Equinox Systems EQLED064 User manual

EQUINOX
GYROCOPTER
!
!
ORDER CODE: EQLED064
-------------------User manual
!
Contents
1. Safety Instructions
2. Features & Specifications
3. How To Set The Unit
4. Troubleshooting
5. Fixture Cleaning

1. Safety Instructions
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another
user be sure that they also receive this.
Unpack and check carefully that there is no transportation damage before using
the unit.
!Before operating, ensure that the voltage and frequency of the power supply
match the power requirements of the unit.
!It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
!The unit is for indoor use only. Use only in a dry location.
!The unit must be installed in a location with adequate ventilation, at least 50cm
from adjacent surfaces. Be sure that no ventilation slots are blocked.
!Disconnect the mains power before replacement or servicing.
!Make sure there are no flammable materials close to the unit while operating as
they may cause a fire hazard.
!Always use a safety cable when installing this unit.
!The maximum ambient temperature is: 40°. Don’t operate it where the
temperature is higher than this.
!In the event of a serious operating problem stop using the unit immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
!Do not touch any power cables during operation as the high voltage may cause
an electric shock.
Warning
!To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.
!Do not open the unit within five minutes after switching off.
!The housing and lenses must be replaced if they are visibly damaged.
!This lighting fixture is for professional use only - it is not designed for or suitable
for household use. The product must be installed by a qualified technician in
accordance with local territory regulations. The safety of the installation is the
responsibility of the installer. The fixture presents risks of severe injury or death
due to fire hazards, electric shock and falls.
!Warning! Risk Group 2 LED product according to EN 62471. Do not view the
light output with optical instruments or any device that may concentrate the
beam.
!WARRANTY: One year from date of purchase.
Installation
The unit should be mounted via its screw holes onto the bracket. Always ensure
that the unit is firmly fixed to avoid vibration and slipping while operating. Make
sure that the structure to which you are attaching the unit to is secure and is able
to support a weight of 10 times of the unit’s weight. Always use a safety cable that
can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be installed by professionals and it must be installed in a
place where is out of the reach of people and no one can pass by or under it.
Please read the instructions carefully as they include important
information about installation, usage and maintenance.

2. Features &Technical Specifications
◇Control: Sound active, Auto, Master/slave and DMX 512 modes
◇DMX Channels: 6CH/14CH/19CH/20CH
◇Electronic dimming:0-100%
uVoltage: 100V~240V, 50/60Hz
uFuse: T 2.5A
uPower consumption: 120W
uLight source: 8 x 8W RGBW 4IN1 LED
uDimension: 212*335*130mm
uWeight: 3.9kg
uPan/Tilt: 540°/360° Infinite
uPower sockets: IEC IN/OUT
uXLR sockets: 3-pin XLR IN/OUT
3.How To Set The Unit
3.1 Control panel
Display
Shows the various menus and selected functions
Button
MENU
Selects the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
Confirms the selected functions
Mains input
Connection to the power supply.
DMX input/output
For DMX 512 linking. Use a 3-pin XLR cables to link to the controller or to other
units.
3.2 Main Functions
To select any of the given functions, press the MENU button up to where the
required function is showing on the display. Select the function by pressing the
ENTER button and the display will blink. Use the DOWN and UP buttons to
change the mode. Once the required mode has been selected, press the ENTER
button to confirm.

The main functions are as below:
DMX Address Setting
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to choose the address to
confirm.
Channel Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (6
Channel) mode, (14 Channel) mode, (19 Channel) mode or
(20 Channel) mode. Once the mode has been selected, press the
ENTER button to confirm.
Slave Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (Slave 1),
(Slave 2) mode, Once the mode has been selected, press the ENTER
button to confirm.
Show Mode
Select , press the ENTER button and the current mode will blink
on the display. Use the DOWN and UP buttons to select from
to . Once the mode has been selected press the ENTER button
to confirm.

AUTO Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP button to select the show from
to !mode to choose to AUTO mode. For speed selecting, Use the DOWN
and UP buttons to select the speed from to mode, Once the
mode has been selected, press the ENTER button to confirm.
Sound Mode
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (sound on)
or (sound off) mode. Once the mode has been selected, press the
ENTER button to confirm.
Sound Sensitivity
Press the MENU and use the UP and DOWN buttons to select and
select the sound sensitivity between value 0 and 100. Press the ENTER button to
confirm.
Led Display
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (Led
display on) or (Led display off) mode. Once the mode has been selected,
press the ENTER button to confirm. To go back to the functions without any
changes press the MENU button again. Press and hold the MENU button for one
second or wait for one minute to go back to the main menu.
Display Inversion
Press the MENU button to select . Press the ENTER button to change the
mode (display normal), it will be automatically saved after 8 seconds. Press
the ENTER button again to select the mode (display inversion). To go back
to the functions press the MENU button. Press and hold the MENU button for one
second or wait for one minute to go back to the main menu.
Display normal mode is for floor standing the unit.
Display inversion mode is for hanging the unit upside down.
Pan setting
Press the MENU button to select . Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (normal)
or (tilt inversion) mode. Once the mode has been selected, press the
ENTER button to confirm.
Tilt1 Inversion
Press the MENU button to select . Press the ENTER button and the display
will blink. Use the DOWN and UP buttons to select the (normal) or
(tilt inversion) mode. Once the mode has been selected, press the ENTER
button to confirm.
Tilt 2 Inverse
Press the MENU button to select. Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the (normal)
or (tilt inversion) mode. Once the mode has been selected, press the
ENTER button to confirm.

