Epson Stylus Scan 2000 User manual

English
Setup Guide
All in One Product
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information
contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any
use of this information as applied to other printers.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this
product orthird parties for damages, losses,costs, orexpenses incurred bythepurchaseror thirdparties
as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or
alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON
CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the
useofanyoptionsoranyconsumableproductsotherthanthosedesignatedasOriginalEPSONProducts
or EPSON Approved Products by SEIKO EPSON CORPORATION.
SEIKO EPSON CORPORATION shall not be held liable for any damage resulting from
electromagnetic interference that occurs from the use of any interface cables other than EPSON
Approved Products by SEIKO EPSON CORPORATION.
EPSON is a registered trademark and EPSON ESC/P and EPSON Stylus are trademarks of SEIKO
EPSON CORPORATION.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice: Other product names used herein are for identification purposes only and may be
trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 1999 by SEIKO EPSON CORPORATION, Nagano, Japan.

Declaration of Conformity
According to ISO/IEC Guide 22 and EN 45014
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi,
Nagano-ken 392-8502 Japan
Representative: EPSON EUROPE B.V.
Address: Prof. J. H. Bavincklaan 5
1183 AT Amstelveen
The Netherlands
Declares that the Product:
Product Name: Multi Function Printer
Model: C120A
Conforms to the following Directive(s) and Norm(s):
Directive 89/336/EEC: EN 55022 Class B
EN 61000-3-2
EN 61000-3-3
EN 50082-1
IEC 801-2
IEC 801-3
IEC 801-4
Directive 73/23/EEC: EN 60950
June 1999
H. Horiuchi
President of EPSON EUROPE B.V.

3
English
Contents
Where to Find Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Quick Start Manual (this manual) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Online Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
A Few Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ENERGY STAR Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Symbols Used in the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
For PCs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
For Macintosh computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting Up Your Stylus Scan 2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attaching the Paper Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Plugging in the EPSON Stylus Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the Stylus Scan to Your Computer . . . . . . . . . . . . . . . . . . . . 8
Installing the Drivers and Other Software in Your PC . . . . . . . . . . . . . . 9
Installing the Ink Cartridges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Checking the Stylus Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Loading Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Printing the Nozzle Check Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning the Print Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
After Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing the Connection Port (for Windows 98) . . . . . . . . . . . . . . . . . . 30
Printing Your First Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
For Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
For Macintosh. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ink Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using the Online Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installing the Adobe Acrobat Reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Accessing the Online Manuals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

4Where to Find Information
■Where to Find Information
❚Setup Guide (this manual)
Containsinformation about howtosetupyourStylusScan 2000, install theStylus Scan
2000 software and access your online documentation. It also provides instructions for
daily operation. Keep this manual near your printer.
❚Online Documentation
The CD-ROMs supplied with the Stylus Scan 2000 include a set of online documenta-
tion in PDF format containing further information and reference tips.
❚Online Help
Provides you with detailed information and instructions on the Stylus Scan 2000
software for Windows that controls your printer. Online help will be automatically
installed when you install the Stylus Scan 2000 software.
■Important Safety Instructions
Read all of these instructions before using your EPSON Stylus Scan. Also be sure to
follow all warnings and instructions marked on the Stylus Scan.
■Unplug the Stylus Scan beforecleaning. Clean with a damp clothonly. Do not spill
liquid on the Stylus Scan.
■DonotplacetheStylusScanon anunstable surface, orneararadiatororheat source.
■Do not block or cover the openings in the Stylus Scan’s cabinet.
■Do not insert objects through the slots. Take care not to spill liquid on the Stylus
Scan.
■Use only the type of power source indicated on the Stylus Scan’s label.
■Connect all equipment to properly grounded power outlets. Avoid using outlets on
the samecircuit as air controlsystems, or other devicesthat consumelargeamounts
of electricity and regularly switch on and off.
■Avoid electrical outlets controlled by wall switches or automatic timers.
■Keep the entire computer system away from potential sources of electromagnetic
interference, such as loudspeakers and the base units of cordless telephones.
■Do not use a damaged or frayed power cord.
■If you usean extension cord withthe Stylus Scan,make sure the totalampere rating
of the devices plugged into the extension cord does not exceed the cord’s ampere
rating. Also, make sure the total ampere rating of all devices plugged into the wall
outlet does not exceed the wall outlet’s ampere rating.
■Do not attempt to service the EPSON Stylus Scan yourself.

