Envirovent energiSava 325 Quick start guide

energiSava® 325
INSTALLATION GUIDE FOR ENGINEER / INSTALLER

1energiSava®325
SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING
THIS UNIT, CALL US ON: 0345 27 27 810
Safety
Important: Read these instructions fully before the installation of this appliance
1. Installationoftheapplianceandaccessories
must be carried out by a qualified and
suitable competent person and be carried
out in clean, dry conditions where dust and
humidity are at minimal levels.
2. This manual covers the installation of the
Heat Recovery Ventilation unit.
3. All wiring must conform to current I.E.E.
Wiring Regulations and all applicable
standards and Building Regulations.
4. Inspect the appliance and electrical supply
cord. If the supply cord is damaged, it
must be replaced by the manufacturer,
their service agent or similarly qualified
persons in order to avoid a hazard.
5. The unit is supplied with a mains rated 3
core flexible cord (PVC sheathed, brown,
blue and green/yellow 0.75mm²).
6. The appliance must be connected to a
local double pole isolation switch with a
contact separation of at least 3mm.
7. The appliance must be earthed.
8. The unit is suitable for 230V ~ 50/60Hz
single phase with a fuse rating of 3A.
9. Status indicator, control & communication
cable access is via the fitted cable gland(s)
which are suitable for Ø3- 6mm cable.
10. Status indicator and communication cable
- Unshielded 4 Core 18-24AWG Stranded,
Tinned Copper.
11. Control and communication cables should
not be placed within 50mm or on the same
metal cable tray as any 230V~ lighting or
power cables.
12. Ensure all cable glands are fully tightened.
13. The unit must be stored in a clean and dry
environment. Do not install the appliance
in areas where the following may be
present or occur;
• Excessive oil or a grease laden
atmosphere.
• Corrosive or flammable gases, liquids or
vapours.
• Ambient temperatures above 40°C or
below -5°C.
• Humidity levels above 90% or is a wet
environment.
14. The appliance is not suitable for installation
to the exterior of the dwelling.
15. This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved. Children
should be supervised to ensure that they
do not play with the appliance. Cleaning
and user maintenance shall not be made
by children without supervision.
16. Ensure that external grilles are located
away from any flue outlet, in accordance
with relevant Building Regulations.
17. The unit must not be connected to a
tumble dryer or a cooker hood.
18. Precautions must be taken to avoid the
back-flow of gases into the room from an
open flue appliance.
19. Ensure all ducting, condensate drain and
associated pipe work is free from debris
and blockages before switching on the unit.

2
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Appliance Symbols
Recommendation
Read
instruction
manual.
Risk of
electric
shock.
General
hazard
safety alert.
Disconnect the
mains supply
before removing
this cover.
Wait until all machine
components have
completely stopped
before touching them.
1. A short piece of flexible ducting, approx
300mm long is used to connect the unit to
the ducting system.
2. Any flexible ducting used must be pulled
taut.
3. A minimum distance of 300mm between
the unit and any sharp bends in duct work.
4. Ducting should be insulated where it
passes through unheated areas and voids
with the equivalent of at least 25 mm of
a material having a thermal conductivity
of ≤0.04 W/(m.K) to reduce the possibility
of condensation forming. Where a duct
extends externally above roof level the
section above the roof should be insulated
or a condensate trap should be fitted just
below roof level.
5. Ducts within the building heated envelope
between the external terminals and
the unit’s From Atmosphere and To
Atmosphere ports should be insulated and
wrapped additionally with a vapour barrier
outside the insulation.
6. Where ducts pass through fire barriers,
they must be appropriately fire stopped
in accordance with the requirements of
Building Regulations.
7. A ducting condensate drain to be fitted on
vertical To Atmosphere duct work.
8. Ducting must be installed in such a way
that resistance to airflow is minimised.
9. DuctingconnectedtotheFromAtmosphere
and To Atmosphere ports, must be to/
from the external air outside the building
envelope.
10. Duct joints to the unit’s duct ports must
be fixed using a method that ensures a
long term seal is achieved. If using a short
piece of flexible ducting secure using a
hose clamp, do not over tighten.
11. A minimum distance of 2m exists between
the external supply and exhaust terminals.
Disconnect the
mains supply before
removing this cover.
Before obtaining access to terminals
or removing this cover, all supply
circuits must be disconnected.
&

