Epson EPL N2700 User manual

EPSONEPL-N2700OptionalUnits
SEPG98007

®

Notice:
 All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
 The contents of this manual are subject to change without notice.
 All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON
would greatly appreciate being informed of them.
 The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences
thereof.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
General Notice: Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their
respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 1996 SEIKO EPSON CORPORATION. Printed in Japan.

PREFACE
This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of EPSON EPL-N2700
Optional Units. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to
the precautions on the preceding page. The chapters are organized as follows:
PCHAPTER 1. DOUBLE CASSETTE UNIT
Describes the step-by-step procedures for disassembling and assembling the
Double Cassette Unit.
CHAPTER 2. DUPLEX UNIT
Describes the step-by-step procedures for disassembling and assembling the
Duplex Unit.
CHAPTER 3. LCC UNIT
Describes the step-by-step procedures for disassembling and assembling the
LCC Unit.
CHAPTER 4. 5-BIN UNIT
Describes the step-by-step procedures for disassembling and assembling the 5-
Bin Unit.
CHAPTER 5. 10-BIN UNIT
Describes the step-by-step procedures for disassembling and assembling the
Double Cassette Unit.
CHAPTER 6. Operating Principles for Optional Units
Explains the operating principles of each optional unit.

Revision Status
Revision Issued Date Description
A Fuburary 10, 1999 Revision A

Contents
Double Cassette Unit
Installing the Double Cassette Unit ................................................................. 9
Disassembly and Assembly of the Double Cassette Unit ............................... 11
Paper Take-up Roller Removal ........................................................................... 11
Paper Empty Sensor Removal ............................................................................ 11
Paper Near Empty Sensor Removal ................................................................... 12
Paper Feed Sensor Removal .............................................................................. 12
Paper Size Sensor (Paper Size Switch) Removal ............................................... 13
Controller Board (PWB-A) Removal .................................................................... 13
Paper Take-up Solenoid Removal ...................................................................... 14
Right Door Set Sensor Removal ......................................................................... 15
Maintenance of the Double Cassette Unit ...................................................... 16
Cleaning the Paper Take-up Roller ..................................................................... 16
Cleaning the Transport Roller ............................................................................. 16
Exploded Diagrams for Double Cassette Unit ................................................ 17
Housing ............................................................................................................... 17
Paper Take-up Section ........................................................................................ 19
Paper Tray Unit ................................................................................................... 21
Duplex Unit
Installing the Duplex Unit .............................................................................. 24
Disassembly and Assembly of the Duplex Unit ............................................. 26
Duplex Unit Door Set Sensor Removal ............................................................... 26
Main Board Removal ........................................................................................... 27
Switch Back Motor Removal ............................................................................... 28
Transport Motor Removal .................................................................................... 29
Transport Roller Removal ................................................................................... 30
Maintenance of the Duplex Unit .................................................................... 31
Cleaning the Transport Roller ............................................................................. 31
Exploded Diagrams for Duplex Unit .............................................................. 32
LCC Unit
Installing the LCC Unit .................................................................................. 35
Disassembly and Assembly of the LCC Unit .................................................. 37
Separate Roller/Torque Limiter Removal ............................................................ 37
Feed Roller Removal .......................................................................................... 37
Paper Take-up Unit Removal .............................................................................. 38
Lift-up Sensor Removal ...................................................................... 39
Paper Take-up Roller (Right) Assembly Removal .............................. 40
Right Paper Take-up Clutch Removal ................................................ 42
Paper Take-up Roller (Left) Assembly Removal ................................ 43
Paper Take-up Clutch (Left) Removal ................................................ 45
Paper Take-up Roller Removal .......................................................... 45
LCC Paper Take-up Sensor (PPS0) Removal ................................... 46
Paper Empty Sensor 1 (PPS1) Removal ........................................... 46
Paper Empty Sensor 2 (PPS2) Removal ........................................... 46
Paper Stand-by Position Sensor Removal ......................................... 47
Registration Sensor Removal ............................................................. 47
Side Cover Set Sensor Removal ........................................................ 48
Registration Clutch (RCL) Removal ................................................... 49
Separate Clutch Removal .................................................................. 49
Registration Roller Removal ............................................................... 51
Separate Roller Shaft Removal .......................................................... 51
Feed Roller Shaft Removal ................................................................ 51
Drive Section Disassembly ................................................................................. 52
LCC Transport Motor Removal .......................................................... 52
LCC Set Sensor Removal .................................................................. 53
Paper Near Empty Sensor Removal .................................................. 53
LCC Lift-up Motor Removal ................................................................ 54
LCC Main Board Removal .................................................................. 55
Paper Tray Unit Disassembly .............................................................................. 56
Roller with the Torque Limiter Removal ............................................. 56
Timing Belt Removal .......................................................................... 57
Lifter Drive Shaft Removal ................................................................. 59
Maintenance of the LCC Unit ......................................................................... 60
Maintenance Items .............................................................................................. 60
Cleaning the Paper Take-up Roller ..................................................................... 60
Cleaning the Feed/Separate Roller ..................................................................... 61
Cleaning the Vertical Transport Roller / Roller (Driven) ...................................... 61
Cleaning the Roller with a Torque Limiter ........................................................... 62