5
Important Safety Instructions
English
■Unplug the Stylus Scan and refer servicing to qualified service personnel under the
following conditions:
The power cord or plug is damaged; liquid has entered the Stylus Scan; the Stylus
Scan has been dropped or the cabinet damaged; the Stylus Scan does not operate
normally or exhibits a distinct change in performance.
■To provide adequate short-circuit protection and over-current protection for this
Stylus Scan, the buildinginstallation must be protected by a16 Amp circuit breaker
Thisdevicecontainsbatteriesandshouldnotthereforebedisposedofwith
normal domestic waste. Please dispose of the device in accordance with
local statutory regulation.
❚A Few Precautions
■When using the Stylus Scan
■Do not put your hand inside the Stylus Scan or touch the ink cartridges during
operation.
■Donotmovetheprintheadbyhand.DoingsomaydamagetheEPSONStylusScan.
■Always use the P power button to turn off the Stylus Scan. After pressing this
button, the P power light flashes briefly then goes off. Do not unplug the Stylus
Scan or turn off the power to the outlet until the P power light stops flashing.
■Before transporting the Stylus Scan, make sure the print head is in the home (far
right) position and the ink cartridges are in place.
■When handling the ink cartridges
■Keep ink cartridges out of the reach of children. Do not allow children to drink the
ink or otherwise handle the cartridges.
■If ink gets on your skin, wash it off with soap and water. If ink gets into your eyes,
flush eyes immediately with water.
■Do not shake the ink cartridges. Cartridges may leak if shaken.
■Install the ink cartridge immediately after you remove it from its package. Leaving
thecartridgeunpackedforalongtime beforeusemayresultinreducedprintquality.
■Once you install an ink cartridge, do not open the clamp or remove the cartridge
except to replace it with a new one. Otherwise the cartridge may become unusable.
■Do not use an ink cartridge beyond the date printed on the cartridge carton. For best
results, use up the ink cartridges within six months of installing them.
■Do not dismantlethe ink cartridges or try to refill them. Doingso may damage the
print head.

6ENERGY STAR Compliance
■When choosing a place for the Stylus Scan
■PlacetheEPSONStylusScanonaflat,stablesurfacethatextendsbeyondtheStylus
Scan base in all directions. The Stylus Scan will not operate properly if it is tilted
or at an angle.
■Avoid places subject to rapid changes in temperature and humidity. Also, keep the
Stylus Scan away from direct sunlight, strong light, and heat sources.
■Avoid places subject to shocks and vibrations.
■Leave enough room around the Stylus Scan to allow for sufficient ventilation.
■Place the Stylus Scan near a wall outlet where the plug can be easily unplugged.
■ENERGY STAR Compliance
As an ENERGY STAR Partner, EPSON has determined that this
product meets the ENERGY STAR guidelines for energy effi-
ciency.
TheInternationalENERGY STAR Office Equipment Program is
a voluntary partnership with the computer and office equipment
industry to promote the introduction of energy-efficient personal computers, monitors,
printers, fax machines, and copiers in an effort to reduce air pollution caused by power
generation.
■Symbols Used in the Manual
w
Warnings
must be followed carefully to avoid bodily injury.
c
Cautions
must be observed to avoid damage to your equipment.
Note:
contain important information and useful tips on the operation of your Stylus Scan.
■System Requirements
❚For PCs
To use your EPSON Stylus Scan, you need Microsoft®Windows®95, or Windows®
98; and CD-ROM drive and a shielded, twisted-pair parallel cable. If you want to
connect your printer toa USB port, you needa Windows 98 pre-installedPC equipped
with a USB port; and a shielded USB cable.

7
System Requirements
English
Your computer should also meet the following system requirements.
Your computer dealer can help you update your system if it does not meet these
requirements.
❚For Macintosh computers
You can use this printer with the following Apple®Macintosh®computers. You also
need a shielded USB cable.
Applicable computer models:
iMac Series (for USB)
Power Macintosh G3 (for USB)
Your Macintosh must also meet the following system requirements.
Note:
Macintosh can be connected to the Stylus Scan by using a USB cable only.
Note:
❏The amount of available memory varies according to the number and kind of
applicationsthatareopen.Toseehowmuchmemoryisavailable,chooseAbout
This Computer
from the Apple menu and refer to the memory size (listed
in kilobytes) under Largest Unused Block (1,024K=1 MB).
❏The memory requirements above are for printing on Letter size paper. These
requirements may vary depending on the size of the paper, the type of applica-
tion you are using, and the complexity of the document you want to print.
In addition to these system and memory requirements, you also need 10 MB of free
hard disk space to install your printer software. To print, you need extra hard disk space
amounting to about double the size of the file you want to print.
Minimum System Requirements Recommended System
i486/25 MHz for Windows 95
i486/66 MHz for Windows 98 Pentium or higher processor
32 MB RAM 32 MB RAM or more for
Windows 95 and 98
50 MB harddisk space for Windows 95,
and 98 50MBormorefreediskspace for Windows 95, and 98
VGA size, 16 bit color SVGA or better 24 bit color
Minimum System Requirements Recommended System
System 8.1 + iMac update System 8.5.1 or later
7 MB of available memory
12MBof availablememory when
backgroundprintingisturnedon.
14MBormoreofavailablememory
23 MB of available memory when
background printing is turned on.