3energiSava®325
SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING
THIS UNIT, CALL US ON: 0345 27 27 810
Contents
Safety
Important Information 1
Appliance Symbols 2
Recommendation 2
Product Information
Packaging Contents 4
Dimensions 4
Installation
Mounting Instructions 5
Condensate Drain 6
Ducting Connections 6
Wiring Connection Access 6
Product Overview
Controls & Features 7
Filter Covers 7
Status Indicator 7
Auto Setback Speed 7
Continuous Speed 7
Boost Speed with Overrun Timer 7
Status Indicator Boost Alert 8
Summer Bypass 8
Summer Kick Up Mode 8
Auto Setback Speed 8
Automatic Frost Protection 8
Integrated Humidity Sensor 8
Wiring Diagrams
Supply 9
Status Indicator 9
Switching & Controls 9-10
Commissioning
Controls 11
Control Parameters 12
Continuous Supply & Extract Speeds 12
Boost Supply & Extract Speeds 12
Boost Overrun 12
Humidity Sensor 12
Controller Reset 13
Hardware Reset 13
Maintenance
Routine Maintenance 14
Front Cover Removal 14
Cleaning Interior 14
Cleaning Exterior 14
Condensate Tray 14
Filter Replacement 15
How to Change Filters 15
Warranty
Terms of Warranty 16

4
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Product Information
The energiSava®325 is a whole house heat recovery unit which works by continuously
extracting stale, moisture-laden air from the “Wet Rooms” of an apartment or house - the
kitchen, bathroom and en-suite rooms - and ducts this to a central unit. This extracted air
passes through a high efficiency counter-flow heat exchanger before being ducted to the
outside. Fresh air is drawn into the unit from outside, which is warmed by the heat exchange
cell and delivered into the living, dining and bedroom areas.
Packaging Contents
Inspect the unit when taking delivery. Check
the unit for damage and that all accessories
have been supplied. Package supplied with;
• energiSava®325 unit x 1
• Mounting Bracket x 2
• Safety Bracket x 1
• 15mm Condensate Drain Olive & Nut x 1
• M6 x 10mm Pan head screws x 4
• M6 washers x 4
• Transport Bungs x 4
(Supplied packed in Duct Ports)
• Product Manual x 1
• ErP Documentation
Any shortages or damage must be
immediately reported to the supplier.
Dimensions
490
715
426

Installation Instructions
5
0345 27 27 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
energiSava®325
Read and observe the guidance & safety notices listed in the Safety section
Do not remove the port covers until connecting ducting. Port covers are fitted to prevent debris falling
into the unit and causing blockages and damage:
• The energiSava®325 is designed to be
mounted on a wall or similar. The mounting
surface must be sufficiently strong to
support the unit.
• Consider the positioning of electrical services
and the condensate drain when siting the unit.
• Ensure there is sufficient access around the
energiSava®325 for future maintenance.
• Do not ‘box-in’ the unit making access to the
unit difficult for maintenance and repair.
The unit MUST be mounted plumb and
level front to back and side to side.
1. Mark a horizontal line on the wall using a
spirit level. This line will be approximately
95mm below the location of the top face of
the unit when fitted (excluding duct ports).
2. Use one of the Mounting Brackets as a
template to mark the 3 fixing hole centres.
3. Drill holes for fixings, always use a fixing
suited to the wall type.
4. Fix one mounting bracket to the wall ensuring
the interlocking side is at the top, as shown.
5. Fix the remaining mounting bracket to
the unit using the M6 screws and washers
provided, ensuring the interlock side is at the
bottom. Do not overtighten.
6. Mount the unit by locating the two mounting
brackets together. Ensure a positive location
is made between the two mounting brackets.
7. The safety bracket MUST be fitted. Fix the
lower safety bracket as shown using the
remaining M6 screw, washer and suitable wall
fixing. Packing to be used as required behind
the safety bracket to ensure unit is level.
Safety
bracket
Hook
onto wall
bracket

