Enpress CTA0840BBBKP5-04C00 User manual

LEAD IN WATER SYSTEMS
    






     

  
 




 

 



.








 

     
   


    

  

,
 
    
 



   
 

  

POE 

  
 
 

Protecting Water
for Future Generations
The chemicals Peruorooctanoic
acid (PFOA), also known as C8, and
Peruorooctane sulfonic acid (PFOS)
are bio-permanent, are resistant to
direct oxidation, and do not break
down naturally in the environment
or the human body. Studies suggest
that exposure to the chemicals may
lead to cancer.
PIONEER™successfully removes these
chemicals and is installed where the
water line enters your home, business
or restaurant. This system has been
tested and third-party certied as
required in the NSF/ANSI P473 standard
for PFOA/PFOS, along with NSF/ANSI
53 standard for the reduction of lead
and cyst.
PIONEER is the First of its Kind
Whole-House Lead, Cyst & PFOA/PFOS Removal System
WHAT ARE THESE HARMFUL HOW DOES THE PIONEER SYSTEM
CHEMICALS PROTECT ME

Toxic Chemicals
in the United States
PFOA
PFOS
ENPRESS, LLC. | 34899 Curtis Blvd., Eastlake Ohio 44095 | Phone
866.859.9274 | Fax [phone] | [e-mail]
ELLC 02/2019
For more information
visit enpress.com
or OneFiltration.com
© ENPRESS LLC 2019 | ONE®is an ENPRESS Filtration Technology
THE HISTORY OF THE CHEMICALS
UNITED STATES EPA
1940's - 2015
REGULATIONS
US and International patents, and patent pending.
Common usage of a class of man-made fully uorinated
chemical compounds known to be resistant to heat,
water, and oils, incorporated into a variety of industrial
and commercial products, such as non-stick cookware
(a chemical ingredient in the production of the non-
stick coating used to make Teon®), carpets, stain
resistant clothing, food packaging, reghting foams,
adhesives, cosmetics, leather, and the lm inside
microwave popcorn bags.
The EPA currently marks the unsafe level of PFOA/
PFOS to be above 70 parts per trillion, although some
researchers and states believe lower levels are still
unsafe. Even 1 ppt may be enough to pose health risks,
leading regulators to recommend these chemicals as
candidates for the Safe Drinking Water Act.
THE CHEMICALS IN OUR
WHAT DOES THIS MEAN?
BACK YARD
THE SOLUTION
The drinking water supplies of more than 15
million Americans have water concentrations of
these compounds at levels exceeding the health
advisory limit, however this only represents
testing in half of the water supplies in the US. Other
estimates indicate the chemicals have contaminated
more than 1500 water systems nationally,
affecting up to 110 million Americans. Based
on testing by the Centers for Disease Control and
Prevention, about 98 percent of Americans have
at least some level of chemicals in their blood,
and has been found in water supplies across more
than 27 states.
It's obvious that PFOA/PFOS chemicals need to
be removed from your water. The PIONEER™POE
ltration system houses a strategically designed
nominal 0.5-micron lter to remove BOTH chemicals
along with BOTH forms of lead (soluble and
particulate) from your house in a single lter. The
PIONEER™is the First of its Kind Whole-House Lead,
Cyst & PFOA/PFOS Removal System, providing safe
drinking water throughout your entire home.
This ENPRESS system is certied
by IAPMO R&T against NSF/ANSI
Standards 53 and P473 (also CSA
B483.1) for the reduction of claims
specified on the performance
data sheet.
This ENPRESS pressure vessel
is tested and certied by NSF
International against NSF/ANSI
Standard 44 and 61 for materials and
structural integrity requirements
COMPONENT
TESTING PIONEER
PFOA/PFOS
The NSF P473 Drinking Water Treatment Units standard is
an extremely rigorous test to evaluate the effectiveness of
water treatment equipment for the reduction of chemicals
in drinking water, specically peruorooctanoic acid (PFAO)
and peruorooactane sulfonate (PFOS). The P473 standard
contains four primary sections and is similar to NSF/ANSI
53 Standard for Lead; Section 3 evaluates the Performance
of the lter to reduce the PFOA and PFOS. The US EPA’s
combined health advisory level for PFOA & PFOS is 70
parts per trillion (70 ppt) in drinking water. The inuent
level for P473 testing is 1.5 parts per billion (ppb), added as
1.0 ppb PFOS and 0.5 ppb PFOA, or 20 times the health
advisory level set by the EPA. (1.5 parts per billion is equal
to 1500 parts per trillion.) For the life of the lter, it must
reduce the inuent PFOA/PFOS concentration below 70 ppt
to comply with the requirements of the standard. ENPRESS
results are below 10 ppt.

