Ergotron 45-295 User manual

RI
*UHY(ವ
/;/&'$FFHVVRU\$UP
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
(QJOLVK(VSD³RO)UDQ©DLV'HXWVFK1HGHUODQGV,WDOLDQR6YHQVND㡴㦻崭㻘幼
,QFOXGHV
&RQVWDQW)RUFHറ
7HFKQRORJ\
CAUTION! The LX Arm Accessory is designed to be used with the
45-295 LX Desk Mount LCD Arm, Tall Pole and the 45-509 LX Dual
Stacking Arm, Tall pole products. Using the LX Arm Accessory with
any other product may create an unstable situation resulting in
equipment damage and/or personal injury.
8VHUV*XLGH
(QJOLVK
)RUWKHODWHVW8VHU,QVWDOODWLRQ*XLGHSOHDVHYLVLWZZZHUJRWURQFRP

RI
*UHY(ವ
7 - 20 lbs
(3.2 - 9.1 kg)
5°
70°
360°
360°
180°
13 "
( 330 mm)
360°
3x
4x
4x
13.7" (348 mm)
3x
20.7" (525 mm)
Features & Specifications
Can have up to 4 arms on a pole when used with the 45-509
LX Dual Stacking Arm, Tall pole
See updated maximum weight capacities:
11 lbs (5 kg)
per monitor
Max Monitor Width:
11 lbs (5 kg)
per monitor
11 lbs (5 kg)
per monitor
11 lbs (5 kg)
per monitor
Max Monitor Width:
Maximum monitor width will decrease depending
on arm conguration.
Maximum monitor width will decrease depending
on arm conguration.

RI
*UHY(ವ
AB CD
1
2
3
4
M4 x 10mm
4x
M4 x 10mm
4x
4mm
1x
1x
1x
M3 x 6mm
1x 1x
2x
2.5mm 1x
1x
1x
1x 4x
10 - 24 x 1/2”
1/8”
Tools Needed
Components

RI
*UHY(ವ
1M4 x 10mm
M4 x 10mm
4x
4x
0°
M3 x 6mm
1x
:$51,1* 6WRUHG(QHUJ\+D]DUG7KH5LVHUPHFKDQLVPLVXQGHUWHQVLRQDQGZLOOPRYHXSUDSLGO\RQLWVRZQDVVRRQDVDWWDFKHGHTXLSPHQWLVUHPRYHG
)RUWKLVUHDVRQ'2127UHPRYHHTXLSPHQWXQOHVVWKH5LVHUKDVEHHQPRYHGWRWKHKLJKHVWSRVLWLRQ)DLOXUHWRIROORZWKLVLQVWUXFWLRQPD\UHVXOWLQVHULRXV
SHUVRQDOLQMXU\DQGRUHTXLSPHQWGDPDJH

RI
*UHY(ವ
22.5mm
CAUTION! The LX Arm Accessory is designed to be used only
with the 45-295 LX Desk Mount LCD Arm, Tall Pole product, with
a total of two (2) arms per pole. Using the LX Arm Accessory with
any other product or in quantities greater than two (2) arms per
pole may create an unstable situation resulting in equipment
damage and/or personal injury.

RI
*UHY(ವ
32.5mm

RI
*UHY(ವ
4
NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow the cable routing
instructions in this manual. Failure to follow these instructions may result in equipment
damage or personal injury.

RI
*UHY(ವ
5
4mm
a
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or difficult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
Lift – Up and down

RI
*UHY(ವ
4mm
b
0°
M3 x 6mm
c
d
2.5mm
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too difficult to move,
then you'll need to decrease friction:
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too difficult to move,
then you'll need to decrease friction:
CAUTION: DO NOT remove screw. Removing screw may cause damage to
equipment.
Tilt – Forward and Backward
Arm Swing – Side-to-side
Rotate – Portrait/Landscape

RI
*UHY(ವ
k(UJRWURQ,QF$OOULJKWVUHVHUYHG
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
/HDUQPRUHDERXWHUJRQRPLFFRPSXWHUXVHDWZZZHUJRWURQFRPHUJRQRPLFV
)RUORFDOFXVWRPHUFDUHSKRQHQXPEHUVYLVLWKWWSFRQWDFWHUJRWURQFRP
)RU6HUYLFHYLVLWZZZHUJRWURQFRP
)RU:DUUDQW\YLVLWZZZHUJRWURQFRPZDUUDQW\