Installation Instructions
6
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Condensate Drain
The unit’s condensation drain pipe must be
fitted and connected to the dwelling’s foul water
drainage system in accordance with the relevant
building regulations.
The Condensate Drain Pipe:
• Is attached via a 15mm compression fitting
(drain pipe shown un-insulated for clarity), on
the base of the unit.
• Must incorporate a suitable trap, which must
act as an air lock.
• Should be installed to have a minimum 5° fall
from the unit.
• Must be adequately secured and be insulated
with the equivalent of at least 25mm of
insulating material with a thermal conductivity
of 0.04 W/(mK) if any part of the pipe passes
though an unheated void.
• EnviroVent recommend the use of diaphragm
type waste valve in place of a conventional
‘wet’ trap which could dry out.
Ducting Connections
Read and observe the Safety section
The energiSava®325 unit has a label with the
icons indicating which port is which.
It is very important that ducting is connected
to the correct ports in line with the icons below.
EXTRACT FROM DWELLING
This duct port is connected to
the ducting that carries waste air
from the ‘Wet Rooms’ to the unit.
TO ATMOSPHERE
This duct port is connected to the
ducting that carries the waste air
to outdoors from the unit.
SUPPLY TO DWELLING
This duct port is connected to the
ducting that carries the fresh warmed
air to the habitable rooms from the unit.
FROM ATMOSPHERE
This duct port is connected to the
ducting that carries fresh outdoor
air to the unit.
Wiring Connections Access
All wiring must conform to current I.E.E.
Wiring Regulations and all applicable national
standards and Building Regulations.
Read and observe the Safety section.
The electronics compartment is mounted on top
of the unit. The compartment has two removable
lids, front & rear. The front lid must always be
removed before the rear lid; both lids are fixed by
four screws. All wiring must be routed into the
electronics compartment via the knock-outs and
using cable glands or similar.
Non-return valve
• To convert to 22mm waste pipe, use a ¾” to ½”
bush and straight / elbow compression fitting.
a. Drain - 3/4x1/2-Bush
b. Drain - 22x3/4-FEM-STR
c. Drain - 22x3/4-FEM-ELB
a
c
b

7
0345 27 27 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
energiSava®325
Product Overview
Controls & Features
The following describes the controls and features of the energiSava®325. Ensure the supplied
control is adequately labelled, indicating function clearly.
The unit can be controlled by various volt free
switches and sensors. Ensure all controls are
adequately labelled, indicating their function clearly.
Filter Covers
The filters are located behind removable covers
on the front of the unit.
Continuous Speed
Continuous speed is the normal continuous
extract and supply air flow running speed of the
units.
Auto Setback Speed
Setback speed is used to reduce ventilation rates.
Setback speed is automatically set at the mid
point between minimum possible continuous
speed and the selected continuous speed. The
setback speed can be enabled by connection of
a volt free one-way switch.
Boost Speed with Overrun Timer
Boost speed increases the extract and supply
air flow. Boost speed is configured with step-
less independent fan controls and includes an
overrun timer variable between 0 and 60 minutes.
The boost speed can be triggered by any device
which provides a volt free one-way switch, such
as a PIR, thermostat, humidistat or a standard
one-way switch.
If the unit is left in boost (latching switch) for
longer than 2 hours the overrun timer is disabled
meaning the unit will return to continuous speed
as soon as the switch holding the unit in boost
is released.
Status Indicator (included as standard)
The status indicator is a low voltage hard wired
remote LED ventilation information panel, to fit a
standard UK patress or recessed backbox. The
indicator has six LEDs which display:
• Normal
Solid Light -
Unit is running at continuous speed.
Flashing light -
Unit is running at setback speed.
• Frost
Unit is in automatic frost protection mode.
• Filter
Filters require change.
• Boost
Solid light - Unit is running at boost speed.
Flashing light boost alert is active.
• Summer
Unit is in summer bypass.
• Fault
Unit has a fault - Contact the installer.