Auto Test
To select the Auto Test, press the ENTER button to show AUTO TEST on the di
splay and the unitwill run a selftest. To go back to the functions without any chan
ges press the MENU button again.Hold and press the MENU button for one seco
nd or wait for one minute to exit the menu mode.
Hours
To select the Fixture Hours, press the ENTER button to show FIXTURE HOURS
on the display and,the display will show the number of working hours of the unit.
To go back to the functions without,any changes press the MENU button again.
Hold
and press the MENU button for one second or10Await for one minute to exit the
menu mode.
Software version
Press the MENU button up to when the is blinking on the display. Pressing
ENTER button and the display will show the version of software of the unit. To go
back to the functions press the MENU button.
Reset
Press the MENU button to select . Press the ENTER button and all
channels of the unit will return to their standard position.
1. Master/slave built-in preprogram function
2. Universal DMX controller
There is no need to turn the unit off when you change the DMX address as new
DMX address setting will take effect at once. Every time you turn the unit on, it will
show “MB80”on the display and move all the motors to their ‘home’ position and
you may hear some noises for about 20 seconds. After that the unit will be ready
to receive a DMX signal or run the built in programs.
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other
units to give an automatic, sound activated, synchronized light show. This
function is good when you want an instant show. You have to set the first unit as
master and select show 1, show 2, show 3 or show 4 etc. from the Show Mode.
The other units must be set to either Slave 1 (normal) or Slave 2 (2 light show)
mode. A DMX cable between the units for daisy chaining is needed.
2-light show
In slave mode, Slave 1 means the unit works normally and Slave 2 means
2-light show. In order to create a great light show, you can set Slave 2 on the
second unit to get contrast movement to each other, even if you have two units
only.
4.2 DMX Controller
By using a universal DMX controller to control the units, you will need to set a
DMX address from 1 to 512 so that the units can receive a DMX signal. Press the
MENU button until is showing on the display. Press the ENTER button
and the display will blink. Use the DOWN and UP buttons to change the DMX-512
address. Once the address has been selected, press the ENTER button to
confirm.
Please refer to the below diagram to address your first 4 units：
Channel
mode
Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
8 channel
1
9
17
25
14 channel
1
15
29
33
19 channel
1
20
39
57
20 channel
1
21
61
81

4.3 DMX 512 Configuration
6 channel
Channel
Function
Value
Percent / Setting
1
Dimmer
000-255
0%~ 100%
2
Strobe
000-007
Open
008-255
Strobe Speed
3
Macro Movement
000-007
No function
008-022
Movement01
023-037
Movement02
038-052
Movement03
053-067
Movement04
068-082
Movement05
083-097
Movement06
098-112
Movement07
113-127
Movement08
128-142
Movement09
143-157
Movement10
158-172
Movement11
173-187
Movement12
188-202
Movement13
203-217
Movement14
218-232
Movement15
233-247
Movement16
248-255
Sound active
4
Movement Speed
000-255
Movement Speed slow to fast
5
Color Chase
000-014
No Function
015-035
Colour Chase 1
036-056
Colour Chase 2
057-076
Colour Chase 3
078-097
Colour Chase 4
098-117
Colour Chase 5
118-138
Colour Chase 6
139-159
Colour Chase 7
160-179
Colour Chase 8
180-200
Colour Chase 9
201-220
Colour Chase 10
221-241
Colour Chase 11
242-255
Colour Chase 12
6
Chase Speed
000-255
Slow to fast
14 channel
Channel
Value
Function
1
000-255
Pan
2
000-255
Pan speed slow to fast
3
000-255
Tilt1
4
Tilt1 Rotate
000-005
Stop
006-126
Movement forward fast -> slow
127-128
Stop
129-249
Movement forward Slow -> Fast
250-255
Stop
5
000-255
Colour1
6
000-255
Colour2
7
000-255
Colour3
8
000-255
Colour4
9
000-255
Tilt2
10
Tilt2 Rotate
000-005
Stop
006-126
Movement forward fast -> slow
127-128
Stop

