Epson TM-P60II User manual

One Blue Hill Plaza, 16th Floor, PO Box 1546
Pearl River, NY 10965
1-800-PC-AMERICA, 1-800-722-6374
(Voice) 845-920-0800 (Fax) 845-920-0880
1 | P a g e
EPSON TM-P60II Receipt Printer
Installation for Windows 7 (32/64BIT)
All manuals and user guides at all-guides.com

2 | P a g e
Table of Contents
TM-P60 Wireless Thermal Printer Information/Requirements
Setting Up the Wireless Printer
Resetting the Printer to Factory Default
Installing the Epson Ethernet Configuration Utility
Configuring the TM-P60 using the EpsonNet Config utility
Installing the Epson Printer Driver
Configuration in CRE/RPE
All manuals and user guides at all-guides.com

3 | P a g e
TM-P60II Wireless Thermal Printer Information/Requirements
Requirements:
1. An available wireless network:
This network must be setup and configured prior to any configuration from pcAmerica.
The following network types are supported with the use of the TM-P60II Thermal
Receipt Printer:
oWPA Encryption (TKIP)
2. Information on the wireless network which you will be connecting the printer to:
SSID (or network name)
Wireless Password
Subnet mask of the network
IP Address of the router (Default Gateway)
3. A laptop or PC for configuration of the device.
All manuals and user guides at all-guides.com

4 | P a g e
Setting Up the Wireless Printer
1. On the right side of the printer we will need to
locate the battery door.
2. Press the lever and open the door.
3. Insert the battery into the compartment.
All manuals and user guides at all-guides.com

5 | P a g e
4. Plug the power cable into the power brick and the
other end of the power cable into a power source
(wall outlet).
All manuals and user guides at all-guides.com

6 | P a g e
5. Plug the other end of the cable into the port on
the left side of the printer.
All manuals and user guides at all-guides.com

7 | P a g e
6. Loosen the cover (trident symbol) of the mini USB
port located on the top left of the printer.
7. Locate the Mini USB to USB-A cable.
All manuals and user guides at all-guides.com

8 | P a g e
8. Attach the Mini USB connector to the
corresponding port on the receipt printer.
9. Attach the USB-A connector (other end of the
cable) to an available USB port on your computer.
Note: The USB connection is used to configure the
TM-P60II wireless connection. The TM-P60II can
only be used with CRE/RPE through your WiFi
network.
All manuals and user guides at all-guides.com

9 | P a g e
Resetting the Printer to Factory Default
Before doing any configuration on the device we must first reset it back to factory defaults.
1. Press the button on the top right of the printer, to
release the paper roll cover.
2. Press and hold the FEED button and press the
POWER button, to power on the printer.
3. When the printer has powered on, press the FEED
button 6 times, then close the paper roll cover.
Note: When closing the paper cover, make sure the
paper is in between the guides so that it can be ejected
properly.
All manuals and user guides at all-guides.com

10 | P a g e
4. The SELF-TEST page will then be printed.
5. To initialize the printer, open the paper roll cover,
press the FEED button 1 time, then close the paper
roll cover.
6. Initialize will then print on the receipt paper and the
paper roll will then be cut. This will start the factory
reset process.
7. The printer will restart after initialization has
completed.
All manuals and user guides at all-guides.com