8
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Product Overview
Status Indicator Boost Alert
Boost alert is a timer designed to prevent the unit
being inadvertently left in boost for long periods
of time. Once the unit is placed in boost the timer
is started and after 2 hours boost alert will be
activated. This is indicated by the boost LED on
the status indicator panel flashing.
Once boost alert has been activated the overrun
timer is disabled meaning the unit will return to
continuous speed as soon as the switch holding
the unit in boost is released.
Summer Bypass
Summer bypass is designed to operate during
hot periods where fresh air can be vented straight
into the property without being preheated by the
extracted stale air. Summer bypass operation is
automatically controlled.
The summer bypass mechanism diverts the
stale air being extracted from the dwelling
around the heat cell so that its heat energy is
not transferred to the fresh air being supplied to
the property.
Summer Kick Up Mode
An optional summer kick up mode facility is
available that allows both the supply and extract
fans to run at full speed whenever the summer
bypass is activated. By default summer kick
up mode is disabled by a link wire, see wiring
diagrams. Removal of the link wire will enable
summer kick up mode.
When summer kick up mode is trigged by
summer bypass, the increased fan speed can be
prevented either manually or automatically.
Manual - This is by means of a volt-free switch
wired directly into the controller PCB.
Automatic - This is by means of a dedicated
wall mounted room thermostat. Summer kick
up mode will only operate when the temperature
has exceeded the thermostat setting.
Should the room temperature fall below the
thermostat setting, then summer kick up mode
will not operate.
Automatic Frost Protection
During very cold weather, automatic frost
protection will detect temperatures that could
form ice inside the unit. It will reduce the supply
ventilation rate to prevent ice build up within the
heat cell. Automatic frost protection reduces the
flow rate of cold air, thus allowing the warmer
stale air to raise the temperature within the heat
cell to such a level that prevents the formation
of ice.
As internal temperatures rise, the automatic frost
protection will increase the supply ventilation
flow rate back to the commissioned settings.
Integrated Humidity Sensor
Units are fitted with an integrated humidity
sensor. This continuously monitors the relative
humidity (RH) of the extracted air and triggers
boost speed when the relative humidity rises
over the set threshold.
The humidity sensor’s trigger point is variable
from 55% RH to 85% RH and is configured using
step-less independent potentiometer.
Enthalpy Humidity-Recovery
Units with the E suffix use an enthalpy heat
recovery core that recovers some of the humidity
as well as heat.

9energiSava®325
SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING
THIS UNIT, CALL US ON: 0345 27 27 810
Wiring Diagrams
Mains Supply Switching and Controls
Status Indicator
Mains cable must be separate from the
communication cables.
See Important Information.
Supply wiring diagram 230V~
Connection at unit
L
N
12V
A
B
0V
12V
A
B
0V
L
N
FuseDouble Pole Isolator Summer kick up link wire must be
removed to enable summer kick up
Summer kick up link wire
Connection at indicator

10
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Wiring Diagrams
Switching and Controls
Volt-free control of Summer Kick Up using
one way latching switch.
Volt-free Boost switching of MVHR.
There is maximum of 10 single pole switches
or humidistats that can be used.
To Boost using switch live, a relay is required.
(SWHT-BOXRELAY)
Volt-free setback switch or
normally open relay contacts
112323 Volt-free
sensor
Volt-free Setback switching of MVHR controller
PCB using single-pole latching switch and / or
volt-free normally open relay contacts.
To avoid the unit being inadvertently left in
setback mode, it is recommended that only
one latching switch is fitted.
Latching Summer
Kick Up switch
(SWHT-BOOST-L)
Momentary Boost
switch
(SWHT-BOOST-M)

11 energiSava®325
SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING
THIS UNIT, CALL US ON: 0345 27 27 810
Commissioning
Controls
The fan speeds of the energiSava®325 will require adjustment to ensure the flow rates
achieved provide adequate ventilation. The energiSava®325 has 2 standard fan speed settings
continuous speed and boost speed.
The continuous speed and boost speed are programmed by placing the controller into program
mode via the program/run switch and changing the position of the rotary potentiometers.
When applying power for the first time, the unit can take up to four minutes to start operating.
Prior to the first commission set continuous speed potentiometers to minimum and boost
speed potentiometers to maximum or reset the controller.
Program
Switch Humidity
Timer
Potentiometers
Extract Supply Run
Humidity
Sensor
Extract Supply
Boost Continuous Boost
Overrun
Timer