Exploded Diagrams for LCC Unit ................................................................... 63
Housing ............................................................................................................... 63
Paper Take-up Section (A) .................................................................................. 65
Paper Take-up Section (B) .................................................................................. 67
Drive Section ....................................................................................................... 69
Paper Tray Unit (A) ............................................................................................. 71
Paper Tray Unit (B) ............................................................................................. 73
5-Bin Unit
Installing the 5-Bin Unit ................................................................................. 76
Disassembly and Assembly of the 5-Bin Unit ................................................ 80
Front Cover Removal .......................................................................................... 80
Rear Cover Removal ........................................................................................... 80
Jammed Paper Remove Door Removal .............................................................. 80
Shift Motor (M2) Removal ................................................................................... 81
Guide Position Sensor (PC3) Removal ............................................................... 82
Control Board (PWB-A) Removal ........................................................................ 82
Bin 4/ Bin 5 Switch Solenoid (SL2) Removal ...................................................... 83
Jammed Paper Remove Door Sensor (PC1) Removal ....................................... 84
Transport Motor (M1) Removal ........................................................................... 84
Paper Guide Drive Motor (M3) Removal ............................................................. 85
Transfer Switch Solenoid (SL1) Removal ........................................................... 86
Paper Guide Home Position Sensor (PC2) Removal .......................................... 87
Bin 1 Shift Home Position Sensor (PC4) Removal .............................................. 88
Paper Empty Sensor Board (PWB-B/D1-3/E) Removal ...................................... 89
Eject Sensor Board (PWB-C) Removal ............................................................... 90
Shift Guide Plate Removal .................................................................................. 91
Eject Roller Shaft Removal ................................................................................. 92
Bin 1 Eject Roller Shaft Removal ....................................................... 92
Bin 2 Eject Roller Shaft Removal ....................................................... 92
Bin 3 - 5 Eject Roller Shaft Removal .................................................. 93
Movable Paper Guide Removal .......................................................................... 94
Transfer Switch Guide Lever Removal ................................................................ 95
Bin 4 /Bin 5 Switch Guide Lever Removal ........................................................... 95
Maintenance of the 5-Bin Unit ....................................................................... 96
Maintenance Items .............................................................................................. 96
Cleaning the Paper Take-up Roller ..................................................................... 96
Exploded Diagrams for 5-Bin Unit ................................................................. 96
Housing ............................................................................................................... 96
Paper Exit Section ............................................................................................... 98
Paper Transport Section (A) .............................................................................. 100
Paper Transport Section (B) .............................................................................. 102
Paper Transport Section (C) ............................................................................. 104
10-bin Unit
Installing the 10-bin Unit ............................................................................. 107
Installing the 10-bin Unit .................................................................................... 107
Levelness Adjustment of the 10-bin Unit ........................................................... 113
Disassembly and Assembly of the 10-bin Unit ............................................. 114
Outer Cover Removal ....................................................................................... 114
Tray Section Disassembly/Assembly ................................................................ 115
Transport Motor (M1) Removal ........................................................ 115
Transport Motor Pulse Detection Switch (PC1) Removal ................ 116
Sorter Set Switch (S1) Removal ....................................................... 117
Controller Board (PWB-A) Removal ................................................. 117
Sort/Non-Sort Switch Solenoid (SL1) Removal ................................ 118
Solenoid Assembly (SL2, SL3) Removal ......................................... 118
Bin 1/Bin 6 Paper Empty Sensor Board Removal (PWB-B/D5) ....... 119
Paper Empty Sensor Board (PWB-D1-D4, D6-D9) Removal ........... 120
Eject Sensor Board (PWB-C) Removal ............................................ 121
Vertical Transport Roller Removal ................................................... 122
Eject Roller Removal ........................................................................ 123
Bin Switch Guide Removal ............................................................... 124
Eject Guide Removal ........................................................................ 125
Sort/Non-Sort Switch Guide Removal .............................................. 126
Transport Roller Removal ................................................................ 127
Horizontal Transport Unit Disassembly/Assembly ............................................ 128
Rear Cover Removal ........................................................................ 128
Non-Sort Bin Jam Sensor (PC1) Removal ....................................... 128
Horizontal Transport Door Sensor (PC4) Removal .......................... 129
Horizontal Transport Unit Paper Empty Sensor (PC6) Removal ...... 129
Paper Path Switch Solenoid Removal .............................................. 130
Horizontal Transport Roller Removal ............................................... 131
Adjustment ................................................................................................. 132
Timing Belt Tension Adjustment ....................................................................... 132
Test Mode ......................................................................................................... 132
Pre-Operation ................................................................................... 132
Activating the Test Mode .................................................................. 133
Cancelling the Test Mode ................................................................. 133
Details of Each Test Mode ............................................................... 133
Adjusting the Eject Sensor ................................................................................ 139
Maintenance ............................................................................................... 140