INSTALLATION OPERATION MANUAL
This manual should be kept for future reference. If you have any questions regarding your
water lter, contact your local dealer, OEM, or the manufacturer at the following:
ENPRESS, LLC. | 34899 Curtis Blvd., Eastlake Ohio 44095
Phone [phone] | Fax [phone] | [e-mail]
EPA Est. 092577-OH-001

23
WHERE TO INSTALL
The System comes preassembled without the cartridge installed.
1. Push down the top cap with both hands to unseat the retaining ring, and remove the retaining ring by carefully grasping the handle
and pulling inward, then upward. The retaining ring should slide completely out of the groove.
2. Remove the Top Cap from the housing assembly by pulling the cap out of the top of the tank, by lifting up on the top handles. Place
removed Top Cap on a clean and dry surface, free of debris, so no contamination of the o-ring occurs.
3. Look down into the tank assembly, and you should see a small opening centered in the bottom of the tank.
4. Remove packaging from lter, then place the cartridge into the tank with the double o’ring facing down.
5. Position the cartridge so that it is aligned with the bottom, center opening.
6. Press down on the cartridge so that the double o’ring seal moves into place within the bottom, center opening.
7. Reposition the Top Cap into its original location.
8. Reattach the top tank Snap Ring, pull up on the Top Cap to seat o-rings.
9. Run water through system for 10 minutes before use.
INSTALLING THE CARTRIDGE
1. Turn off the water supply to the system by shutting off the inlet and outlet valves on the bypass.
2. (Optional) Install a 3/8” PEX tubing hose to the provided John Guest® tting and shut-off that
connects to the inlet side of the ltration system. Run the hose to a oor drain or bucket, and use to
drain sediment or to aid in lter removal during change-out.
3. Remove Umbrella Cap on the top of the vessel. Replace the 3-AAA batteries with new batteries.
Push and hold the reset button on the metered board for 3 seconds to reset the totalizer. When the
totalizer is reset the LED lights will ash green 3 times to conrm that it is reset.
4. Depressurize the system by pushing down on the red depressurization button on the top cap of the
system. Keep the button pushed down until all the air or water pressure is completely released.
5. Push down the top cap with both hands to unseat the retaining ring.
6. Remove the retaining ring by carefully grasping the handle and pulling inward, then upward. The
retaining ring should slide completely out of the groove.
7. Remove the top cap of the system by lifting up on the top handles, remove old lter.
8. Open the John Guest® tting and shut-off , and ush out the bottom of the system.
9. Look down into the tank assembly, and you should see a small opening centered in the bottom of
the tank.
10. Remove packaging from the new lter, place the new cartridge into the tank with the double o’ring
facing down.
11. Position the cartridge so that it is aligned with the bottom, center opening.
12. Press down on the cartridge so that the double o’ring seal moves into place within the bottom,
center opening.
13. Reposition the Top Cap into its original location.
14. Reattach the top tank Snap Ring, pull up on the Top Cap to seat o-rings.
15. (If completed Step 2, then…) Close the John Guest® tting and shut-off.
16. Turn the water supply on, opening the inlet and outlet valves on the bypass.
17. Relieve the system of air in the tank as the system lls with water, by pushing down on the red
depressurization button on the top cap of the system. Keep the button pushed down until all the air
pressure is completely released, and water comes out of the red depressurization button.
18. Release the red depressurization button.
19. Replace the Umbrella cap to the top of the system.
20. Check for leaks.
21. Flush the new cartridge per its installation instructions.
22. During ush, conrm green LED lights are ashing with owing water. If lights are not ashing
green, go back to step 3.
REPLACING THE CARTRIDGE
#3 UMBRELLA CAP
& LED LIGHTS
CITY WATER
INLET
WELL
INLET
RELIEF VALVE
MUST BE
INSTALLED
PRESSURE
TANK
WATER
METER
PUMP
SERVICE
GROUNDED
&
UNSWITCHED
115-
VOLT
OUTLET
The Real-time Dynamic LED System monitors water and ow rate and provides a visual color-coded
notication to the homeowner, letting them know when to replace their lter.
*Meter preset at 100,000 gallons; see page 6 for adjusting presets.
*Three AAA batteries not included, for battery back-up. Change annually with lter change-out.
EASY TO UNDERSTAND LED REPLACEMENT NOTIFICATIONS
GREEN
FILTER
GOOD
YELLOW
CHANGE
SOON
10%
FILTER
LIFE
REMAINING
RED
CHANGE
NOW
PIONEER uses state-of-the-art snap-ring technology to eliminate the need for cumbersome tools.
Homeowners can easily replace the lter in their PIONEER system by followng a few simple steps.
EASY FILTER REPLACEMENTS AND NO TOOLS REQUIRED
LIFT TOP CAPPRESS THE RED PRESSURE RELIEF VALVE & PULL SNAP-RING