12
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Commissioning
Control Parameters
• The boost speed cannot be set lower than
the continuous speed.
• The continuous speed cannot be set higher
than the boost speed.
• All switching inputs are disabled when the
program/run switch is in continuous or
boost positions.
• Speed control potentiometers are disabled
when the program/run switch is in centre
run position.
Boost Supply & Extract Speeds
• Move program/run switch to boost position.
• Rotate supply fan boost speed adjustment
potentiometer to achieve required supply
boost air flow.
• Rotate extract fan boost speed adjustment
potentiometer to achieve required extract
boost air flow.
• Return program/run switch to centre
position to exit commissioning.
For the commissioning settings to be
stored the unit needs to be powered up.
Continuous Supply & Extract Speeds
• Move program/run switch to continuous
position.
• Rotate supply fan continuous speed
adjustment potentiometer to achieve
required supply continuous air flow.
• Rotate extract fan continuous speed
adjustment potentiometer to achieve
required extract continuous air flow.
• Return program/run switch to centre
position to exit commissioning.
Boost Overrun
Boost overrun timer is variable between 0 and
60 minutes. Rotate potentiometer to change
overrun time. This can be done at any time.
Humidity Sensor
The humidity sensor’s trigger point is variable
from 55% RH to 85% RH. Rotate potentiometer
to change trigger point. The humidity sensor
adjustment can be done at any time without
the need to move the program/run header
link.
1
2
3
45
6
7
8

13 energiSava®325
SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING
THIS UNIT, CALL US ON: 0345 27 27 810
Commissioning
Controller Reset
Following a controller reset the ventilation
system will need to be fully commissioned.
The procedure to reset the energiSava®325
controller is a simple three step operation.
The unit will need to be powered up during
the reset procedure.
1. Rotate the supply & extract continuous
Speed potentiometers fully anti-clockwise.
2. Rotate supply and extract boost speed
potentiometers fully clockwise move the
run/program switch from the run position
to the continuous position, from the
continuous position to the boost position
and back to the run position.
To ensure that the reset switch
movements are registered by the
controller wait 2 seconds between each
switch movement. Controller reset is
now complete.
Hardware Reset
Certain conditions (repeated supply
interruptions etc.) can activate the automatic
motor protection mode. Whereby the fan
motors are prevented from operating.
This requires a hardware reset to return the
unit to normal operating mode, to achieve
this power to the unit should be switched
off for 5 minutes, restoring the power after
this time will reset the hardware of both the
motor and PCB. Commissioning settings are
not affected during a hardware reset.

14
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Front Cover Removal
1. ISOLATE the unit from mains power
supply and allow sufficient time for all
moving parts to stop.
2. Loosen the two corner screws located on
the bottom front of the unit.
3. Completely remove the centre screw.
4. Completely remove the front cover by
pulling it away from the unit at the bottom
and lifting.
Cover replacement is the reverse of the
above steps. Ensure it is securely located
at the top before tightening screws.
Cleaning Interior
For best results:
1. Slide out filter frames fitted either side of
heat exchanger.
2. Carefully remove any dust from face of
heat exchanger, interior of the unit and
the bypass (if fitted) using a vacuum
cleaner.
Do not use water or any other fluids
Cleaning Exterior
For best results use a clean damp cloth. Do
not use abrasive cleaners, solvents or any
other fluids.
Condensate Tray
If the condensate tray is split a replacement
must be ordered and fitted.
Maintenance
Routine Maintenance
All ventilation units require periodic maintenance. Routine maintenance, apart from filter
changes, must only be carried out by a suitably qualified and competent person.
WARNING: The unit uses a 230V~ supply and contains rotating mechanical parts. ISOLATE
the unit from mains power supply and allow sufficient time for all moving parts to stop
before undergoing any servicing or maintenance.
100mm MAX
1
2