8Setting Up Your Stylus Scan 2000
■Setting Up Your Stylus Scan 2000
❚Attaching the Paper Support
The EPSON Stylus Scan comes with two paper supports.
■Paper support (gray)
Fit the paper support into the slots at the rear of the EPSON Stylus Scan.
■Document support (transparent)
Carefully fit the document support into the holes at the rear of the EPSON Stylus
Scan.
❚Plugging in the EPSON Stylus Scan
1. Make sure that the Stylus Scan is turned off. It is off when the P power button
protrudes slightly from the surface of the control panel.
2. Check the label on the back of the Stylus Scan to make sure the voltage required
by the Stylus Scan matches thatof the electrical outlet you plugit into. Also, make
sure that you have the correct power cable for your power source.
c
Caution:
ItisnotpossibletochangetheStylusScan’svoltage.Iftheratedvoltage
and your outlet voltage do not match, contact your dealer for assis-
tance. Do not plug in the power cord.
3. If the power cord is not attached to the Stylus Scan, connect it to the AC inlet at
the back of the Stylus Scan.
4. Plug the power cord into a properly grounded electrical outlet.
❚Connecting the Stylus Scan to Your Computer
Your Stylus Scan has two ports through which it can be connected to a computer; a
parallel port and a USB port. Use the port appropriate for your computer.
Note:Note:
❏If your computer has both a parallel and USB port, be sure to followthe correct
steps for connecting to the port you choose.
paper support
document support

9
Setting Up Your Stylus Scan 2000
English
❏Do not use the Stylus Scan’s parallel port and USB port simultaneously.
Connect the Stylus Scan to one computer at a time.
■Using the parallel port (for Windows 95 or 98)
To connect the Stylus Scan to your PC using the parallel port, you need a shielded,
twisted-pair parallel cable. Follow these steps.
1. Make sure both the Stylus Scan and computer are turned off.
2. Plug the cable connector securely into the parallel interface connector at the rear
of the Stylus Scan. Then squeeze the wire clips together until they lock in place
on both sides.
3. Plug the other end of the cable into the computer’s parallel interface. If there is a
ground wire at the computer end of the cable, connect it to the ground connector
at the back of the computer.
You are now ready to install the Stylus Scan drivers. For installation instructions, see
“For Windows 95 or 98 with a parallel connection” on page 10.
■Using the USB port (for Windows 98 or Macintosh)
To connect the Stylus Scan to your computer using the USB port, you must first install
the Stylus Scan drivers.
See “For Windows 98 with a USB connection” on page 13 to install the drivers and
connect the Stylus Scan to your Windows 98 computer using the USB port.
To install the software and connect the Stylus Scan to your Macintosh, see “Installing
the Software in Your Macintosh” on page 19.
❚Installing the Drivers and Other Software in Your PC
Your Stylus Scancomes with the EPSON Stylus Scan 2000 Software for Windows
CD-ROM which includes software for your Stylus Scan.
To print and scan with your Stylus Scan, you need to install the following software
included on the CD-ROM.
■EPSON SMART PANEL
Provides easy access to the Stylus Scan’s scanning, printing, and copying features.
■EPSON Stylus Scan 2000 Drivers
Printer Driver
Allows you to use the Stylus Scan’s printer function.

