Entryvue AC-500 User manual

EntryVue AC-500 Keypad User Manual
Please read this manual carefully before Installation
EM Metal Password Access Controller
3. Technical parameters
4. Administrator operation
(Figure 1)
2. Features
Low power consumption: less than 30mA standby current
Luminous keyboard: keyboard can be operated at night
User capacity: support 2,000 users
Work Voltage：AC&DC9-28V
Static Current：≤30mA
Reading Range：3〜8cm
Capacity: 2000 users
Ambient Temperature：-25℃〜60℃
Ambient Humidity：10%〜90%
Electricity lock output：≤3A
Alarm output：≤20A
Output short circuit protection time：≤100µS
Independent password: open the door with password which
is irrelevant to the access card
User modified password: Users can revise the door
password
Search speed: charge less than 0.1 S.
Output short circuit protection: electric lock or alarm output
circuit within 100 µS when shut down automatically output
Wiegand output: With Wiegand output interface，Wg26
card number or Wg4 buttons output
Usable keyboard delete card number: After card is lost,
usable keyboard delete card,thoroughly eliminate safety
lapses
The demolition alarm: Illegal dismantling machine, built-in
alarm sound buzzer
The bell button and interface: key and circuit segregation,
external any the doorbell.
1. Product Profile
The product is Contact-less inductive card Metal
Password Access Controller.According to the model, it
respectively supports EM, HID, MIFARE three cards, it is
one of the most advanced stand alone access
controllers.
It is designed with unique metal exterior, dexterity
keyboard panel operation, built-in high-grade
microprocessors, strong anti-interference ability. Safety
and reliability are extremely high, it can provide
powerful security for 2,000 users.
It contains strong functions, such as low power
consumption, luminous keyboard, independent
passwords, wiegand output, output short circuit
protection, door magnetic alarm, prevent demolition
alarm, exit button, doorbell interface, level of security
Settings, etc.
The product is widely used in homes, offices, residential
areas and other public places.
Restore factory settings:
Open time：0 ~ 99 seconds (adjustable)
Size：120 *80*25mm
Disconnect the power supply and open the back
cover, use the equipped two feet short-circuit, the
inserting pin, plugged into the machine rear Two short
circuit seat，then the machine buzzes, then take short
circuit, namely the inserting pin for initialization of
success. (Figure 1)
Note: restore factory Settings will not delete user data
Enter administrator operation status:
Press
Administrator the defaultpassword: 999999
#
Administrator password
*

5. User operations
6. Remove alarm operation
*
EntryVue AC-500 Keypad User Manual
EM Metal Password Access Controller
4.1 Modify administrator password:
Press
Note: the administration password is between 6 - 8 numbers.
please be careful when entering.
Automatically adding, the user ID automatically
generated by this machine, the range is 1 - 2000,
and search from small to large.
Note: input ID digits of 1-4 digits, The range is 1 - 2000,
numbers such as 1,01,001,0001 ID number all expressed 1.
4.2 Add user:
4.3 Delete user
4.2.1 Add multiple cards:
#
The new password # Repeat he new password #
0
5.1 Card modify password:
Press
Press
Note: applicable to a card or card-less users, if the
user password is "1234", must use card to modify
Reading card
Old password
Press
4.2.2 Add designated card Number:
, ...,
#
, ...,
Reading card Reading card
1
4.2.5 Add designated ID number and password:
#
Press ...
ID No # password # ID No # password #
1
Press
Eight card number # Eight card number #
1
4.3.1 Delete swipe card
#
Press
4.3.2 Delete Designated card Number：
...
#
, ...,
Reading card Reading card
2
Press
Eight card number # Eight card number #
2
4.2.3 Add designated ID Number swipe card:
#
, ...
,Press
ID number # ID number #Reading card
Reading card
1
4.2.4 Add designated ID number and card number:
#
, ...
,Press
ID number # ID number #Eight card number #
Eight card number #
1
Adding card user will automatically generate a default
password "1234", but this password can not open the door,
the password is only for a user to change to a new password.
Note: applicable to number card users, password and
card are unrelated, input a four digit code, but not "1234"
4.3.3 Delete Designated ID Number：
#
Press
4.3.4 Delete all：
...
#
#
New password
#
Repeat the new password
#
#
ID No # ID No #
2
Press
20000
6.1 External alarm and built-in buzzer alarm at the same time
Swipe or press
Valid card Administrator password #
*
5.2 User ID number modify password
ID No Old password
#
#
New password
#
Repeat the new password
Press , doors open
5.4 Password open：
User password
#
, doors open
(stop alarm)
6.2 Close door alarm tips
Close the door, or swipe card , or input
Valid card
Administrator password #
, Can stop alarm
5.5 Card + Password open：
User password
#
, doors open
5.3 Card open：
Reading card
Reading card
4.7.1 Shielding of the function (factory default)：
#
0~99
4.4 Door opening method setting：
4.4.1 Card open：
4.5 Unlock time setting：
Press
Press
4.4.2 Card + Password open：
3
0
#
#
#
3
2
3
4
#
1
Press
4.4.3 Card or Password open：（Factory default）
Press
Note: The lock time range "0 to 99 seconds ",
the factory default is 5 seconds
4.6 Alarm time setting:
Press
Note: The alarm time ranges from 0 - 3 minutes,
the factory default is 1 minute
#
0
6
Press
Press
4.7.2 Open the function：
#
1
6
Open the function, two possibilities:
4.8.1 Normal mode (factory default)
#
0
7
7
Press
Press
4.8.2 Lock mode：
#
1
The system will lock and alarm after a ten minute
continuous brush of an invalid keycard. The system will
also alarm after a continuous entry of a wrong password.
4.7.2.1 If the door is not closed properly for 1 minute,
the built-in buzzer alarm will sound off.
4.7.2.2 If the doors are unlock for 20 seconds after the
doors are opened, or if the doors are forced to
open, the built-in buzzer alarm will soud off.
4.7 Magnetic Alarm Function setting：
4.8 Security mode setting
5
0~3
7. Acousto-optic instructions
Operation
state
Standby
Buttons
Success
Failure
Into
programming
Set condition
Exit
programming
Unlock
Alarm
Red Light
Slow
flashing
Off
On
On
Slow flash
Off
Fast flashing
Green Light
Off
On
Off
On
Off
On
Off
Buzzer
Di
Di-
DiDiDi
Di-
Di-
Di-
Alarm sound
Note
Indicator is
orange

