Epson LX-810 User manual

Y46399114002

EPSON
LX-810
No part of this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, mechanical, photocopying, recording, or otherwise, without
the prior written permission of Seiko Epson Corporation. No patent liability is assumed with
respect to the use of the information contained herein. While every precaution has been
taken in the preparation of this book, Seiko Epson Corporation assumes no responsibility for
errors or omissions. Neither is any liability assumed for damages resulting from the use of
the information contained herein.
Neither Seiko Epson Corporation nor its affliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs or expenses incurred by purchaser or third
parties as a result of: accident, misuse, or abuse of this product or unauthorized
modifications, repairs, or alterations to this product.
Seiko Epson Corporation and its affiliates shall not be liable against any damages arising
from the use of any options other than those designated as Original Epson Products or
Epson Approved Products by Seiko Epson Corporation.
Epson and Epson ESC/P are registered trademarks of Seiko Epson Corporation,
SmartPark is a trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and
may be trademarks of their respective companies.
Copyright © 1991 by Epson America, Inc. Torrance, California
All rights reserved.
User’s Guide

For United States Users
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio or
television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will
invalidate the FCC Certification of this device and may cause interference levels which
exceed the limits established by the FCC for this equipment. It is the responsibility of the
user to obtain and use a shielded equipment interface cable with this device. If this
equipment has more than one interface connector, do not leave cables connected to unused
interfaces.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
For Canadian Users
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the radio interference regulations of the Canadian Department
of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites
applicables aux appareils numeriques de Classe B prescrites dans le reglement sur le
brouillage radioelectrique edicte par le Ministere des Communications du Canada.
ii

Tips for printing on single sheets
There are a few things you should know about printing on single
sheets as opposed to continuous paper. When you print on single
sheets, you may notice that your printer prints the first page of
your file correctly but then prints too low on the next page, or
that it prints the last few lines from one page onto the next.
These differences in print position are easy to adjust; you can
simply change some of the settings in your application program as
described below to get the right results.
1. When you install an application program, it normally asks you
what printer you are using. Make sure you choose the correct
printer. See Chapter 1 for the right printer to choose.
2. Many programs include an option to set the maximum lines per
page. If your program has a lines-per-page setting and you are
using standard 8½ X 11-inch paper, set the lines per page to
61.
Note: To find the right lines-per-page setting for paper that is
not 8½ X 11, create a test document using your application
program. Set your top and bottom margins to 0 and then create
a file of numbered lines from 1 to 66. When you print your file,
notice the last number printed on the first page. This is your
maximum lines-per-page setting.
3. If your program doesn’t have a lines-per-page setting, try
decreasing the top margin or increasing the bottom margin, or
both, until you get the results you want.
4. You can also try adjusting the form length setting. For a
standard 8½ X 11-inch page, try setting the form length at 10
inches.
5. Some programs also let you indicate whether you are using
single sheets or continuous paper. Make sure you choose single
sheets.
iii

Where to Get Help for United States Users
Epson America provides local customer support and service
through a nationwide network of authorized Epson dealers and
Service Centers.
Epson also provides the following support services through the
Epson Consumer Resource Center at [phone]:
Assistance in locating your nearest Authorized Epson Reseller or
Service Center
Technical assistance with the installation, configuration, and
operation of Epson products
Epson technical information library fax service
Product literature with technical specifications on our current
and new products
Sales of ribbons, supplies, parts, documentation, and accessories
for your Epson product
Customer Relations.
iv

IMPORTANT SAFETY INSTRUCTIONS
1. Read all of these instructions and save them for later reference.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table.
The product may fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the
product and to protect it from overheating, these openings
must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or
over a radiator or heat register. This product should not be
placed in a built-in installation unless proper ventilation is
provided.
7. This product should be operated from the type of power source
indicated on the marking label. If you are not sure of the type
of power available, consult your dealer or local power
company.
8. This product is equipped with a 3-wire grounding-type plug, a
plug having a third (grounding) pin. This plug will only fit into
a grounding-type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the
purpose of the grounding-type plug.
9. Do not locate this product where the cord will be walked on.
V

