ErGear EGESD18B User manual

Electric Standing Desk
Instruction Manual
Technical Support:
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info: [e-mail]
Website: https://ergear.com
EGESD18B / EGESD18V / EGESD18N
Rev00(A)

Specifications
Tools Needed (Not lncluded)
Height Adjustment Range
28.3”–46.5” (72–118cm)
Desktop Dimensions
57.1” (145cm)
Power Input
100V–240V
Max. Speed
20mm/s
Operating Noise
<55dB
Max. Load
176 lbs / 80kg
RATED
Step 1
Supplied Parts
and Hardware
01 x 1
OR
Short Crossbar
02 x 1
Long Crossbar
03 x 1
Left Desk Leg
Right Desk Leg
04 x 1 05 x 1
Short Side Plate
06 x 1
Long Side Plate
07 x 1 08 x 1
Long Leg Base
09 x 1
Short Leg Base
Drill Phillips Screwdriver
Crossbar Connector
01

Bolt
M6 × 35mm
Ax 8
Bolt
M6 × 11mm
Bx 12 C1 x 1
Dx 16
Large Allen Wrench
3/16” (5mm)
Rubber Pad
10 x 1
Transmission Rod
C2 x 1
Step 4
Supplied Parts
and Hardware
13 x 1
Controller
Small Allen Wrench
5/64” (2mm)
14 x 2
Storage Hook
11 x 1
Gx 3Fx 8
Left Desktop Panel
Wood Dowel Pin
Screw
M5 × 16mm
Desktop Panel Connector
Ex 2
12 x 1
Right Desktop Panel
Fx 22
Screw
M5 × 16mm
15 x 2
Cable Clip
16 x 1
AC Adapter
Step 3
Supplied Parts
and Hardware
Step 2
Supplied Parts
and Hardware
02

Step 1 Assembling the Frame
02
01
01
Connect the crossbars together using the crossbar connector.
Connect the desk legs.
02
01
09
09
04
03
B
B
C1
C1
03

04
Attach the leg bases.
Attach the side plates.
Short
Side
Long
Side
07
03
04
06
A
08
08
04
C1
05
03
05
B
C1
04

Coupling nut
Before attaching the transmission rod, measure the heights of the two
desk legs to see if they are set at the same level. If not, insert the trans-
mission rod into the hole in the left leg. Turn the rod to adjust the left leg
so it's level with the right leg. Turn the rod clockwise to lower the left leg
or anti-clockwise to raise it.
Left Leg
a
b
b
Fig 1
Fig 2
a
Left Leg
10
Loosen the coupling nut.
10
03
10
10
Turn clockwise
Turn
anti-clockwise
Left Leg
05

Ensure the transmission rod is properly inserted into the hole in the left
leg. Smoothly connect the other end of the rod to the end of the motor
drive shaft on the right leg.
NOTE: Make sure the set
screw faces out.
Secure the transmission rod to the motor drive shaft by turning the set
screw clockwise.
10
C2
10
10
03
04
Right Leg
Right Leg
06

Tighten the coupling nut
to fine-tune transmission
rod fit.
D
07

Assemble the desktop.
Secure the desktop panels with the connectors.
Step 2 Assembling the Desktop
Drill
(not included)
Phillips
Screwdriver
(not included)
OR
You can use a drill (with
suitable torque and speed)
or a Phillips screwdriver.
12
11
12
11
12
11
G
12
11
F
E
OR
08

Step 3 Attaching the Desktop
Drill
(not included)
Phillips
Screwdriver
(not included)
OR
You can use a drill (with
suitable torque and speed)
or a Phillips screwdriver.
F
OR
Attach the desktop to the frame.
05
09

Drill
(not included)
Phillips
Screwdriver
(not included)
OR
You can use a drill (with
suitable torque and speed)
or a Phillips screwdriver.
13
14
F
F
OR
OR
Attach the controller and hooks to the desktop.
10

Step 4 Connecting the Cables
13
16
13
16
15
11

Using the Controller
Select Height Setting 1
Press the button, and the desk will move to the height that was
previously set for that button.
Select Height Setting 2
Press the button, and the desk will move to the height that was
previously set for that button.
Select Height Setting 3
Press the button, and the desk will move to the height that was
previously set for that button.
Raise the Desk
Press the button to raise the desk continuously until it reaches the
highest position of 46.5” (118cm) or the button is released.
Lower the Desk
Press the button to lower the desk continuously until it reaches the
lowest position of 28.3” (72cm) or the button is released.
Save Current Height Setting
Short-press the button, and the display will flash. Press the , , or
button to save the current height setting to that button.
12

Settings
Change Display
Height Units
Change Collision
Detection Sensitivity
Reset
Press and hold the button for 5 seconds, and the screen
will show ‘RES.’ Continue holding until the desk goes down to
its lowest level and comes back up slightly.
Protection Mode Error Codes
Hot
E10
E20
E02
Overheating Protection: When the motor has been working
continuously for 2 minutes, it will stop operating to prevent
damage from overheating. Wait for at least 18 minutes
before making any further height adjustment.
Sensor Malfunction Warning: Motor safety sensor can’t be
detected. Power off, check the connection between the
motor and controller, and power back on again.
Overloading Warning: Max load exceeded. If raising the
desk, take the things off the desk and try again. If lowering
the desk, power off, take the things off the desk, power
back on, and try again.
Operation Status Warning: The desk stops moving if
vibration, impact, or incline are detected. If this detection
is incorrect, follow the reset instructions before continuing
use.
Press and hold the button until a flashing ‘S-’ is displayed.
Press again, and ‘Un’ is displayed. Press to select it,
press or to switch between ‘IN’ (imperial) and ‘SI’
(metric), and press to save your choice.
Long press the button, ‘S-‘ shows and flashes. Press
again and the display shows ‘Un‘. Press or to switch to
‘CF‘. Press to select. Press or to switch between ‘OFF‘,
Low (L), Normal (n) or Heavy (H) collision force detection.
Press to save your choice.
13

E32
E31
E60
–
Overvoltage Protection: Input voltage too high. If the correct
AC adapter is being used, power off the desk, check the
connection between power and the controller, and power
on again.
Undervoltage Protection: Input voltage too low. If the correct
AC adapter is being used, power off the desk, check the
connection between power and the controller, and power
on again.
Unequal Leg Height Warning: Power off the desk and
check whether the left and right legs are at the same
height. Adjust if necessary by following the instructions.
Power on again.
Cable Disconnection Warning: Check motor and controller
cable connections. Normal operation should return once
all connectors are properly connected.
14

Thank you for choosing this product. We strive to provide you with the
best quality products and service in the industry. Should you have
any issues, please don't hesitate to contact us.
Technical Support
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info
[email protected]
Website
https://ergear.com
860-00890-00 Rev00