Line
sequence
1
2
3
4
5
6
7
8
9
10
11
12
13
8. Installation method, lead wire description and Cabling diagram
EntryVue AC-500 Keypad User Manual
EM Metal Password Access Controller
8.1 Installation method
8.3 Cabling diagram
(Figure 2)
When installing on the wall, take notice of the apreture
size of drill to fit the connecting holes, or installed two
exisiting junction boxs plus connection.(Figure 2)
8.1.1
Put the lead wire from bottom shell of the outlet
hole, connect the cables needed. Unused
lines are wrapped with insulating tape to prevent
short circuit.
8.1.2
When complete, Install the front cover to the back
cover, tighten the screws, stabilize the front
cover and back cover.
8.1.3
Ordinary power supply Cabling diagram (Figure 3)
(Figure 3)
8.3.1
8.2 Lead wire description
BELL_A Pink Doorbell button one end
BELL_B Pale
blue
The doorbell button to the
other end
D0 Green WG output line D0
D1 White WG output line D1
Exit button one end (Exit button
the other end connected GND)
Magnetic switch one end
(magnetic switch another end
connected GND)
Power supply 9-28V input
(DC input-)
Relay normally-on end
(Connected positive electric lock+)
Relay Public end, Connected GND
Relay Public end, (Connected
negative electric lock +)
Ac input for machines minus
Power supply 9-28V input
(DC input+)
ALARM Grey Alarm negative (alarm positive
connected +12V)
Marks Color Function description
OPEN
D_IN
AC&DC
AC&DC
NO
COM
NC
GND
Yellow
Brown
Red
Black
Blue
Purple
Orange
Shielding
layer

9. Packing list
EntryVue AC-500 Keypad User Manual
EM Metal Password Access Controller
Access Control Power Supply Cabling diagram (Figure 4)
Notices
8.3.2
(Figure 4)
Name Model/
specification Quantity Note
Metal Password
access controller GAR-3008 1
User manual GAR-3008
1N4007
1
Tapping screws Φ4mm×28 mm 4 Used for
installation fixed
Used for
installation fixed
Stopper Φ6mm×30 mm 4
Star screwdriver Φ20mm×60mm 1
1
Secial
Star screws
LED
Φ3mm×6mm
1
Used between
the front
cover and
back cover
for a fixed
If there is any problem, please return the product to the
factory for maintenance.
Before installing the product on the wall, please check the wiring
or line tube carefully to prevent accidents, such as broken wiring
caused by drilling. Please use saftey goggles when drilling or when
fixing the line clip.
Specifications will likely be different after product upgrades,
no prior notice will be made.