Additional options (available separately):
14. Additional Rechargeable Battery: energy source for 3 to 5 hours.
7
8
6
3
4
1
2
910
12
5
13
11
FLIPPERPANEL PACKAGE CONTENTS & CONTROLS
Flipperpanel paCkage ContentS & ControlS Flipperpanel paCkage ContentS & ControlS