Maintenance Items ............................................................................................ 140
Cleaning the Paper Take-up Roller ................................................................... 140
Exploded Diagrams .................................................................................... 141
Housing ............................................................................................................. 141
Frames .............................................................................................................. 143
Paper Transportation Section (A) ...................................................................... 145
Paper Transportation Section (B) ...................................................................... 147
Paper Transportation Section (C) ...................................................................... 149
Paper Transportation Section (D) ...................................................................... 151
Paper Transportation Section (E) ...................................................................... 153
Drive Section ..................................................................................................... 155
Horizontal Transport Unit (A) ............................................................................. 157
Horizontal Transport Unit (B) ............................................................................. 159
Operating principles
Double Cassette Unit .................................................................................. 162
Structure ............................................................................................................ 162
Drive System .................................................................................... 162
Electrical Components Layout .......................................................... 162
Mechanical Operations ...................................................................................... 163
Paper Size Regulating Plate ............................................................ 163
Paper Lifting Plate ............................................................................ 163
Paper Size Setting ............................................................................ 163
Paper Near Empty Detection ............................................................ 164
Paper Empty Detection .................................................................... 164
Paper Separation Mechanism .......................................................... 165
Paper Take-up Roller ....................................................................... 166
Paper Take-Up Retry Control ........................................................... 166
Duplex Unit ................................................................................................. 167
Structure ............................................................................................................ 167
Drive System .................................................................................... 167
Electrical Components Layout .......................................................... 168
Mechanical Operations ...................................................................................... 168
Switchback Mechanism .................................................................... 168
Transport/Feedback Mechanism ...................................................... 169
Duplex Print Schemes ...................................................................... 170
LCC Unit Unit .............................................................................................. 172
Structure ............................................................................................................ 172
Drive System Layout ........................................................................ 172
Electrical Components Layout .......................................................... 173
Mechanical Operation ....................................................................................... 174
Vertical Transport Mechanism .......................................................... 174
Paper Take-up Mechanism .............................................................. 175
Paper Take-Up Retry Control ........................................................... 178
Paper Separating Mechanism .......................................................... 179
Paper Pressure Releasing Mechanism ............................................ 180
Paper Take-up Roller Retracting Mechanism .................................. 180
Paper Size Regulating Plate ............................................................ 181
Paper Size Setting ............................................................................ 181
LCC Set Detection ............................................................................ 182
Lifting Mechanism ............................................................................ 183
Paper Near Empty Detection ............................................................ 185
Paper Empty Detection .................................................................... 185
5-Bin Unit ................................................................................................... 186
Structure ............................................................................................................ 186
Drive Section Layout ........................................................................ 186
Electrical Component Layout ........................................................... 187
Mechanical Operations ..................................................................................... 188
Paper Exit Path ................................................................................ 188
Single/Duplex Print Switch Mechanism ............................................ 189
Paper Guide Mechanism .................................................................. 189
Bin 4/Bin 5 Switch Mechanism ......................................................... 190
Shift Mechanism ............................................................................... 190
Paper Empty Detection Mechanism ................................................. 191
Paper Full Detection Mechanism ..................................................... 192
10-bin Unit .................................................................................................. 193
Structure ............................................................................................................ 193
Drive Section Layout ........................................................................ 194
Electrical Component Layout ........................................................... 195
Mechanical Operations ..................................................................................... 196
Paper Exit Path ................................................................................ 196
Paper Transport Mechanism (Horizontal Transport Unit) ................. 198
Bin Switch Mechanism ..................................................................... 198
Paper Empty Detection Mechanism ................................................. 199
Paper Full Detection Mechanism ..................................................... 199
Mode Description .............................................................................................. 200
Normal Mode (Non-Sort Mode) ........................................................ 200
Large Capacity Mode (Stacker Mode) .............................................. 200
Mailbox Mode ................................................................................... 200
Sorter Mode ...................................................................................... 200
Multiple Sorter Mode ........................................................................ 200