45
PERFORMANCE
WARNINGS
IMAGE AND INSTALLATION INSTRUCTIONS
Plumbing the ltration system assembly: The inlet and outlet of the
ltration housing are 1” Threaded MNPT connections.
**No Use of Extra lubricants, unapproved sealants, and use of tools.
Use of tools other than hand tighten only parts, voids warranty.
Please allow 3 feet of open space above the system for replacement
cartridges.
System to be supplied only with cold water.
3-AAA batteries not included.
Meter assembly preset to 100,000 gallons
Connect #3 to #2 on
the bottom of the Filter
Housing #1
HAND TIGHTEN ONLY
Install part #7 into #3
using the threaded
connection & Teon®
tape
HAND TIGHTEN ONLY
Connect 3/8” PEX
Plumbing to drain
NOT PROVIDED
Install 3-AAA batteries
to #Umbrella Cap;
connect to Power
Supply
Connect #4 to #3; Flow
Meter Assembly should
be placed on the Outlet
Side. (Note the ow
direction arrow on the
meter body.)
HAND TIGHTEN ONLY
Connect #5 Bypass
to #4
HAND TIGHTEN ONLY
Use either part of #6
for connecting your
plumbing to the system
HAND TIGHTEN ONLY
1 5
6
7
2
3
4
Flow Meter should be
placed on the Outlet
Side. Note the flow
direction arrow on the
meter body.
To Power Supply
INLET OUTLET
NOTE: Flow direction arrows on bypass are
incorrect for this filter application. Plumb
unit opposite of arrows.
1
3
2
7
6
TEFLON TAPE THREADS
Do Not Overtighten
DRAIN VALVE
8
4
5
This system conforms to NSF/ANSI 53 for the specic performance claims veried and substantiated by test data. Performance
claims are based on independent lab results and manufacturer’s internal test data*. Actual performance is dependent on inuent
water quality, ow rates, system design and applications. Your results may vary. Performance claims are based on a complete
system, including a lter, housing, and connection to a pressurized water source. This lter must be operated according to the
system’s specications in order to deliver the claimed performance. It is essential to follow operational, maintenance, and lter
replacement requirements, as directed for each application, for this lter and system to perform correctly. Read the Manufacturer’s
Performance Data Sheet accompanying the system and change the lter as suggested. The contaminants or other substances
removed or reduced by this water lter are not necessarily in all users’ water.
If this or any other system is installed in a metal (conductive) plumbing system, i.e. copper or galvanized metal, the plastic
components of the system will interrupt the continuity of the plumbing system. As a result any errant electricity from improperly
grounded appliances downstream or potential galvanic activity in the plumbing system can no longer ground through contiguous
metal plumbing. Some homes may have been built in accordance with building codes, which actually encouraged the grounding
of electrical appliances through the plumbing system. Consequently, the installation of a bypass consisting of the same material
as the existing plumbing, or a grounded “jumper wire” bridging the equipment and reestablishing the contiguous conductive
nature of the plumbing system must be installed prior to your systems use.
DO NOT USE extra lubricants, unapproved sealants and tools to tighten hand tightened only parts. Use of tools other than hand
tighten only parts voids warranty. Testing was performed under standard laboratory conditions; actual performance may vary.
Flush the system and change the lter as suggested. The contaminants or other substances removed or reduced by this water
lter are not necessarily in all users’ water.
Minimum Operating Temperature 34 F / 1 C
Maximum Operating Temperature: 120 F / 50 C
Minimum Operating Pressure: 20 psig / 1.38 bar
Maximum Operating Pressure: 125 psig / 8.6 bar
Electrical Requirements: Grounded & Unswitched 115 V outlet and 3-AAA Batteries
Filter Replacement Operating Instructions: New cartridges must be ushed for a minimum of
10 minutes prior to use. System and installation to comply with state and local laws and regulations.
Do not use with water that is microbiologically unsafe or unknown quality without adequate
disinfection before or after the system. Systems certied for cyst reduction may be used on
disinfected waters that may contain lterable cysts.
Manufactured from NSF/ANSI standard 61 and California Prop 65 Compliant certied coconut shell
carbon and raw materials.
1. Filter housing
2. Bottom Inlet/Outlet cap assembly
3. Vertical elbow
4. Flow Meter Assembly
5. Bypass manifold
6. Straight or 90-degree Angled In/Out 1” MNPT plumbing connectors
7. 3/8” PEX Drain valve assembly with shut-off
8. Umbrella Cap with PCB assembly and battery backup
NOT SHOWN: Power Supply
CTA0840BBBKP5-04C00
CT-INOUTASSY
CT-VERTICALELBOW
CT-CTMETERASSY
CT-BPMANIFOLD
CT-1MNPTELBOWSET
CT-38DRAINVALVEJG
CT-PCBUMBRELLA
CT-POWERSUPPLY
PART IDENTIFICATION PART NUMBER
SIMPLE ASSEMBLY INSTRUCTIONS
The system and installation must comply with state
and local laws and regulations.
PIONEER™SPECIFICATIONS
PIONEER
NAME AND
PART NUMBER
PEAK FLOW &
% REDUCTION
OF LEAD
CHLORINE/CHLORAMINE TASTE
AND ODOR REDUCTION CAPACITY(*)
PRESSURE
DROP
SPEC
PIONEER™
System
CTA0840BBBKP5-04C00
REPLACEMENT CARTRIDGE FILTERS ARE LISTED AS PIONEER™ 0.5 Micron High Capacity Carbon Block // PART NUMBER: CT-05-CB-AMYCL
9 psid
@ 4.51 GPM
8 GPM (30.2lpm) @
99.62% reduction
(*) >88,000 gallons
at 8 GPM (333,116
Liters @ 30.2lpm)
>300,000 gallons @ 15 GPM (1,135,533 Liters @ 56.8 lpm)
with greater than 90% reduction, estimated capacity using
2ppm of free chlorine.
>150,000 gallons @ 8 GPM (567,812 Liters @ 30.3 lpm)
with greater than 85% reduction, estmated using 3ppm
of chloramine.
*Claims are not performance tested or certied by IAPMO or NSF. Performance claims are based on independent laboratory and manufacturer’s internal test data.
Actual performance is dependent on inuent water quality, ow rates, system design and application. Results may vary.
SIZE &
MICRON
RATING
RATED CAPACIT Y
& FLOW RATE
8” x 40”
0.5
Lead Reduction and PFOA/PFOS
100,000 gallons @ 4.51 GPM
(378,541 Liters @ 17.1 lpm)
@ 99.62% lead reduction
@ 97.9% PFOA/PFOS reduction