10 Setting Up Your Stylus Scan 2000
EPSON Stylus Scan SF TWAIN
Allows you to use the Stylus Scan’s scanner function.
The included CD-ROM also contains the following software.
■Acrobat Reader
This software enables you to read the manuals for EPSON SMART PANEL and
WinFAX, or any other files that are in the Portable Document Format (PDF).
■WinFax BASIC EDITION
Includes applications that support the Stylus Scan’s fax features and other special
operations.
■For Windows 95 or 98 with a parallel connection
After connecting the Stylus Scan to your computer as described in “Using the parallel
port (for Windows 95 or 98)” on page 9, follow the steps below to install the drivers
and other software.
Note for users with a parallel connection:
Before installing the software on your computer, make sure there is no Stylus Scan
driver already installed on your computer. If there is, see “Uninstalling the parallel
driver” on page 30 to uninstall the software before following the steps below.
1. Turn on the computer and start Windows.
Note:
If you turn on the EPSON Stylus Scan before turning on your PC, the computer may
detect the Stylus Scan and display the New Hardware Found dialog box, or a similar
wizard, following start-up. If this occurs, click the Cancel button to close the dialog
box, and continue with installation as described below.
2. Insert the EPSON Stylus Scan 2000 Software for Windows CD-ROM in the
CD-ROM drive. Then the Select Language dialog box appears.
3. Select the language you want and click OK.

11
Setting Up Your Stylus Scan 2000
English
4. Click the Add Software button.
5. TheEPSONSoftwareSetup dialog box appears. Make sure there is a check mark
next to EPSON SMART PANEL and EPSON Stylus Scan 2000 Drivers. Clear the
check marks next to the names of any other software that you do not want to install.
6. Click OK.
7. Follow the on-screen instructions to install the EPSON SMART PANEL.
8. When the EPSON SMART PANEL installation is complete, the EPSON Stylus
Scan Setup dialog box appears. Click Next.

12 Setting Up Your Stylus Scan 2000
9. In Windows 98, the following dialog box appears. Select LPT (PrinterPort), then
click Next to begin installation. (If this dialog box does not appear, go to the next
step.)
10. When installation is complete, click OK to start the EPSON Screen Calibration
utility.
Note:
Be sure to calibrate your screen and Stylus Scan to ensure that the colors of
reproduced images closely match the originals.

13
Setting Up Your Stylus Scan 2000
English
11. In the following window, move the slider to the right or left until the two shades
of gray horizontal stripes match.
Note:
The gray stripes will not perfectly blendtogether; however, try tomake the two
tones match as closely as possible.
12. Click OK to register the calibration setting.
13. When the EPSON Stylus Scan Drivers installation is complete, installation for
other applications begins automatically. Follow the on-screen instructions.
14. After all applications have been installed, a message appears asking you to restart
your computer. Click OK.
15. Restart the computer, then turn on the Stylus Scan by pressing its P power button.
Note:
Do not change the printer name (leave it as Stylus Scan 2000), otherwise your Stylus
Scan does not work correctly.
■For Windows 98 with a USB connection
Before connecting the Stylus Scan to your Windows 98 computer using the USB port,
you must first install the Stylus Scan software. This section guides you through the
software installation and also includes instructions on connecting to your computer
using the USB port. Follow the steps below.
Note:
The USB connection cannot be used with Windows 95.
1. Turn on the computer and start Windows 98.
d

14 Setting Up Your Stylus Scan 2000
Note:
If you turn on the EPSON Stylus Scan before turning on your computer, the computer
may detect the Stylus Scan and display the New Hardware Found dialog box, or a
similar wizard, following start-up. If this occurs, click the Cancel button to close the
dialog box and remove the USB cable. Then continue with installation as described
below.
2. Insert the EPSON Stylus Scan 2000 Software for Windows CD-ROM in the
CD-ROM drive. The Select Language dialog box appears.
3. Select the language you want and click OK.
4. Click the Add Software button.
5. TheEPSONSoftware Setupdialog box appears. Make sure there is acheck mark
next to EPSON SMART PANEL and EPSON Stylus Scan 2000 Drivers. Clear the
check marks next to the names of any other software that you do not want to install.
6. Click OK.

15
Setting Up Your Stylus Scan 2000
English
7. Follow the on-screen instructions to install the EPSON SMART PANEL.
8. When the EPSON SMART PANEL installation is complete, the EPSON Stylus
Scan Setup dialog box appears. Click Next.
9. The following dialog box appears. Select USB, then click Next.
10. The following message appears.
Click OK. Installation for other applications begins automatically. Follow the on-
screen instructions.