DOUBLECASSETTEUNIT

EPL-N2700 Optional Units Revision A
Double Cassette Unit Installing the Double Cassette Unit 9
1.1 Installing the Double Cassette Unit
This section describes how to install the Double Cassette Unit to the
printer main body. Note you are required to remove any optional unit
such as the Double Cassette Unit when servicing the printer. The
procedure for removing the Double Cassette Unit is not included since
you can remove it by reversing the installation procedure.
1. Open the packing carton and get a Double Cassette Unit and the
user’s manual.
Figure 1-1. Unpacking
2. Pull out the paper cassette and remove the protection materials.
Figure 1-2. Removing the Protection Pads
3. Turn the printer power off and disconnect the AC power cable and
interface cable.
4. Remove the bottom cover from the bottom part of the printer.
Figure 1-3. Bottom Cover Removal
CAUTION
After removing the packing materials, please keep
them out of children’s reach.

EPL-N2700 Optional Units Revision A
Double Cassette Unit Installing the Double Cassette Unit 10
5. Place the printer main body on the Double Cassette Unit.
Figure 1-4. Placing the Printer on the Double Cassette Unit
6. Attache the bottom cover to the bottom part of the Double Cassette
Unit.
Figure 1-5. Installing the Bottom Cover
7. Secure the corners for the printer and the Double Cassette Unit with
the holders and screws (1603).
Figure 1-6. Attaching the Holders
8. Connect the interface cable and the AC power cable to the printer
and turn the printer on.
CHECK
PO IN T When placing the printer, make sure the following:

The blue levers on the cassette and the printer are
facing in the same direction.

All corners of the printer are properly aligned with
the corresponding ones of the cassette unit.
CAUTION
2 people are required
to lift the printer as
shown in the figure.

EPL-N2700 Optional Units Revision A
Double Cassette Unit Disassembly and Assembly of the Double Cassette Unit 11
1.2 Disassembly and Assembly of the Double Cassette Unit
This section provides the disassembly procedure for the Double
Cassette Unit. Unless otherwise specified, assembly can be performed
by following the disassembly procedure in reverse order.
1.2.1 Paper Take-up Roller Removal
1. Release the lock on the Paper Take-up Roller and slide the roller
along the axle plate to remove the roller.
Figure 1-7. Paper Take-up Roller Removal
1.2.2 Paper Empty Sensor Removal
1. Release three hooks attaching the holder to the guide plate and
remove the holder. (See Figure 1-8.)
2. Remove the screw (3501) securing the paper empty sensor bracket
to the guide plate. (See Figure 1-8.)
3. Remove the stopper for the Paper Empty Sensor and remove the
sensor. (See Figure 1-8.)
4. Disconnect the harness from the Paper Empty Sensor.
CHECK
PO IN T When installing the Paper Take-up Roller, ensure the
roller is securely locked as shown in the figure below.
CAUTION
If you have replaced the Paper Take-up Roller, perform
“LC2 Counter Clear” in the maintenance menu. In case
2 Double Cassette Unit are connected, perform “LC3
Counter Clear” as well.

