Epson SuperColor F3070 User manual

Epson® SureColor® F3070
Handling and Unpacking Instructions
*Forklift and Hand Jack
Handling Information
*No Stacking
UNPACKING Included in the Box 1
Confidential 1

Front
SC-F3070
Handling Information about Forklift and Hand Jack
A mark indicating
Center of Gravity
Lifting around the center of
gravity mark position. Fully
insert the forks.
Length of fork: 6.6 ft or more
SIDE
Length of fork: 6.6 ft or more
Maximum
capacity: 1.65 t
Gross Weight of Main unit 926–1058 lb
FRONT_REAR
C11CH
C-code is at
front right
side only.
Packing size L89×D72×H63 in
L
Main unit
UNPACKING Included in the Box 2
Confidential 1

SC-F3070 （No Stacking)
Note： No Stacking
UNPACKING Included in the Box 3
Confidential 1

SC-F3000 Series
UNPACKING Included in the Box 4
Confidential 2
1.3 Included in the Box
Figure 1-18. Included in the box
List of Items Included in the Package
Bulk Ink Unit Box
Documents
Accessory box
Ramps
Tools
Head Slant Check Jig
Category Item Qty. Explanation
Accessory box
Platen-M set 1 Standard included item
Cloth platen-M 1 Standard included item
Grip Pad Tool 1 Standard included item
Platen frame hook 2 Standard included item
Tweezers 1 Standard included item
Maintenance kit 1 Standard included item
Waste Ink Bottle Stand 1Standard included item
Waste Ink Bottle 1 Standard included item
Hexagon screw 3 Standard included item
Clean-room wiper 100 Standard included item
AC cable 1 Standard included item
Bulk Ink Unit
Box
Bulk Ink Unit 1Bulk Ink Unit main unit
M6 hexagon screw 4 Screws to secure the Anti-tip
plate and the wire.
Anti-tip plate 1 Prevents the Bulk Ink Unit
from tipping over.
USB cable 1
A cable for communication
between the printer and the
Bulk Ink Unit.
AC cable 1 For Bulk Ink Unit
Documents
Document pack 1 CD and documents
Caution label 1 Multilingual ink caution label

SC-F3000 Series
UNPACKING Included in the Box 5
Confidential 2
Tools
Wrench 17" 1 To adjust the height of the
adjusters.
Wrench 19" 2 For the stand fixing bolt.
Hexagon wrench M4 1
Mainly used for securing the
Waste Ink Bottle Stand and for
removing the Right Window
Cover.
Hexagon wrench M6 1 For the Anti-tip plate.
Hexagon wrench M10 1 For the CR fixing jig.
Hand jack 1 For removing the wood
chocks.
Tools
Waste ink tank cover
magnet 1A magnet to secure the Waste
ink tank cover.
Waste ink tank cover
magnet fixing screws 2Screws to secure the Waste ink tank cover magnet.
Head Slant Check
Jig Head Slant Check Jig 1 Gauge for checking the printhead for slant.
Ramps Ramps 2Use to bring the printer down
from the pallet.
Category Item Qty. Explanation
Ink Ink pack boxes
(7 total included with
printer)
1
1
1
1
2
1
Cyan
Magenta
Yellow
Black
White
Maintenance Liquid

SC-F3000 Series
UNPACKING Unpacking and Install 6
Confidential 2
1.5 Unpacking and Install
1. Remove the packing of carton box using the cutter.
Figure 1-20. Removing the packing material
Figure 1-21. Releasing the PP bands
3. Remove the 12 joints.
Packing
(Plastic wrap)
PP bands
[How to remove the joints]
Insert your finger into the hole and remove the joint
while lifting and pulling it.
Note: Requires 4 delivery people and 1 forklift operator (total of 5).
2. Release the two PP bands.
IMPORTANT: Carrier must take photos of all four sides
and top of the box as it is being offloaded from the truck. If
you notice damage to the box or pallet, please take close-up
photos. If photos are not provided, Carrier may be liable for
damages.
Please email photos to [email protected] with
the subject line being the printer serial number. See page 15
for serial number location and additional instructions.

SC-F3000 Series
UNPACKING Unpacking and Install 7
Confidential 2
Figure 1-22. Removing the joints
4. Remove the top cover.
Figure 1-23. Removing the top cover
Figure 1-24. Removing the cardboard enclosure
Joints
Joints
Top Cover
Cardboard
enclosure
5. Remove the cardboard enclosure.