67
The overall purpose of this device is to receive a water meter input, and totalize the amount of water that passes through the meter. When there is ow through the
water meter, the lights ash at a rate that increases with the water ow rate. When the total amount of water owed reaches within 10% of a pre-selected amount
the totalizer turns yellow, when the total amount reaches the pre-selected amount the totalizer turns red.
Power
This unit is to be powered using +12VDC. The power input is a wire tail with a 2.5mm, center positive barrel jack.
The totalizer has a battery backup. The battery backup uses 3 AAA size batteries. The battery holder is a part of the PCB assembly and can be accessed by removing
the lid to the cartridge lter. Battery life will vary based on water ow when running on battery mode and type of batteries used. With high continuous ow, the
batteries are expected to last approximately 14 days. With no ow the batteries are expected to last approximately 6 months.
Operation
Water Meter
The totalizer keeps track of the gallons using a water meter. The water meter is a turbine style meter with a magnetic pickup that sends a pulse to the electronics
for every revolution of the meter turbine. The meter turbine is removable for inspection and cleaning. Make sure water is bypassed or turned off when removing
the meter for maintenance. The meter has a three pin plug that connects to the electronic board.
LEDs
Normal colors for the LEDs are Green, Yellow and Red. Depending on the Totalizer value.
• Green = 0 – 90% of the programmed totalizer maximum
• Yellow = 90 – 100% of the programmed totalizer maximum
• Red >= 100% of the programmed totalizer maximum
If there is ow the LEDs should alternately turn off in the following pattern: 1-2-3-2 (repeat). The frequency that they turn off is linearly correspondent to the ow
rate being received from the water meter. For every 1 revolution from the meter, the LED pattern should be incremented to turn off the next LED. If there are no
pulse edges for 2 seconds, all the LEDs will turn on solid.
If the battery is determined to be low, the middle LED (#2) will turn White. The battery is checked only once an hour to minimize the battery drain from checking
the voltage.
Pushbutton
The pushbutton allows for the totalizer to be reset as well as the maximum value to be programmed.
To reset the totalizer, the user should press and hold the button for 3 seconds. When the totalizer is reset LEDs should ash green 3 times to conrm that it is reset.
The push button allows the unit to be programmed for the total gallons limit. It can be programmed for the range of 10,000 gals. – 990,000 gals.
To program the maximum value using the push button: Press and hold the button while powering up the board (either battery power or 12VDC power). Once the
board is powered LED 1 (left LED) will represent 100,000’s place and should be green. LED 2 (middle LED) will represent 10,000’s place and should be blue. Both
LEDs will be ashing at 1 Hz the number of ashes that corresponds to the current setting for that digit placeholder. To indicate the start of the ash sequence both
LEDs should ash white for 1 second, then ash the appropriate number of times. Once both are done wait 2 seconds and repeat. Below, Figure 1, is an example.
Serial Port
The serial port allows for quick and efcient programming through a basic terminal type interface. The board responds with a message when the enter key is
pressed:
Totalizer Current Total: 0 gallons
Totalizer Current Max. Setting: 250,000 gallons
(Send ‘r’ to reset)
( ## to enter new setting in 10,000s [valid range 0-99])
>:
Consult the manufacturer for more details on connecting to the boards serial port.
Power Monitoring and Battery Mode
The board monitors the 12Vdc power and the battery power. If there is a power failure and no batteries are installed, the current totalizer value will be saved to
non-volatile memory. When power is resumed, the totalizer count will resume from when it had previously lost power.
The LEDs should shut off during battery mode. If the totalizer is to the yellow or red state or if the battery voltage gets low, the LEDs will ash on in the appropriate
colors for 0.125 seconds every 4 seconds. If the push button is pressed in battery mode, the LEDs will turn on for 4 seconds and then return to battery mode.
WATER TOTALIZER NOTIFIER
THIS WARRANTY EXCLUDES THE FOLLOWING:
• Damage caused by improper installation, operation or care.
• Damage caused by chemical attack, environment, accident, re, ood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone, chloramines
and other related components), alteration, installation or operation contrary to the printed instructions, or by the use of accessories or components which do not meet ENPRESS’s
specications, including the use of a replacement element not manufactured or supplied by ENPRESS LLC. Refer to the specications section in the Installation and Operating manual
for approved application parameters.
• Modication or alteration by other than ENPRESS LLC employees.
• Rubber type parts and normal wear items i.e. “O” rings, etc…
• Any costs of labor or expenses expended in the removal and/or installation of unit, or any surrounding device.
• Altering or removing the ENPRESS LLC information label.
• Use of non ENPRESS LLC approved cartridges, lters, or replacement parts with the appropriate systems or vessels.
• Non-use of supported piping for plumbing connections to In/Out connections.
• Replacement of water lter cartridge due to water pressure that is outside the specied operating range or due to excessive sediment in water supply; or replacement with non-
authorized replacement cartridge.
• Service trips to installation site to train user on how to use product
• Improper installation
• Failure of product if it is abused, misused, or used for other than the intended purpose
• Replacement of water lter cartridge due to water pressure that is outside the specied operating range or due to excessive sediment in water supply; or replacement with non-
authorized replacement cartridge
• Damage to product cause by accident, re, oods or acts of God
• Incidental or consequential damage caused by possible defects with any other equipment not covered by this warranty
SPECIAL NOTICES:
• Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after installing lter or system.
• Systems certied for Cyst reduction may be used on disinfected water that may contain lterable cysts.
• Any system this lter is installed in must be maintained according to manufacturer’s instructions, including replacement of lter cartridges.
• Contaminants or other substances removed or reduced by this water lter cartridge are not necessarily in your water.
• Note that while testing was performed under standard laboratory conditions, actual performance may vary. Systems using these lters must be installed and operated in accordance
with manufacturer’s recommended procedures and guidelines.
ENPRESS LLC- PIONEER™ System - Limited Warranty
• ENPRESS LLC warrants its line of ENPRESS PIONEER™ ltration systems, to be free of defects in material and workmanship for a period of one year, and replacement PIONEER™
lters for a limited thirty-day warranty, from the date of purchase. This warranty is extended to original purchaser, by authorized OEM customers. Use of this product constitutes Buyer’s
acceptance of this Limited Liability.
• This warranty does not cover any equipment purchased for use in applications in which the product is not suited. It is the responsibility of the buyer to determine if a product is suitable
for a particular application.
• Our obligations under this warranty are limited to the repair or replacement (at ENPRESS’s sole discretion) of the failed parts of the water treatment unit manufactured by ENPRESS, and
we assume no liability whatsoever for direct, indirect, incidental, consequential, special, general or other damages.
• We assume no liability for the determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us.
• We assume no liability and extend no warranties, expressed or implied, for the use of this product with a non-potable water source or a water source which does not meet the conditions
for use described in the owner’s guide or performance data sheet for the product.
• The warranty provided herein applies, only when used within the product specications and service life, from the date of installation, beyond which ENPRESS LLC is absolved of any
and all liability for any use of the product. There are no other warranties, either of merchantability or tness, either expressed or implied. Some states do not allow exclusion or limitation
of incidental or consequential damages. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state, or country to country. To know
what your legal rights are, consult your local or state consumer affairs ofce, your state’s Attorney General, or your national equivalent for international users.
WARRANTY
Service under this warranty is to be provided by the distributor/installer who sold the unit to
the user. If the distributor is unable to provide warranty service, contact:
ENPRESS, LLC. | 34899 Curtis Blvd., Eastlake Ohio 44095
Phone [phone] | Fax [phone] | [e-mail]
A Returned Goods Authorization (RGA) number must be received from the above ofce and
placed on all shipments to and in correspondence with ENPRESS LLC.
Please be prepared with the following information:
Model number
and serial number.
Date of
installation.
Name of
installer.
Nature of
problem.
Your address and
contact information
1 2 3 4 5
Figure 1
To change the maximum gallons setting, press and hold the
button for 1 second. LED1 should turn solid green, LED2
should turn off and LED3 should ash green the number of
times that corresponds to the current setting. Pressing the
button for less than 1 second would increment the value,
rolling over from 9 to 0. Below, Figure 2, is an example of the
LEDs in this mode.
Figure 2
To save the setting for the 100,000s place and begin editing
the 10,000s place press and hold the button for greater
than 1 second. LED1 should turn off, LED 2 should turn
solid blue, and LED3 should ash blue the number of times
that corresponds to the current setting. Again, pressing the
button for less than 1 second would increment the value,
rolling over from 9 to 0. Below, Figure 3, is an example of the
LEDs in this mode.
Figure 3
To save the setting for the 10,000s place and exit editing
mode and return to the mode in Figure 1 press and hold the
button for greater than 1 second. This would also save the
current setting into internal EEPROM memory.
LIMITED LIABILITY - ENPRESS LLC makes no warranties of any kind, expressed or implied, statutory or otherwise, and expressly disclaims all
warranties of every kind, concerning the product, including, without limitation, warranties of merchantability and tness for a particular purpose,
except that this product should be capable of performing as described in this product’s data sheet. ENPRESS LLC’s obligation shall be limited
solely to the refund of the purchase price or replacement of the product proven defective, in ENPRESS LLC’s sole discretion. Determination
of suitability of this product for uses and applications contemplated by Buyer shall be the sole responsibility of Buyer. Use of this product
constitutes Buyer’s acceptance of this Limited Liability.

