Epson TM-T88IV ReStick User manual

One Blue Hill Plaza, 16th Floor, PO Box 1546
Pearl River, NY 10965
1-800-PC-AMERICA, 1-800-722-6374
(Voice) 845-920-0800 (Fax) 845-920-0880
1 | P a g e
Installing the EPSON TM-T88IV
Receipt Restick Printer in Windows
using an Ethernet Connection
This is a step by step guide for installing the Epson TM-T88IV Receipt Restick Printer in
a Windows 32 or 64 bit environment and configuration for use with CRE/RPE.

2 | P a g e
Using a CAT-5 network cable (RJ45 connector) through a router or switch this option
requires the purchase of a router or switch and network cable.
Before you begin, make sure your EPSON TM-
T88IV printer is plugged in and properly
connected to your router/switch via network
cable and that the paper roll is properly
seated.
The other end of the cable should be
connected to the corresponding port on the
back of your receipt printer (see image below).

3 | P a g e
Configuring the Ethernet properties for the Epson printer
Please download the Epson utility from the following link:
http://download2.pcamerica.com/drivers/Epson_Utility_for_Ethernet_Printers.zip
1. Locate the zip file you downloaded
“Epson_Utility_for_Ethernet_Printers.zip” and
extract its contents to a convenient location. Right
click on the extracted file “Wcfg300a.exe” and select
Run as administrator (XP users, simply double-click
on the extracted file). Follow the on screen
instructions to install the Epson TMNet WinConfig
Version 3.00. Select Next.
2. Select I accept the terms of the license agreement.
Select Next.

4 | P a g e
3. Select Next.
4. Select Next.
5. Select Install.

5 | P a g e
6. Select Finish.
Select Start, point to Programs, point to EPSON
TMNet WinConfig, then select TMNet WinConfig
Ver3.00 to start the configuration utility.
1. Select Ethernet.
2. Select the printer detected by the application that
you want to assign an IP address to.
3. Select Configuration.

6 | P a g e
1Select the TCP/IP tab.
2Select Manual for IP Address Setting.
3Select Set using PING.
4Assign the IP address, the Subnet mask, and the
Default gateway.
Ask your administrator for the IP address and the
Default gateway to be set.( In our example we are
using an IP Address of 172.25.2.49, Subnet Mask of
255.255.252.0, and Default Gateway of 172.25.0.1.)
5Select OK.
6Select Yes.
7Enter the password set in the print server, then
select OK. If you have never set a password,
select OK without entering a password.

7 | P a g e
8Select OK.
9Select OK.
Note: If the printer is not detected you can access the firmware of the printer by opening your
internet browser and entering the following default address:
http://192.168.192.168
Before you begin, make sure your EPSON printer is plugged in, and that the receipt paper roll is
properly seated.

8 | P a g e
Make sure the printer is turned off for the driver installation.
Before you begin please download and extract the installation files from:
http://download2.pcamerica.com/drivers/8/Manufacturer/Epson/APD_454aE.zip
Locate the zip file you downloaded
“APD_454aE.zip” and extract its contents to a
convenient location. Right click on the extracted file
“APD_454aE a.exe” and select Run as administrator
(XP users, simply double-click on the extracted file).
1. Select Next to begin the installer.
2. Select I accept the terms in the license agreement
and select Next.

9 | P a g e
3. Select Minimum (Recommended), then hit Next.
4. Select Add.
5. Under the Select driver dropdown, locate and
select EPSON TM-T88IV ReStick. The Printer name
should auto fill EPSON TM-T88IV ReStick.
6. Under Port type, locate and select Create an
Ethernet port.
7. Hit Next.

10 | P a g e
8. Enter the IP address configured in step 4 of page 6.
(In our example, we assigned the printer an IP
address of 172.25.2.49.)
9. Select Next.
10. Select Next.
11. Select Next.