SC-F3000 Series
UNPACKING Unpacking and Install 8
Confidential 2
6. Unload the two empty boxes.
Figure 1-25. Unloading the empty boxes
7. Remove the protection parts (styrofoam).
Figure 1-26. Removing the protection parts
8. Unload the accessories box.
Figure 1-27. Unloading the accessories box
Empty boxes
Protection parts
Accessories
box
Note: Do not open the accessories box. Be sure to keep the accessories box with the
main printer unit.

SC-F3000 Series
UNPACKING Unpacking and Install 9
Confidential 2
9. Remove the top cover of Bulk Ink Unit.
Figure 1-28. Removing the top cover
10. Remove the cardboard enclosure of Bulk Ink Unit.
Figure 1-29. Removing the cardboard enclosure
[How to remove the top cover of the Bulk Ink Unit]
Cut the four corners of the top cover with a box
cutter and remove it.
Top Cover of Bulk Ink
Unit
[How to remove the cardboard enclosure of the Bulk
Ink Unit] With a box cutter, cut the right front corner
of the box as viewed from the front, and remove it.
Cardboard enclosure of
Bulk Ink Unit
Right front corner

SC-F3000 Series
UNPACKING Unpacking and Install 10
Confidential 2
11. Remove the two protection parts (styrofoam).
Figure 1-30. Removing the protection parts
12. Carefully unload the Bulk Ink Unit from the pallet and be sure to keep all of the
parts together.
Figure 1-31. Unloading the Bulk Ink Unit
Protection parts
Make sure to lift the Bulk Ink Unit using two people.
Hold position
Hold positionLeft
Bulk Ink Unit
Plastic sheet

SC-F3000 Series
UNPACKING Unpacking and Install 11
Confidential 2
13. Remove the three protection parts (styrofoam).
Figure 1-32. Removing the protection parts
14. Unload the two ramps and tools from pallet.
Figure 1-33. Unload the two rampsand tools
15. Remove the four bolts from the Stand with #13 wrench.
Figure 1-34. Removing the bolts
Protection parts
Tools
Left
Ramps
Left Bolts
BoltsRight
Be sure to place the pallet on the same level or within
wheeling distance of the printer's final installation
location. The printer cannot be lifted by forklift or by
hand once removed from the pallet.

SC-F3000 Series
UNPACKING Unpacking and Install 12
Confidential 2
16. Remove the four nuts from pallet with two #19 wrenches.
Insert the #19 wrench into hole and lock the bolt then remove the nut with
another #19 wrench.
Figure 1-35. Removing the nuts
17. Remove the four fixing parts.
Figure 1-36. Removing the fixing parts
Left
Nuts
Nut
Hole
#19 wrenchs
Nuts
Right
Left
Fixing parts
Right
Fixing parts

SC-F3000 Series
UNPACKING Unpacking and Install 13
Confidential 2
18. Make sure the adjusters are up.
Figure 1-37. Checking the adjusters
19. Remove the two bolts from the pallet.
Figure 1-38. Removing the bolts
Adjuster
Left
Bolt
Right
Bolt

SC-F3000 Series
UNPACKING Unpacking and Install 14
Confidential 2
20. Remove the two wood chocks while lifting the printer with the handjack.
Figure 1-39. Removing the wood chocks
Make sure not to pinch your fingers between the stand and the
wood chocks.
When it is difficult to lift the printer, lower the adjuster.
Do not pinch
Adjuster
Push down
Adjuster
Hand jack
Wood chocks

SC-F3000 Series
UNPACKING Unpacking and Install 15
Confidential 2
21. Place the ramps on the front portion of the pallet.
Figure 1-40. Setting the ramps
22. To ensure safety,remove the pallet from the work area after unloading the unit.
Figure 1-41. Move the pallet out of the work area after
unloading the unit.
Ramps
IMPORTANT: Carrier must take photos of all four sides
of the unit and pallet after unpacking. If you notice
damage to the unit or pallet, please take close-up photos
before removing the unit from the pallet. If photos are
not provided, Carrier may be liable for damages.
Please email photos to [email protected]
with the subject line being the printer serial number. The
serial number is located on the back right-side of the unit
when viewed from the front.

SC-F3000 Series
UNPACKING Unpacking and Install 16
Confidential 2
23. Unload the printer with an observer and four supporters.
Four supporters grip the hold positions and move the printer.
A technician supports them to unload the printer for safety.
Figure 1-42. Unloading the printer
24. Install the printer in customer's site at designated indoor
location.
25. Remove the protection parts inside of printer.
Make sure to unload the printer with an observer and four
supporters.
[Hold positions]
Observer
Supporters
Supporters
07/12/2021 ver. 5
Once the unit is on the ground, do not attempt to lift it with a
forklift or by hand. Always use the wheels when moving the unit
into position.