NOTES
MANUFACTURED BY CERTIFICATIONS
All information contained herein is the property of ENPRESS LLC. ENPRESS LLC makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and tness for a particular purpose. ENPRESS LLC shall not be liable
for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing,
performance, or use of this material. The information is provided “as is” without warranty of any kind and is subject to change without notice.
This document contains proprietary information which is protected by copyright. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of ENPRESS LLC. © Copyright 2018 ENPRESS LLC. All rights reserved.
© ENPRESS LLC 2018 | PIONEER™is an ENPRESS Filtration Technology | 2019-0103
ENPRESS®, ONE®, WATER FILTRATION SIMPLIFIED®AND PIONEER™ are trademarks of ENPRESS, LLC.
For more information, visit enpress.com or
oneltration.com
POWERED BY
Where Innovation Flows™
This ENPRESS pressure vessel
is tested and certied by NSF
International against NSF/ANSI
Standard 44 and 61 for materials and
structural integrity requirements
COMPONENT
FOR PURCHASES MADE IN IOWA
This form must be signed and dated by the buyer and seller prior to the consummation of this sale. This form should be
retained on le by the seller for a minimum of two years.
Buyer’s Name (printed) Buyer’s Signature Date
Seller’s Name (printed) Seller’s Signature Date
This ENPRESS system is certied
by IAPMO R&T against NSF/ANSI
Standards 53 and P473 (also CSA
B483.1) for the reduction of claims
specified on the performance
data sheet.

