Enterasys VH-STACK User manual

VERTICAL HORIZON FAST ETHERNET SWITCH
STACKING MODULE
Enterasys’s VH-STACK Stacking Module can be used
to stack up to four VH-2402S switch units. Running at
a bandwidth of over 4 Gbps, these modules provide a
common interface to the attached switches, allowing
the stack to function and be managed as a single
device.
System and Port Status LEDs
LEDs are provided on the front panel of the switch.
These LEDs can be used to verify if the stack is
functioning properly. The following table details the
indicator functions provided by the VH-2402S:
Port and System Status LEDs
LED Condition Status
Power On Switch is receiving power.
RDP On Redundant power is on, and in
backup or active mode.
Off Redundant power is off or has failed.
Mgmt On Agent is operational.
RJ-45 Ports
Link On Port has established a valid network
connection
Yellow Valid 10 Mbps connection.
Green Valid 100 Mbps connection.
Flashing Port has been partitioned due to an
abnormal network condition, or
manually disabled.
Activity
1
On Traffic is passing through the port.
FDX
1
On Port has been set to full duplex.
FC
1
On Flow control enabled.
Module Ports
Status On A module is installed in this slot.
Activity Flashing Traffic is passing through the port
1: Use the Mode Select button to select LED display mode.
2: There is no LED for indicating stacking status.
INSTALLING THE MODULE
CAUTION: The VH-STACK Stacking Module is
designed for VH-2402S switches only. Do not try to
install these modules in any other units.
The VH-STACK Stacking Module installs in the lower-
left slot on the rear panel of the VH-2402S switch. Do
not install this module in any other slot. To install the
module, follow the instructions below.
Equipment Checklist
After unpacking the Stacking Module, check the
contents of the box to be sure you’ve received the
following items:
•One VH-STACK Stacking Module
•One Stacking Cable
•This document
Handling the Module
CAUTION: The VH-STACK Stacking Module can
easily be damaged by electrostatic discharge.
To prevent electrostatic damage, observe the following
guidelines:
•Do not remove the module from its packaging until
you are ready to install it.
•Do not touch any of the module’s pins, connectors
or components.
•Hold the module only by its edges or front panel.
•Wear an anti-static wristband connected to a
suitable earth ground whenever handling the
module.
•Store or transport this module only in appropriate
anti-static packaging.
Instructions
CAUTION: The switch must be powered off before
installing or replacing any module.
1. Power off the switch: Disconnect the AC power
cord from the switch. If a redundant power unit
(RPU) is present, disconnect its DC cable
connection to the switch.
2. Remove network cables: If you are replacing a
module, remove the cable attached to the port on
the module.
3. Loosen the screws on the installed module or
slot faceplate: Using your fingers or a flathead
screwdriver, turn the screws securing the module
(or faceplate) in the lower-left slot in a counter-
clockwise direction until they are free of the
chassis. Be sure not to completely remove the
screws from the module or faceplate.
4. Remove the installed module or faceplate:
Firmly pull on the screws until the module is free of
the switch. Carefully slide the module straight out of
the slot.
Keep the original faceplate for future use. If you
should remove the module, replace the faceplate to
prevent dust and debris from entering the unit and
to maintain proper air flow.
5. Insert the new module into the switch: Holding
the new module with the text on the front panel
upright, carefully slide the module into the switch
slot and press gently until it snaps into place. Be
sure the new module’s front panel is flush with the
switch panel.
6. Secure the new module: Secure the new module
in place by screwing the attached screws clockwise
into the switch’s chassis. Tighten them enough to
secure the module, but not so tight as to prevent
them from being unscrewed by hand.
7. Connect the stack cables: Attach one end of the
stacking cable to the stack connector labeled
“DOWN”on the top device, and the other end to
the connector labeled “UP”on the next lower
device. Repeat this step until all the devices have
been connected.
8. Power on the switch: Reconnect the previously
removed power sources to the switch. (Note that
the Management Module in the bottom switch will
become the master.) The front-panel LEDs on the
switches should indicate their status. Refer to the
table of LEDs in this guide for a description of the
LED indications. If the stack is not functioning
properly, see “Troubleshooting”below.
More details concerning connection options and
network applications can be found in the
VH-2402S Installation Guide. Information on managing
the stack can be found in the Management Guide that
is included with the base unit.
TROUBLESHOOTING
If you experience any problems with the module, check
the following items before contacting Enterasys’s
Technical Support:
•Ensure that all the switches in the stack are
powered up.
•Ensure that the devices attached to the stack are
powered up and operating correctly.
•Ensure that the Stacking Modules are properly
seated in their slots.