16 Setting Up Your Stylus Scan 2000
11. After the applications have been installed, the following message appears.
Click OK and restart your computer. Then turn on the Stylus Scan by pressing the
P power button.
12. Plug the appropriate end of the cable into the USB port on the back of the Stylus
Scan. (The end that fits the Stylus Scan has a different shape from the end that fits
the computer.)
Note:
To connect the Stylus Scan to a USB port, you need a standard shielded USB
cable.
13. Connect the other end of the cable to the computer’s USB port.
Note:
If you have more than one USB hub connected to your computer, connect the
StylusScan to the hubthat isconnecteddirectlytoyourcomputer. IftheEPSON
Stylus Scan does not work properly when connected to the hub, connect it
directly to the computer’s USB port.
14. If the following dialog box appears, click Next. Otherwise skip to step 19.

17
Setting Up Your Stylus Scan 2000
English
15. The following dialog box appears. Click Next.
16. In the following dialog box, clear all the check boxes, then click Next.
17. In the following dialog box, click Next to install the required drivers.
Note:
If a dialog box appears asking you to specify the location of the Windows 98
CD-ROM, insert the Windows 98 CD-ROM into the CD-ROM drive and click
OK.

18 Setting Up Your Stylus Scan 2000
18. Click Finish to complete the USB Hub driver installation.
19. The following message appears.
Make sure the EPSON Stylus Scan 2000 Software for Windows CD-ROM is
still in your CD-ROM drive, and click OK.
20. The following dialog box appears.
IntheCopyfilesfrombox,typeD:\EPSON\ENGLISH(oryourpreferredlanguage).
Then click OK. If your CD-ROM drive has a drive letter other than D, substitute
the appropriate letter. The system installs the required driver.
21. To install the printer driver and scanner driver, follow the same procedure as step
19 to 20.
Note:
Depending on your computer, you should repeat the step 21 again.
22. During the driver installation, the EPSON Screen Calibration utility starts auto-
matically.

19
Setting Up Your Stylus Scan 2000
English
Note:
Be sure to calibrate your screen and Stylus Scan to ensure that the colors of
reproduced images closely match the originals.
23. In the following window, move the slider to the right or left until the two shades
of gray horizontal stripes match.
Note:
The gray stripes will not perfectly blendtogether; however, try tomake the two
tones match as closely as possible.
24. Click OK to register the calibration setting.
25. Follow the on-screen instructions to complete the installation.
Note:
Do not change the printer name (leave it as Stylus Scan 2000), otherwise your Stylus
Scan will not work correctly.
■Installing the Software in Your Macintosh
To print and scan with your Stylus Scan, you need to install the following software
included on the EPSON Stylus Scan 2000 Software for Macintosh CD-ROM
shipped with your Stylus Scan. This software must be installed before connecting the
Stylus Scan to your Macintosh.
■EPSON Stylus Scan 2000 Drivers
Printer Driver
Allows you to use the Stylus Scan’s printer function.
EPSON Stylus Scan SF TWAIN
Allows you to use the Stylus Scan’s scanner function.
The included CD-ROM also contains the following software.
■EPSON PersonalCopy
Enables you to easily create high quality color copies.
■Presto! PageManager for EPSON
Allows you to easily access the Stylus Scan’s scanning and printing features.
d

20 Setting Up Your Stylus Scan 2000
■Acrobat Reader
Thissoftwareenables youto read themanualforPresto! PageManagerforEPSON,
or any other file that is in the Portable Document Format (PDF).
Follow these steps to install your Stylus Scan software, and to connect the Stylus Scan
to your Macintosh.
c
Caution:
TurnoffallvirusprotectionprogramsbeforeyouinstallyourEPSONStylus
Scan software.
Note for iMac users:
If you are using Mac OS 8.1, you need to install the iMac Update 1.0 before installing
the Stylus Scan software. This update, along with complete update information, is
available online from the Apple Web site. If you are using Mac OS 8.5, you do not need
to install the iMac Update.
1. Turn on your Macintosh and insert the EPSON Stylus Scan 2000 Software for
Macintosh CD-ROM in the CD-ROM drive. The EPSON window appears.
2. To install EPSON PersonalCopy, Presto! PageManager for EPSON, or Acrobat
Reader, double-click the appropriate folder. Then double-click the folder of your
preferred language, and double-click the corresponding installer icon. Follow the
on-screen instructions.
3. After installation of the programs in the previous step is complete, double-click
the EPSON Stylus Scan Drivers folder.
4. Double-click the folder for your preferred language, then double-click the EPSON
Stylus Scan 2000 icon. The following dialog box appears.
5. Click Install, then follow the on-screen instructions.
6. When the following dialog box appears, click Restart.