BullFrog 0319 TAO User guide

Optionally Turnable up to 360° Practical stool or armrest cushion Optionally functional bracket
with practical back cushion
ASSEMBLY AND INSTRUCTION MANUAL
www.bullfrog-design.com
MODEL 0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

1. Place the enclosed parts in front of you.
2. Position the elements at the place supposed to stay and place the upholstery upside
down on the floor. To avoid damages at the furniture or at the floor use a suitable
support.
3. Screw in the enclosed grub screws (a) into the 4 threads (d).
a
d d
d d
a
a a
ATTENTION! To ensure secure assembly, please observe the individual steps of instruction!
It is necessary that the furniture always be mounted in pairs (2 persons)!
Assembly of type 23T:
4 x grub screw (a)
4 x washer (b)
4 x nut (c)
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

a
e
ee
e
a
aa
4. Apply the plateau with its 4 bores (e) onto the 4 grub screws (a).
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

5. Plug washers (b) onto grub screws (a) and tightem them with a nut (c).
Seat cushion
Plateau
Grub screw
Washer
Nut
c
b
a
6. Mount the connectors! See: “mounting of connectors”!
7. Tilt mounted sofa forward onto its feet.
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

1. Unscrew bolt with enclosed allen key from cone and place bolt, large washer and
small washer in front of you.
2. Position the elements at the place supposed to stay and place the upholstery upside
down on the floor. To avoid damages at the furniture or at the floor use a suitable
support.
3. Li plateau above the seat cushion.
Assembly of type 23TF:
ATTENTION! To ensure secure assembly, please observe the individual steps of instruction!
It is necessary that the furniture always be mounted in pairs (2 persons)!
1 x bolt
1 x washer,
large
1 x washer,
small
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

4. Position the bearing bush (a) of plateau above cone (b) of seat cushion.
b
a
5. Plug bearing bush (a) of plateau onto cone (b) of seat cushion.
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

8. Aer assembly of connectors: tilt mounted sofa forward onto its feet. Pay
attention to plateau and seat cushion, it may move unintentional due to rotary and
sliding system.
7. Mount the connectors! See: “mounting of connectors”!
Inside:
plug onto
cone
Outside:
closed surface
6.
1) Place the large washer onto cone.
2) Place the small washer on large washer and tighten it with enclosed screw.
Turning heaviness is adjustable by contact pressure of screw.
Information
Information
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

Mounting of connectors:
Possible connector points:
23T
23TF
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

Mounting of connectors:
B
2
2
1
1
A
Connector
1
1
2
2
Connector
Hand screw
Hand screw
1. Screw connectors (1) of element (A) with the hand screws (2) into threaded sockets and
tighten hand screws (2).
Place the enclosed parts in front of you.
2
1
1
29TF
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R

B
2
2
2
2
B
A
A
2. Screw hand screws (2) slightly into element (B), so that hand screws do not drop of.
3. Firmly push together (A) and (B) so the threaded bar of hand screw (2) will slide into the
slot of connector (1) of element (B).
1
2
Connector
Hand screw
4. Tighten hand screws (2).
0319 TAO
© 2019 K URT BEI E R &KATI QU I N G E R