ErGear EGESD5B-4 User manual

48” Electric Standing Desk
Instruction Manual
Technical Support:
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info: [e-mail]
Website: https://ergear.com
EGESD5B-4 / EGESD5V-4
Rev03(A)

Bolt
M6 x 35mm
Ax 4
Transmission Rod
Specifications
Height Adjustment Range
28.3”–46.5” (72-118cm)
Power Input
100V-240V Max. Speed 20mm/s Operating Noise <55dB Max. Load 176 lbs / 80 kg
RATED
Step 1
Supplied Parts
and Hardware
Crossbar Left Desk Leg Right Desk Leg
Bolt
M6 x 11mm
Large Allen Wrench
3/16” (5mm)
Step 2
Supplied Parts
and Hardware
Side Plate Bolt
M6 x 11mm
Leg Base
01 x 1 02 x 1 03 x 1
04 x 2
Cx 1
Bx 8
05 x 2 06 x 1 Ax 4
Tools Needed (Not lncluded)
Drill Phillips Screwdriver
OR
01

Step 3
Supplied Parts
and Hardware
Desktop
07 x 1
Wood Dowel Pin
Gx 4
Desktop Panel Connector
Hx 2
Storage Hook
Ix 2
Screw
M5 X 16mm
Fx 20
Screw
M5 X 16mm
Fx 6
Step 5
Supplied Parts
and Hardware
AC Adapter
14 x 1
Cable Clip
Kx 2
Controller
08 x 1
Step 4
Supplied Parts
and Hardware
Wrist Rest
11 x 1
Keyboard Stopper
10 x 1
Keyboard Tray
09 x 1
Screw
M4 X 6mm
Jx 3
Small Allen Wrench
5/64” (2mm)
Dx 1
Rubber PadLarge Allen Wrench
3/16” (5mm)
Cx 1 Ex 10
Right Keyboard Tray
Side Plate
13 x 1
Left Keyboard Tray
Side Plate
12 x 1
02

Step 1 Assembling and Connecting
the Desk Legs
HEAVY! You may
need assistance
with this step.
Large
Allen Wrench
Large
Allen Wrench
B
02
03
01
03
04
C
01
C
04
04
A
03

Step 2 Attaching the Side Plates and the
Transmission Rod
Large
Allen Wrench
C
Loosen the coupling nut.
Coupling nut
A
05
05
05
06
04

06
Right Leg
Ensure the transmission rod is properly inserted into the hole in the
left leg. Smoothly connect the other end of the rod to the end of
the motor drive shaft on the right leg.
Before attaching the transmission rod,
measure the heights of the two desk legs to see
if they are set at the same level. If not, insert the
transmission rod into the hole in the left leg.
Turn the rod to adjust the left leg so it's level
with the right leg. Turn the rod clockwise to
lower the left leg or anti-clockwise to raise it.
Left Leg
Turn
anti-clockwise
b
a
Fig 1
Turn clockwise
b
a
Left Leg
Fig 2
NOTE: Make sure the set
screw faces out.
05

Secure the transmission rod to the motor drive shaft by turning the set
screw clockwise.
Tighten the coupling nut
to fine-tune transmission
rod fit.
DSmall
Allen Wrench
Small
Allen Wrench
E
06

Assemble the desktop.
Step 3 Assembling and Attaching the Desktop
07
07
H
F
Drill
(not included)
Phillips
Screwdriver
(not included)
OR
OR
You can use a drill (with
suitable torque and speed)
or a Phillips screwdriver.
07
07
G
07

F
Attach the desktop to the frame.
Attach the controller and hooks to the desktop.
F
I
b
OR
F
08
a
OR
OR
08

J
10
09
11
11
09
Attach the stopper to the keyboard tray.
Attach the wrist rest to the keyboard tray.
Drill
(not included)
Phillips
Screwdriver
(not included)
OR
OR
You can use a drill (with
suitable torque and speed)
or a Phillips screwdriver.
Step 4 Assembling and Attaching the
Keyboard Tray
09

F
13
FF
NOTE: Note the position of
the stopper on the keyboard
tray in this step.
Phillips Screwdriver
(not included)
Attach the assembled keyboard tray to the desk.
You can use a Phillips screwdriver instead of a drill for
easier access to screw in the screws.
Pull out the inner parts of the drawer slides a little for easier keyboard
tray alignment. Then align and insert the tray.
12
13
10

Step 5 Connecting the Cables
14
K
08
08
14
11

Using the Controller
Select Height Setting 1
Press the button, and the desk will move to the height that was
previously set for that button.
Select Height Setting 2
Press the button, and the desk will move to the height that was
previously set for that button.
Select Height Setting 3
Press the button, and the desk will move to the height that was
previously set for that button.
Raise the Desk
Press the button to raise the desk continuously until it reaches the
highest position of 46.5” (118cm) or the button is released.
Lower the Desk
Press the button to lower the desk continuously until it reaches the
lowest position of 28.3” (72cm) or the button is released.
Save Current Height Setting
Short-press the button, and the display will flash. Press the , , or
button to save the current height setting to that button.
12

Settings
Change Display
Height Units
Change Collision
Force Detection
Reset
Press and hold the button for 5 seconds, and the screen
will show ‘RES.’ Continue holding until the desk goes down to
its lowest level and comes back up slightly.
Protection Mode Error Codes
Hot
E10
E20
E02
Overheating Protection: When the motor has been working
continuously for 2 minutes, it will stop operating to prevent
damage from overheating. Wait for at least 18 minutes
before making any further height adjustment.
Sensor Malfunction Warning: Motor safety sensor can’t be
detected. Power off, check the connection between the
motor and controller, and power back on again.
Overloading Warning: Max load exceeded. If raising the
desk, take the things off the desk and try again. If lowering
the desk, power off, take the things off the desk, power
back on, and try again.
Operation Status Warning: The desk stops moving if
vibration, impact, or incline are detected. If this detection
is incorrect, follow the reset instructions before continuing
use.
Press and hold the button until a flashing ‘S-’ is displayed.
Press again, and ‘Un’ is displayed. Press to select it,
press or to switch between ‘IN’ (imperial) and ‘SI’
(metric), and press to save your choice.
Long press the button, ‘S-‘ shows and flashes. Press
again and the display shows ‘Un‘. Press or to switch to
‘CF‘. Press to select. Press or to switch between ‘OFF‘,
Low (L), Normal (n) or Heavy (H) collision force detection.
Press to save your choice.
13

E32
E31
E60
–
Overvoltage Protection: Input voltage too high. If the correct
AC adapter is being used, power off the desk, check the
connection between power and the controller, and power
on again.
Undervoltage Protection: Input voltage too low. If the correct
AC adapter is being used, power off the desk, check the
connection between power and the controller, and power
on again.
Unequal Leg Height Warning: Power off the desk and
check whether the left and right legs are at the same
height. Adjust if necessary by following the instructions.
Power on again.
Cable Disconnection Warning: Check motor and controller
cable connections. Normal operation should return once
all connectors are properly connected.
14

Thank you for choosing this product. We strive to provide you with the
best quality products and service in the industry. Should you have
any issues, please don't hesitate to contact us.
Technical Support
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info
[email protected]
Website
https://ergear.com
860-00405-02 Rev03