PIONEER™SPECIFICATIONS
PIONEER
NAME AND
PART NUMBER
PEAK FLOW &
% REDUCTION
OF LEAD
CHLORINE/CHLORAMINE TASTE
AND ODOR REDUCTION CAPACITY (*)
PRESSURE
DROP
SPEC
PIONEER™
System
CTA0840BBBKP5-04C00
REPLACEMENT CARTRIDGE FILTERS ARE LISTED AS PIONEER™ 0.5 Micron High Capacity Carbon Block // PART NUMBER: CT-05-CB-AMYCL
9 psid
@ 4.51 GPM
8 GPM (30.2lpm) @
99.62% reduction
(*) >88,000 gallons
at 8 GPM (333,116
Liters @ 30.2lpm)
>300,000 gallons @ 15 GPM (1,135,533 Liters @ 56.8 lpm)
with greater than 90% reduction, estimated capacity using
2ppm of free chlorine.
>150,000 gallons @ 8 GPM (567,812 Liters @ 30.3 lpm)
with greater than 85% reduction, estmated using 3ppm
of chloramine.
*Claims are not performance tested by IAPMO or NSF. Performance claims are based on independent laboratory and manufacturer’s internal test data.
Actual performance is dependent on inuent water quality, ow rates, system design and application. Results may vary.
Model Number of the system in which the lter component is to be used with CTA0840BBBKP5-04C00
SIZE &
MICRON
RATING
RATED CAPACIT Y
& FLOW RATE
8” x 40”
0.5
Lead Reduction and PFOA/PFOS
100,000 gallons @ 4.51 GPM
(378,541 Liters @ 17.1 lpm)
@ 99.62% lead reduction
@ 97.9% PFOA/PFOS reduction
ENPRESS®, ONE®, WATER FILTRATION SIMPLIFIED®AND PIONEER™ are trademarks of ENPRESS, LLC.
© ENPRESS LLC 2018 | PIONEER™is an ENPRESS Filtration Technology | 2019-0103
If you have any questions regarding your water lter, contact your local dealer, OEM, or the manufacturer at the following:
For more information, visit enpress.com or oneltration.com
THANK YOU FOR CHOOSING PIONEER™
POWERED BY
Where Innovation Flows™
PERFORMANCE
Performance claims are based on independent lab results
and manufacturer’s internal test data*. Actual performance is
dependent on inuent water quality, ow rates, system design
and applications. Your results may vary. Performance claims
are based on a complete system, including a lter, housing,
and connection to a pressurized water source. This lter must
be operated according to the system’s specications in order
to deliver the claimed performance. It is essential to follow
operational, maintenance, and lter replacement requirements,
as directed for each application, for this lter and system to
perform correctly. Read the Manufacturer’s Performance
Data Sheet accompanying the system and change the lter as
suggested. The contaminants or other substances removed or
reduced by this water lter are not necessarily in all users’ water.
IMPORTANT
DO NOT USE extra lubricants, unapproved sealants and tools
to tighten hand tightened only parts. Use of tools other than
hand tighten only parts voids warranty. Testing was performed
under standard laboratory conditions; actual performance may
vary. Flush the system and change the lter as suggested. The
contaminants or other substances removed or reduced by this
water lter are not necessarily in all users’ water.
WARRANTY
LIMITED LIABILITY - ENPRESS LLC makes no warranties of any
kind, expressed or implied, statutory or otherwise, and expressly
disclaims all warranties of every kind, concerning the product,
including, without limitation, warranties of merchantability and
tness for a particular purpose, except that this product should be
capable of performing as described in this product’s data sheet.
ENPRESS LLC’s obligation shall be limited solely to the refund
of the purchase price or replacement of the product proven
defective, in ENPRESS LLC’s sole discretion. Determination of
suitability of this product for uses and applications contemplated
by Buyer shall be the sole responsibility of Buyer. Use of this
product constitutes Buyer’s acceptance of this Limited Liability.
CERTIFICATIONS
MANUFACTURED BY
This ENPRESS pressure vessel
is tested and certied by NSF
International against NSF/ANSI
Standard 44 and 61 for materials and
structural integrity requirements
COMPONENT
EPA Est. 092577-OH-001
ENPRESS, LLC. | 34899 Curtis Blvd., Eastlake Ohio 44095 | Phone [phone] | Fax [phone] | [e-mail]
SUBSTANCE
INFLUENT CHALLENGE
CONCENTRATION
(MG/L)
MAXIMUM PERMISSIBLE
PRODUCT WATER
CONCENTRATION (MG/L)
Lead
Cyst
PFOA/PFOS
0.15 +/- 10%
minimum 50,000/L
1.5 +/- 10%
0.01
99.95%
0.07
Minimum Operating Temperature 34 F / 1 C
Maximum Operating Temperature: 120 F / 50 C
Minimum Operating Pressure: 20 psig / 1.38 bar
Maximum Operating Pressure: 125 psig / 8.6 bar
Electrical Requirements: Grounded & Unswitched 115 V outlet and
3-AAA Batteries
Filter Replacement Operating Instructions: New cartridges must be
ushed for a minimum of 10 minutes prior to use. System and installation
to comply with state and local laws and regulations.
Do not use with water that is microbiologically unsafe or unknown
quality without adequate disinfection before or after the system.
Systems certied for cyst reduction may be used on disinfected waters
that may contain lterable cysts.
Manufactured from NSF/ANSI standard 61 and California Prop 65
Compliant certied coconut shell carbon and raw materials.
NSF/ANSI
STANDARD
53
53
P473
This ENPRESS system is certied
by IAPMO R&T against NSF/ANSI
Standards 53 and P473 (also CSA
B483.1) for the reduction of claims
specified on the performance
data sheet.
This system has been tested for the reduction of the
substances listed below. The concentration of the indicated
substances in water entering the system was reduced to
a concentration less than equal to the permissible limit for
water leaving the system, as specied in NSF/ANSI 53 and
P473. Minimum substance reductions are as follows:

