eNovates Single Wallbox User manual

Generation 2022 single wallbox
Pedestal single/double
Installation manual
Drafted alpha version – no nal release

To acces the Single Wallbox Installation Manual
please scan the QR code
To acces the Pedestal Installation manual
please scan the QR code
To acces the Single Wallbox User Manual
please scan the QR code

3
CONTENTS
Required tools............................................................................... 4
Pedestal installation................................................................... 5
Anchor attachment ........................................................................ 6
Pedestal mounting ......................................................................... 8

4
REQUIRED TOOLS
PH2
T25
1
23
4
5
67
8
9
10
11
12
13
10 L

5
# Description Amount
1 eNovates pedestal x1
2 Spirit level x1
3 Folding rule x1
4 Screwdriver Torx T25 x1
5 Screwdriver PH2 x1
Only required when installing on soft soil:
6 Anchor x1
7 Spade x1
8 Concrete 75 kg
9 Bucket of water 10 liter
10 Large mixing tub x1
11 Mixer x1
12 Hammer drill x1
13 Drill 10 mm x1
PEDESTAL INSTALLATION
The base of the pedestal can be xed to an anchor that is buried in
the ground.
Carefully consider where the charging station will be created, and
how the charger unit(s) will need to be oriented. The anchor will
be set into the ground and the pedestal will be set on the anchor,
aligned with the holes in the anchor pole. Keep this in mind when
considering the desired nal orientation of the charger unit(s).
Make sure that the power cord and Ethernet cable are already
available (two of each cable when a double pedestal is used) and that
the cables will be able to reach up through the pedestal from below,
at the position where the pedestal will be placed. For more details,
refer to the main installation manual for your product.

6
Anchor attachment
1. Dig a hole for the ground anchor, approximately 50 cm deep and
30 x 40 cm wide.
Caution: there may be objects in the ground which you want to
avoid hitting. Check for the presence of underground objects
before you start digging.
Note: avoid digging much deeper than necessary, as this will cause
the soil to become looser. In a few years’ time, the stability
of the ground mount may degrade if the soil is too loose.
2. Make sure the necessary underground cables lead into the created
hole and stick out from it. They must be able to reach up into the
charger unit and to be connected to the charger unit when the
anchor and pedestal are placed.
3. Assemble the anchor.
12
34

7
4. Lead the cables through the anchor’s central axis until they stick
out, and place the anchor in the hole. Make sure the anchor is
level and that the pedestal can be attached to the pole slot at
surface level.
5. Make sure the pedestal bracket is facing the way you want it to.
When properly positioned, x the pedestal to the anchor slot with
3 screws.
6. Pour concrete to x the anchor in place. Let the concrete harden.
If necessary, add a layer of ller soil on top of the hardened
concrete and stomp the soil down until it is level.
7. Feed the cables from the anchor through the inside of the pedestal
and out of the opening at the bottom of the pedestal bracket.
Then place the pedestal onto the anchor’s pole slot.

8
PEDESTAL MOUNTING
The mounting procedure consists of a few steps:
1. Secure the cable block to the pedestal.
2. Slide the charger onto the pedestal.
3. Secure the charger to the pedestal.
4. Connect the cables.
5. Attach and secure the cover.
6. Attach and secure the socket lid.
7. If necessary, attach a CE sticker.
Secure the cable block to the pedestal.
1. Slot the cable block onto the bottom of the pedestal bracket.
Orient the cable block so that the cables can pass from the
circular holes in the bottom corner of the pedestal bracket
through the cable block and into the charger unit, when the
charger unit is attached.

9
2. Use the provided 2 M5x16 screws (Torque 1.2Nm) to secure
the cable block onto the bottom of the pedestal bracket.
Please refer to the step “Slide the charger onto the wall
bracket” in the Wall Mounting chapter of the product manual
to perform the following steps in the mounting procedure. The
same principles that apply to the wall bracket in the product
manual from this step forward, can be applied to the pedestal
bracket.

10
Notes

11
Notes

ENP1.0.1
Manufacturer:
Enovates N.V. ● Brandstraat 13 ● 9160 Lokeren ● Belgium
KBO 0833.089.547