ERGATTA Rower User manual

ASSEMBLY MANUAL
All manuals and user guides at all-guides.com

For step-by-step video instruction, watch the assembly video at
https://erga.io/rower-assembly
All manuals and user guides at all-guides.com

MAIN PARTS
OTHER PARTS
A
B
C
D
E
F
Rail x2*
Tablet
Rear Spacer* with Bungee
Seat
Footboard*
Tank Assembly & Mounting Arm
G
H
I
J
K
L
M
N
O
P
Q
R
S
Dolly Wheel Assembly x 2
JC Bolt × 8
JC Nut × 12
Handle Rest × 2
Handle Rest Bolt × 2
5mm Allen Key × 2
Footpads × 2
Syphon Pump × 1
Tablet Bolt x1
Power Cord x1
USB Cable x1
Pin Cable x1
Connector Cable x1
(4 are pre-installed on Rear Spacer)
A B
C
G H I
K L M
O P Q
J
N
R
D E F
S
All manuals and user guides at all-guides.com

1Lay the rails on the floor parallel to one another. Make sure that the
black extrusions are facing the inside of the rails.
All manuals and user guides at all-guides.com

2Position the rear spacer so that the logo is facing up and the bolt with
the bungee cord is facing down. Unscrew the JCN nuts from the rear
spacer.
JCN Nut
(x4)
All manuals and user guides at all-guides.com

3Connect the rear spacer to the rails.
All manuals and user guides at all-guides.com

4Screw the JCN nuts back into the side of the rails. Use the 5mm Allen
key to tighten.
JCN Nut
(x4)
Allen Keys
All manuals and user guides at all-guides.com

5Place the seat assembly between the rails. The indent on the seat
should face the rear spacer. Note: it may be necessary to separate
the rails slightly to fit.
All manuals and user guides at all-guides.com

6Unscrew the wheel assembly and attach the wheels to the outside of
the rails. Screw in the wheels using your hands, then use the 5mm
Allen key to tighten.
JCN Nut
(x2)
Wheel Assembly
(x2)
All manuals and user guides at all-guides.com

7Place the tank assembly between the rails. Using the JCN nuts and
JCB bolts, attach the tank to the rails. Use the 5mm Allen keys to
screw and tighten.
JCN Nut
(x4)
JCB Bolt
(x4)
Allen Keys
All manuals and user guides at all-guides.com

8Place the tank assembly between the rails. Using the JCN nuts and
JCB bolts, attach the tank to the rails. Use the 5mm Allen keys to
screw and tighten.
JCN Nut
(x4)
JCB Bolt
(x4)
Allen Keys
All manuals and user guides at all-guides.com

9Press and hold the heel adjustment button to add the footpads.
Footpads
(x2)
All manuals and user guides at all-guides.com

10 Screw the handle rests into position using the handle rest bolts. Do
not overtighten.
Handle Rest Bolt
(x2)
Handle Rests
(x2)
All manuals and user guides at all-guides.com

11 Stand the machine upright. Release the recoil belt and connect the
bunjee to the recoil strap.
All manuals and user guides at all-guides.com

12 Fill a separate tank with water. Using the siphon, fill the water tank
with water to the level 17 marker on the side of the tank. Add a
purification tablet (provided in your Ergatta bag).
All manuals and user guides at all-guides.com

13 Raise the mounting arm, gently pull the spring lock on the back of the
forward riser, and raise the arm until it locks in place.
All manuals and user guides at all-guides.com

14 Slide the tablet onto the end of the mounting arm (the speakers
should be on the top). Using the tablet bolt and 1/8" Allen key, secure
the tablet to the arm.
Tablet Bolt
All manuals and user guides at all-guides.com

15 Assemble the wires.
Side of MonitorBack of Monitor
Back
of Arm
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com