1. Turn off the water supply to the system by shutting off the inlet and outlet valves on the bypass.
2. (Optional) Install a 3/8” PEX tubing hose to the provided John Guest® tting and shut-off that
connects to the inlet side of the ltration system. Run the hose to a oor drain or bucket, and use to
drain sediment or to aid in lter removal during change-out.
3. Remove Umbrella Cap on the top of the vessel. Replace the 3-AAA batteries with new batteries.
Push and hold the reset button on the metered board for 3 seconds to reset the totalizer. When the
totalizer is reset the LED lights will ash green 3 times to conrm that it is reset.
4. Depressurize the system by pushing down on the red depressurization button on the top cap of the
system. Keep the button pushed down until all the air or water pressure is completely released.
5. Push down the top cap with both hands to unseat the retaining ring.
6. Remove the retaining ring by carefully grasping the handle and pulling inward, then upward. The
retaining ring should slide completely out of the groove.
7. Remove the top cap of the system by lifting up on the top handles, remove old lter.
8. Open the John Guest® tting and shut-off , and ush out the bottom of the system.
9. Look down into the tank assembly, and you should see a small opening centered in the bottom of
the tank.
10. Remove packaging from the new lter, place the new cartridge into the tank with the double o’ring
facing down.
11. Position the cartridge so that it is aligned with the bottom, center opening.
12. Press down on the cartridge so that the double o’ring seal moves into place within the bottom,
center opening.
13. Reposition the Top Cap into its original location.
14. Reattach the top tank Snap Ring, pull up on the Top Cap to seat o-rings.
15. (If completed Step 2, then…) Close the John Guest® tting and shut-off.
16. Turn the water supply on, opening the inlet and outlet valves on the bypass.
17. Relieve the system of air in the tank as the system lls with water, by pushing down on the red
depressurization button on the top cap of the system. Keep the button pushed down until all the air
pressure is completely released, and water comes out of the red depressurization button.
18. Release the red depressurization button.
19. Replace the Umbrella cap to the top of the system.
20. Check for leaks.
21. Flush the new cartridge per its installation instructions in the installation manual.
22. During ush, conrm green LED lights are ashing with owing water.
REPLACING THE CARTRIDGE
#3 UMBRELLA CAP
& LED LIGHTS
The Real-time Dynamic LED System monitors water and ow rate and provides a visual color-coded
notication to the homeowner, letting them know when to replace their lter.
*Meter preset at 100,000 gallons; see Installation Manual for resetting when the cartridge is replaced.
*Three AAA batteries not included, for battery back-up. Change annually with lter change-out.
*Refer to Installation Manual from proper installation and product service guidelines.
EASY TO UNDERSTAND LED REPLACEMENT NOTIFICATIONS
GREEN
FILTER
GOOD
YELLOW
CHANGE
SOON
10%
FILTER
LIFE
REMAINING
RED
CHANGE
NOW
PIONEER uses state-of-the-art snap-ring technology to eliminate the need for cumbersome tools.
Homeowners can easily replace the lter in their PIONEER system by followng a few simple steps.
EASY FILTER REPLACEMENTS AND NO TOOLS REQUIRED
LIFT TOP CAPPRESS THE RED PRESSURE RELIEF VALVE & PULL SNAP-RING
Flow Meter should be
placed on the Outlet
Side. Note the flow
direction arrow on the
meter body.
To Power Supply
INLET OUTLET
NOTE: Flow direction arrows on bypass are
incorrect for this filter application. Plumb
unit opposite of arrows.
1
3
2
7
6
TEFLON TAPE THREADS
Do Not Overtighten
DRAIN VALVE
8
4
5
ELLC 2019-0103

IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a
combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the
supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in
the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product
acceptance by Authorities Having Jurisdiction.
This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material,
manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of
non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing.
Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc.
Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.
This certificate is not evidence of current listing. To verify listing status, visit the IAPMO R&T
Product Listing Directory at pld.iapmo.org
Effective Date: April 2019 Void After: April 2024
Product: Water Treatment Product - Health Effects File No. W-9981
Issued To: Enpress Llc.
34899 Curtis Blvd.
Eastlake, OH 44095
Identification: The product or packaging shall be marked with the model number, name and
address of manufacturer, functional description of system, max operating
temperature, max working pressure, a statement noting that the system
conforms to NSF/ANSI 53 for the specific performance claims verified and
substantiated by test data, as well as the IAPMO UPC® Shield certification
mark.
In the case of private labelling, the product packaging shall be marked with
the model number and the name, trademark, or other mark of the customer for
whom the fitting was manufactured.
Characteristics: The point-of-use and point-of-entry systems addressed by this Standard
are designed to be used for the reduction of specific substances that
may be present in drinking water (public or private) which are
considered health hazards.
Certification demonstrates that all materials safety and structural
integrity (as applicable) requirements have been met.

Void After: April 2024
Product: Water Treatment Product - Health Effects File No. W-9981
Issued To: Enpress Llc.
To be used in accordance with the manufacturer's instructions
Products listed on this certificate have been tested by an IAPMO R&T
recognized laboratory. This recognition has been granted based upon the
laboratory's compliance to the applicable requirements of ISO/IEC
17025.
Products are in compliance with the following code(s):
Uniform Plumbing Code (UPC®)
Products are in compliance with the following standard(s):
NSF/ANSI 53-2017

MODELS:
Model Number Replacement
Component
Capacity
(Gallons)
Flow
Rate
(GPM)
Reduction Claims
Product Type: Point-of- ntry
CTA0838BBxxP5-04Cyyy 1CT-05-CB-AMCYL-38 93,250 4.21 Lead, Cyst
CTA0840BBxxP5-04Cyyy 1CT-05-CB-AMCYL 100,000 4.51 Lead, Cyst
CTA0842BBxxP5-04Cyyy 1CT-05-CB-AMCYL-42 106,750 4.82 Lead, Cyst
1 xx can e any com ination of num ers and letters and references the outer tank color.
yyy can e any com ination of num ers and letters and references an internal designation
not related to certification.
Page 3 of 3
This certificate is not evidence of current listing. To verify listing status,
visit the IAPMO R&T Product Listing Directory at pld.iapmo.org
Void After: April 2024
Product: Water Treatment Product - Health Effects
Issued To: Enpress Llc.
File No. W-9981

IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a
combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the
supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in
the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product
acceptance by Authorities Having Jurisdiction.
This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material,
manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of
non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing.
Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc.
Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.
The most updated information on this Certificate of Listing is available online at pld.iapmo.org
Effective Date: January 2019 Void After: January 2020
Product: Drinking Water Treatment Units – PFOA & PFOS File No. W-11467
Issued To: Enpress Llc
34899 Curtis Blvd.
Eastlake, OH 44095
Identification: The product packaging shall be marked with the model number and
a)the manufacturer's recognized name, trademark, or other mark; or
b)in the case of private labelling, the name, trademark, or other mark of
the customer for whom the fitting was manufactured.
c)a functional description of the system (e.g., chemical reduction)
d)maximum operating temperature in degrees C (degrees F)
e)maximum working pressure in kPa (psig)
f)for activated carbon systems: "Do not use with water that is
microbiologically unsafe or of unknown quality without adequate disinfection
before or after the system."
Characteristics: The systems addressed by this standard are designed to be used to reduce PFOA
and PFOS that may be present in drinking water (public or private), which are
considered health hazards.
Products are to be installed in accordance with the manufacturer's
instructions and local codes.

Void After: January 2020
Product: Drinking Water Treatment Units – PFOA & PFOS File No. W-11467
Issued To: Enpress Llc
Products listed on this certificate have been tested by an IAPMO R&T
recognized laboratory. This recognition has been granted based upon the laboratory's
compliance to the applicable requirements of ISO/IEC 17025.
Products are in compliance with the following standard(s):
NSF P473-2016