129-249
Movement forward Slow -> Fast
250-255
Stop
11
000-255
Colour5
12
000-255
Colour6
13
000-255
Colour7
14
000-255
Colour8
Colour table for Channel 5/6/7/8/11/12/13/14
Colour
000 - 007 Blackout
008 - 024 R
025 - 041 G
042 - 057 B
058 - 074 W
075 - 090 R + G
091 - 107 R + B
108 - 123 R + W
124 - 140 G + B
141 - 156 G + W
157 - 173 B + W
174 - 189 R + G + B
190 - 206 R + G + W
207 - 222 R + B + W
223 - 239 G + B + W
240 - 255 R + G + B + W
19 channel
Channel
Value
Function
1
000-255
Dimmer
2
000-007
Open
008-255
Strobe speed
3
000-255
Pan
4
000-255
Pan Fine
5
000-255
Pan speed slow to fast
6
000-255
Tilt1
7
000-255
Tilt1 Fine
8
Tilt1 Rotate
000-005
Stop
006-126
Movement forward fast -> slow
127-128
Stop
129-249
Movement forward Slow -> Fast
250-255
Stop
9
000-255
Colour1
10
000-255
Colour2
11
000-255
Colour3
12
000-255
Colour4
13
000-255
Tilt2
14
000-255
Tilt1 Fine
15
Tilt2 Rotate
000-005
Stop
006-126
Movement forward fast -> slow
127-128
Stop
129-249
Movement forward Slow -> Fast
250-255
Stop
16
000-255
Colour5
17
000-255
Colour6
18
000-255
Colour7
19
000-255
Colour8
Colour table for Channel 9/10/11/12/16/17/18/19
Colour
000 - 007 Blackout

008 - 024 R
025 - 041 G
042 - 057 B
058 - 074 W
075 - 090 R + G
091 - 107 R + B
108 - 123 R + W
124 - 140 G + B
141 - 156 G + W
157 - 173 B + W
174 - 189 R + G + B
190 - 206 R + G + W
207 - 222 R + B + W
223 - 239 G + B + W
240 - 255 R + G + B + W
20 channel
Channel
Value
Function
1
000-255
Dimmer
2
000-007
Open
008-255
Strobe speed
3
000-007
No function
008-022
Movement01
023-037
Movement02
038-052
Movement03
053-067
Movement04
068-082
Movement05
083-097
Movement06
098-112
Movement07
113-127
Movement08
128-142
Movement09
143-157
Movement10
158-172
Movement11
173-187
Movement12
188-202
Movement13
203-217
Movement14
218-232
Movement15
233-247
Movement16
248-255
Sound active
4
000-255
Movement Speed
5
000-014
No Function
015-035
Colour Chase 1
036-056
Colour Chase 2
057-076
Colour Chase 3
078-097
Colour Chase 4
098-117
Colour Chase 5
118-138
Colour Chase 6
139-159
Colour Chase 7
160-179
Colour Chase 8
180-200
Colour Chase 9
201-220
Colour Chase 10
221-241
Colour Chase 11
242-255
Colour Chase 12
6
000-255
Chase Speed
7
000-255
Pan- Only when Chan 3 not used
8
000-255
Pan speed fast to slow
9
000-255
Tilt1
10
Tilt1 Rotate
000-005
Stop
006-126
Movement forward fast -> slow
127-128
Stop
129-249
Movement forward Slow -> Fast

250-255
Stop
11
000-255
Colour1 Only when Chan 5 not
used
12
000-255
Colour2 Only when Chan 5 not
used
13
000-255
Colour3 Only when Chan 5 not
used
14
000-255
Colour4 Only when Chan 5 not
used
15
000-255
Tilt2
16
Tilt2 Rotate
000-005
Stop
006-126
Movement forward fast -> slow
127-128
Stop
129-249
Movement forward Slow -> Fast
250-255
Stop
17
000-255
Colour5 Only when Chan 5 not
used
18
000-255
Colour6 Only when Chan 5 not
used
19
000-255
Colour7 Only when Chan 5 not
used
20
000-255
Colour8 Only when Chan 5 not
used
Colour table for Channel 11/12/13/14/17/18/19/20
Color
000 - 007 Blackout
008 - 024 R
025 - 041 G
042 - 057 B
058 - 074 W
075 - 090 R + G
091 - 107 R + B
108 - 123 R + W
124 - 140 G + B
141 - 156 G + W
157 - 173 B + W
174 - 189 R + G + B
190 - 206 R + G + W
207 - 222 R + B + W
223 - 239 G + B + W
240 - 255 R + G + B + W

4.4 Troubleshooting
Following are a few common problems that may occur during operation
and some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of the power and the main fuse.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX cables to see if linked correctly.
2. If the DMX address is showing but no response to the controller, check the
address settings and DMX polarity.
3. Try another DMX controller.
C. No response to the sound
1. Make sure the unit is not receiving a DMX signal.
2. Check the microphone to see if it is good by tapping it. The microphone is
located on the bottom plate of the unit.
5. Fixture Cleaning
The cleaning of external optical lenses must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which
the fixture operates: damp, smoky or particularly dirty surrounding can cause a
greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning fluid or mild soapy water.
!Always dry the parts carefully.
!Clean the external optics at least every 20 days.