•Check the connectors on both ends of the stack
cable to be sure they are properly engaged. Tighten
the thumb screws on the cable connectors to
ensure a good connection.

SPECIFICATIONS
Ports
2 68-pin SCSI connectors
Cab
l
e
T
ype
SCSI Type 4
Size
4.82 x 3.57 x 1.08 in.
(12.25 x 90.70.5 x 2.74 cm)
Power Consumption
2W maximum
T
emperature
Operating: 32°to 122°F (0°to 50°C)
Storage: -40°to 158°F (-40°to 70°C)
Humidity
Operating: 5% to 95%
Compliances
CE Mark
Emissions
FCC Class A
EN55022 (CISPR 22) Class A
VCCI Class A
C-Tick
Immunity
IEC 1000-4-2/3/4/6
Vertical Horizon
VH-STACK
STACKING MODULE
QUICK INSTALLATION GUIDE
9033633
E092000-R01
150525-102
NOTICE
Enterasys Networks reserves the right to make changes in specifications and other
information contained in this document without prior notice. The reader should in
all cases consult Enterasys Networks to determine whether any such changes have
been made.
The hardware, firmware, or software described in this manual is subject to change
without notice.
IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY
INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS)
ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION
CONTAINED IN IT, EVEN IF ENTERASYS NETWORKS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF
SUCH DAMAGES.
2000 by Enterasys Networks, Inc., P.O. Box 5005, Rochester,NH 03866-5005
All Rights Reserved
Printed in Taiwan, R.O.C.
Order Number:9033633 October 2000
Enterasys, Enterasys Networks, and Vertical Horizon are trademarks or registered
trademarks of Enterasys Networks, Inc.
Microsoft, Windows, Windows 95, Windows 98, and Windows NT are either
trademarks or registered trademarks of Microsoft Corporation.
Netscape and Netscape Navigator are trademarks of Netscape Communications
Corporation.
All other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE:This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment uses,
generates, and can radiate radio frequency energy and if not installed in accordance
with the operator’s manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause interfer-
ence in which case the user will be required to correct the interference at his own
expense.
WARNING:Changes or modifications made to this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la class A prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministère des Communica-
tions du Canada.
VCCI NOTICE
EC CONFORMANCE DECLARATION
European contact: Enterasys Networks Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG13 2PZ, England
This information technology product complies with ISO/IEC Guide 22 and
EN45014. It conforms to the following specifications:
EN55022(1988)/CISPR-22(1985) Class A
EN50082-1: IEC 1000-4-2, 3, 4, 6
This information technology product complies with the requirements of
the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/
EEC and carries the CE Mark accordingly.
Only qualified personnel should perform installation
procedures. CONNECTIVITY GUIDELINES
snoitacificepSdnasepyTelbaC
elbaCepyThtgneL.xaMrotcennoC
T-esaB01PTUmho-0015,4,3.taC).tf823(m00154-JR
XT-esaB001PTUmho-0015.taC).tf823(m00154-JR
XF-esaB001norcim521/5.26ro521/05
rebifedomitlumeroc
xelpudflaH).tf4.153,1(m214TSroCS
xelpudlluF)selim42.1(mk2TSroCS
rebifedom-elgnis521/01)tf404,61(mk5TSroCS
XS-esaB0001norcim521/5.26ro521/05
rebifedomitlumeroc
gniwollofehteeS
elbat
TSroCS
XL-esaB0001FMSroFMMgniwollofehteeS
elbat
TSroCS
snoitacificepSrebiFXS-esaB0001
retemaiDrebiF htdiwdnaBladoM egnaR
norcim521/5.26 mk/zHM061)m022-2(tf227-7
mk/zHM002)m572-2(tf209-7
norcim521/05 mk/zHM004)m005-2(tf1461-7
mk/zHM005)m055-2(tf5081-7
snoitacificepSrebiFXL-esaB0001
retemaiDrebiF htdiwdnaBladoM egnaR
FMM521/5.26 mk/zHM005)tf5081-7(m055-2
FMM521/05 mk/zHM004)tf5081-7(m055-2
mk/zHM005)tf5081-7(m055-2
FMS521/01A/N)tf404,61-7(mk5-m2
retemaiDkrowteNtenrehtEtsaFmumixaM
epyTretaepeR
rebmuNdna
riaPdetsiwT
XT-ESAB001
rebiF/riaPdetsiwT
XFdnaXT-ESAB001
IssalC1)tf656(m002)tf4.558(m8.062
IIssalC1)tf656(m002)tf6.2101(m8.803
IIssalC2)tf4.276(m502)tf1.907(m2.612
Note: Network diameter is defined as the wire distance between
two end stations in the same collision domain.