EPL-N2700 Optional Units Revision A
Double Cassette Unit Disassembly and Assembly of the Double Cassette Unit 12
1.2.3 Paper Near Empty Sensor Removal
1. Release three hooks attaching the holder to the guide plate and
remove the holder.
2. Remove the screw (3501) securing the paper near empty sensor
bracket to the guide plate.
3. Remove the stopper for the Paper Near Empty Sensor and remove
the sensor.
4. Disconnect the harness from the Paper Near Empty Sensor.
1.2.4 Paper Feed Sensor Removal
1. Remove the screw (3501) securing the paper feed sensor bracket to
the guide plate and remove the bracket.
2. Remove the stopper for the Paper Feed Sensor and remove the
sensor.
3. Disconnect the harness from the Paper Feed sensor.
Figure 1-8. Removal of the Paper Empty / Paper Near Empty / Paper Feed Sensors
9302
3501
3704
3501
3501
3501
3704
9302
3501
S5
S4
3704
3704

EPL-N2700 Optional Units Revision A
Double Cassette Unit Disassembl
y
and Assembl
y
of the Double Cassette Unit 13
1.2.5 Paper Size Sensor (Paper Size Switch)
Removal
1. Remove three screws (3704) securing the paper size sensor
bracket to the frame in the Double Cassette Unit, and remove the
bracket along with the paper size sensor.
2. Remove the screw (3501) securing the paper size sensor cover to
the bracket and remove the cover from the bracket.
3. Release the hook securing the Paper Size Sensor to the inner
bracket and remove the sensor from the bracket.
4. Disconnect the harness from the Paper Size Sensor.
Figure 1-9. Paper Size Sensor Removal
1.2.6 Controller Board (PWB-A) Removal
1. Remove the screw (3727) securing the cover and remove the cover.
2. Remove harnesses from the connectors on the PWB-A.
3. Remove two screws (3501) securing the PWB-A to the bracket and
the PWB support, and remove the PWB-A.
Figure 1-10. PWB-A Removal

EPL-N2700 Optional Units Revision A
Double Cassette Unit Disassembly and Assembly of the Double Cassette Unit 14
1.2.7 Paper Take-up Solenoid Removal
1. Remove the tension spring hooked to the gear 31T.
2. Remove the screw (3501) securing the paper take-up solenoid
cover to the bracket and remove the cover.
3. Remove the screw (3501) securing the Paper Take-up Solenoid to
the bracket and remove the solenoid from the bracket.
4. Disconnect the harness from the connector on the solenoid.
Figure 1-11. Paper Take-up Solenoid Removal

EPL-N2700 Optional Units Revision A
Double Cassette Unit Disassembly and Assembly of the Double Cassette Unit 15
1.2.8 Right Door Set Sensor Removal
1. Remove the tension spring hooked to the gear 31T.
2. Remove two screws (3704) securing the PWB-A board bracket to
the Double Cassette Unit Frame and remove the bracket. (See
Section 1.2.7.)
3. Remove the screw (3501) securing the plate spring to the bracket
and remove the plate spring from the bracket.
4. Remove the following screws:
 Two screws (3704) securing the solenoid bracket to the Double
Cassette Unit Frame.
 Four screws (3704) securing the Paper Take-up Mechanism
(including the axle plate, guide plate, and bracket) to the 2nd
Cassette Frame.
 The screw (3501) securing the rail and axle plate.
5. Lift up the Paper Take-up Solenoid and bracket.
6. Remove two screws (3501) securing the solenoid bracket to the
Paper Take-up mechanism and remove the solenoid bracket.
7. Remove the stopper securing the Right Door Set Sensor to the
solenoid bracket.
8. Release the hook fixing the Right Door Set Sensor to the solenoid
bracket and remove the sensor.
9. Disconnect the harness from the connector on the Right Door Set
Sensor.
Figure 1-12. Right Door Set Sensor Removal