10. If an extension cord is used with this product, make sure that
the total of the ampere ratings on the products plugged into
the extension cord does not exceed the extension cord ampere
rating. Also, make sure that the total of all products plugged
into the wall outlet does not exceed 15 amperes.
11. Never push objects of any kind into this product through
cabinet slots, as they may touch dangerous voltage points or
short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
12. Except as specifically explained in the User’s Manual, do not
attempt to service this product yourself. Opening or removing
those covers that are marked “Do Not Remove” may expose
you to dangerous voltage points or other risks. Refer all
servicing in those compartments to service personnel.
13. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the
operating instructions are followed. Adjust only those
controls that are covered by the operating instructions, since
improper adjustment of other controls may result in damage
and will often require extensive work by a qualified
technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been
damaged.
F. If the product exhibits a distinct change in performance,
indicating a need for service.
vi

Introduction
1
Features ........................................................................................
1
Options ........................................................................................ 2
Finding Your
Way Around..
......................................................
2
Warnings,
Cautions,
and Notes ................................................
3
Name
of the Parts.. .....................................................................
4
Chapter 1 Setting Up the Printer l-l
Unpacking the Printer
............................................................
1-2
Choosing
a Place for the Printer.. .........................................
1-3
Assembling the Printer..
.........................................................
1-5
Testing
the Printer..................................................................
1-10
Connecting
the Printer to Your Computer..........................
1-13
Setting
Up Your Application
Software ................................
1-14
Chapter 2 Paper Handling 2-l
Using Single Sheets
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
Using Continuous
Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
Adjusting the
Loading Position
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
Switching Between Continuous and Single Sheets . . . . . . . . . . . . 2-8
Printing
on Special Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-10
Chapter 3 Using the Printer 3-1
Operating
the Control Panel
................................................. 3-2
Setting
the DIP Switches
....................................................... 3-5
Selecting Typestyles ............................................................... 3-9
Selecting
an International Character
Set.............................. 3-11
Choosing
a Character Table .................................................. 3-12
Chapter 4 Using the Printer Options 4-1
Cut-Sheet
Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
Pull
Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9
Roll
Paper Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .., . . . . . . . . . . . . . . .
4-14
Interface Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-17
vii

Chapter 5 Maintenance 5-1
Cleaning the Printer ............................................................... 5-2
Replacing the
Ribbon............................................................. 5-3
Transporting the Printer
........................................................ 5-4
Chapter 6 Troubleshooting 6-1
Problems and Solutions.......................................................... 6-2
Power Supply .......................................................................... 6-3
Printing ..................................................................................... 6-4
Paper Handling
....................................................................... 6-8
Options .................................................................................... 6-10
Chapter 7 Technical Specification 7-1
Printer Specifications.. ............................................................ 7-2
Interface Specifications........................................................... 7-7
Initialization
............................................................................. 7-10
Chapter 8 Command Summary 8-1
Using the Command Summary
. . . . . . . . . ...................................
8-2
Commands Arranged by Topic
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .....
8-3 __
Appendix
A-1 ~
Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2
Glossary
GL-1
Index
IN-1
Viii

Introduction
Your new Epson 9-pin dot matrix printer combines a compact
design and high performance with a wide range of features.
Features
In addition to the high-quality printing and ease of operation you
have come to expect from Epson printers, your printer offers the
following:
Easy paper handling, featuring automatic single-sheet loading.
Fast draft printing of up to 240 characters per second at 12 cpi.
Two built-in Near Letter Quality fonts (Roman and Sans Serif)
for producing high-quality documents,
A convenient control panel design that allows direct selection
of fonts, as well as a choice of normal or condensed printing.
The SmartParkTM paper handling system that lets you use
single sheets of paper without removing continuous paper,
eliminates paper waste with short tear-off, and allows easy and
accurate paper alinment.
Compatibility with the Epson ESC/P® commands used by the
Lx-800.
A micro-adjustment feature that allows you to feed the paper
forward or backward to finely adjust the paper loading and
short tear-off positions.
Thirteen international character sets, an italic character table,
and the five PC character tables.
Introduction 1