15 energiSava®325
SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING
THIS UNIT, CALL US ON: 0345 27 27 810
Maintenance
Filter Replacement
Filters should be replaced at least annually, or more regularly dependent on environmental
conditions. The status indicator will indicate filter change required in line with the filter change
interval setting. Replacement filters are available from EnviroVent.
energiSava®325 filters are available in two grades G3 and G4. Filter media should be replaced
like for like. Filter part numbers in table below.
G3 Filters
Both faces white
G4 Filters
One face white, one face blue
G3 Filter Set
2 framed filters FILTER-G3-ES325
G4 Filter Set
2 framed filters FILTER-G4-ES325
How to Change Filters
1. Remove front cover or filter covers.
2. Slide out filters.
3. The energiSava®325 filters uses unequal
filters. Make a note of which side of the
unit the filter with the shorter filter media
is. The positions of filters is marked on
the unit.
4. Replace filters by carefully sliding in the
replacement filters. Ensure that filters are
replaced in the same positions as they
were removed. The positions of filters is
marked on the units.
5. Replace the front cover or filter covers.
Shorter Media Filter
Status Indicator Filter Notification Reset
Ensure the unit is powered up. To clear the
status indicator filter notification press &
hold the reset switch with a ball point pen
or similar object for 10 seconds. The switch
is located behind the small hole in the
front of the status indicator. All lights will
momentarily be illuminated indicating a
successful reset.

16
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Warranty
We appreciate you choosing this quality EnviroVent product. We are confident that you will be
delighted with the performance of the system and the resulting improvement in air quality in
your home after it has been installed.
This unit is covered by a 2-year warranty, subject to the replacement of filters every 12
months, or more frequently as required, dependant on the environmental conditions. You
should not dismantle or remove any parts of the product other than those instructed in
this guide. Tampering with the unit will void the warranty. The valves should be checked
periodically to ensure there is air flowing through the system.
EnviroVent Supply & Installation
If your product has been supplied and installed by EnviroVent Ltd it is covered with a two-
year parts and labour warranty. If you detect a fault, please contact us on 01423 810810. You
will be given guidance over the phone, or an arrangement may be made for a member of our
team to visit (call-out charges may apply if a fault cannot be identified).
Supply Only
If your product has been supplied by EnviroVent and installed by a third party it is covered
by a two-year parts only warranty. If you detect a fault and the product has been installed
in accordance to the fitting/wiring instructions, relevant guidance documents and by a
competent and qualified person (proof may be required), please return the product to the
place of purchase for a replacement.
Warranty Conditions & Exclusions
Please note that a receipt will be required as proof of purchase. Products bought from an
unapproved source, including but not limited to auction websites, are not covered by the
warranty.
• The system must be correctly installed and operated according to the instructions
contained in the user guide supplied.
• The warranty will be rendered invalid if the system has been serviced, maintained,
repaired, taken apart or tampered with by any person not authorized, which in any way
contradicts the instruction guide set out by EnviroVent.
• The warranty does not cover accidental damage, misuse or abuse.
• The warranty is in addition to your statutory or legal rights.
Your unit serial number
For warranty conditions and exclusions, visit www.envirovent.com/warranty

17 energiSava®325
SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING
THIS UNIT, CALL US ON: 0345 27 27 810
Serviced By Company Date Notes
Service Record

18
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Weee Directive
To all residents of the European Union;
Important environmental information about
this product. This symbol on this unit or
the package, indicates that disposal of
this unit after its lifecycle could harm the
environment.
Do not dispose the unit as unsorted
municipal waste; it should be disposed by a
specialized company for recycling. This unit
should be returned to your distributor or to
a local recycling service. Respect the local
environmental rules. If any doubt contact your
local authorities about waste disposal rules.

We want to hear from you
Your feedback is important to us as we strive to improve our
products, services, and overall customer experience. Please email
us to help us serve you better: [e-mail]
AFTER INSTALLING THIS UNIT PLEASE PASS ONTO END USER
DO NOT THROW AWAY
Please read carefully to ensure
simple installation and a long
trouble free life for the user.
Delivering innovative and sustainable
ventilation solutions worldwide
EnviroVent Ltd
EnviroVent House
Hornbeam Business Park
Harrogate
HG2 8PA
T / 01423 810 810
F / 01423 301 022
E / [email protected]
W / envirovent.com
E&OE | MKT ENV341-V3-18.12.20
Due to our policy of continuous innovation
and improvement EnviroVent reserves
the right to alter products specification
and appearance without notice.