EPL-N2700 Optional Units Revision A
Double Cassette Unit Maintenance of the Double Cassette Unit 16
1.3 Maintenance of the Double Cassette Unit
The maintenance method of the Double Cassette Unit is mostly the
same as for the printer body. Therefore, this section only describes the
method specific to the Double Cassette Unit.
1.3.1 Cleaning the Paper Take-up Roller
1. Remove the Paper Take-up Roller. (Refer to Section 1.2.1.)
2. Wipe the Paper Take-up Roller with a soft cloth moistened with
water.
Figure 1-13. Cleaning the Paper Take-up Roller
1.3.2 Cleaning the Transport Roller
1. Open the side cover.
2. Wipe the Transport Roller with a soft cloth moistened with water.
Figure 1-14. Cleaning the Transport Roller
CAUTION
Do not use any solvent, including alcohol.

EPL-N2700 Optional Units Revision A
Double Cassette Unit Exploded Diagrams for Double Cassette Unit 17
1.4 Exploded Diagrams for Double Cassette Unit
1.4.1 Housing
Table 1-1. Part List - Housing
No. Part Name No. Part Name
01 GUIDE 17 HOLDER
02 BRACKET 18 SPRING
03 PLATE SPRING 19 BRACKET
04 RUBBER FOOT 20 BRACKET
05 FRAME 21 SHOULDER SCREW
06 COVER 22 SWITCH, SIZE (S1)
07 GROUND PLATE 23 HARNESS
08 BRACKET 24 COVER
09 HARNESS 25 RUBBER FOOT
10 BRACKET 26 BRACKET
11 PW BOARD-A, MAIN (PWB-A) 27 BRACKET
12 PWB SUPPORT 6.35H 28 RAIL
13 HARNESS 29 PLATE SPRING
14 BRACKET 30 BRACKET
15 SHOULDER SCREW 31 HOLDER
16 RUBBER FOOT − −

EPL-N2700 Optional Units Revision A
Double Cassette Unit Exploded Diagrams for Double Cassette Unit 18
01
06 05
11 08
09
10
14
13
15 15
12 07
24
19
17
18
22
23
20 21
21
31
03
02 16
25
03
02
26
27 28
25 29 30
04
PWB-A
S1 3714
3704
3704
3704
3704
3714
3704
3501
3501
3501
3704
3704
3704
3704
3501
3727
3704
1603

EPL-N2700 Optional Units Revision A
Double Cassette Unit Exploded Diagrams for Double Cassette Unit 19
1.4.2 Paper Take-up Section
Table 1-2. Part List - Paper Take-up Section
No. Part Name No. Part Name
01 GUIDE PLATE 21 BUSHING
02 HOLDER 22 GEAR 34T
03 POLYESTER FILM 23 HARNESS
04 COLLAR 24 HOLDER
05 ROLLER 25 BRACKET
06 SHAFT 26 LEVER
07 AXLE PLATE 27 AXLE PLATE
08 ROLLER 28 SPACER
09 BUSHING 29 TORSION SPRING
10 GEAR 30/36T 30 BRACKET
11 GEAR 31T 31 TORSION SPRING
12 TENSION SPRINT 32 ACTUATOR
13 PHOTO INTERRUPTER (2S-5) 33 BRACKET
14 BRACKET 34 COLLAR
15 SOLENOID, TAKE-UP (SL1) 35 BRACKET
16 BRACKET 36 SHAFT
17 STOPPER 37 ACTUATOR
18 GEAR 16/20T 38 TORSION SPRING
19 GEAR 20T 39 GUIDE PLATE
20 GEAR 18T 40 GUIDE

EPL-N2700 Optional Units Revision A
Double Cassette Unit Exploded Diagrams for Double Cassette Unit 20
01
02
03
36
37
38
05
07
05
02
03
04
06
09
10
11
12
13
20
21
19
19
18
17
14
15
16
22
22
23
27
17 24
13
08
28
28
26
29
30
31
32
13
25
17
33
21
13
35
17
34
04
39 40
40
1208
9302
9302
9301
3501
3501
3501
3501
3704
3501
3501
3501
3704
9302
3501
SL1
S2
S5
S4
S3
3704
3704