Ergotron WorkFit LX User manual

1 of 19
888-45-323-G-00 rev.C • 12/18
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
WorkFit LX
Sit Stand Desk Mount System
™
< 25 lbs
(11.3 kg)
0-5 lbs
(0-2.3 kg)
0.78”-2.25” (20-57mm)
0.5"-2.5" (13-64mm)
0.78"-2.56"
(20-65mm)
CLAMP GROMMET HOLE
User's Guide
English
For the latest User Installation Guide please visit: www.ergotron.com
Maximum Screen
Size* = 42”
*Limited to 25 lbs
maximum

2 of 19
888-45-323-G-00 rev.C • 12/18
180°
360°
180°
90°
5°
20"
(508 mm)
3°3°
5°
70°
360°
360°
180°
20"
(508 mm)
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the
full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in
desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your
product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed
from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps
to ensure safe and optimum operation.
CAUTION: DO NOT rotate monitor past rear
edge of desk. Doing so will create an unstable
situation and may cause equipment damage or
personal injury.
CAUTION: Monitor may
hit Keyboard arm in some
congurations. Use caution
when moving your monitor
and keyboard arms.
Features & Specifications

3 of 19
888-45-323-G-00 rev.C • 12/18
AB CD
1
2
3
4
5
6
2x
1x
4x
1x 1/4”
8mm
1x
1x
2x
2x
2x
2x
M6
M6 x 45mm
2x 4x
1x
1x 1x
1x
4x
M4 x 10mm
4x
M4 x 8mm
4x
M4 x 10mm
4x
M3 x 6mm
1x
2.5mm
1x
M4 x 14mm
2x
4x M4 x 12mm
4x M5 x 12mm
4x M6 x 12mm
4x
4x
M5 x 7mm
4x
4x
M5 x 20mm
1x 4mm
1x 5mm
6x
1x
1x
1x 1x
1x
1/4"
Components
M8M5 Converter
Tools Needed

4 of 19
888-45-323-G-00 rev.C • 12/18
1
13.3"
(338 mm)
13.3"
(338 mm)
5.9"
(150 mm)
5.9"
(150 mm)
5.9"
(150 mm)
5.9"
(150 mm)
19.2"
(488 mm)
19.2"
(488 mm)
10.75"
(273 mm) 10.75”
(273 mm)
10.3"
(262 mm)
10.3"
(262 mm)
10.3"
(262 mm)
10.3"
(262 mm)
11.7"
(297 mm)
17.6"
(447 mm)
17.6"
(447 mm)
22"
(559 mm)
23.6"
(599 mm)
3.7"
(93 mm)
3.7"
(93 mm)
18.3"
(466 mm) 18.3"
(466 mm)
11.7"
(297 mm)
1.75"
(44 mm)
11.5"
(292 mm)
Desk Placement
Maximum dimensions to
allow keyboard arm to
lower below front of desk.
CLAMP GROMMET HOLE
Grommet hole can be located anywhere along this arch.
CAUTION: Base must be completely on desk surface.
Failure to follow these instructions may result in
equipment damage or personal injury.
Top View Top View
Example of one conguration
Corner mount - Top ViewCorner mount - Top View
Front of Desk
Front of Desk
Front of Desk
Front of Desk
Side View Side View
Front of Desk
Front of Desk

5 of 19
888-45-323-G-00 rev.C • 12/18
0.78"-1.38" (20-35mm) 1.18"-2.56" (30-65mm)
1/4"
1/4”
8mm
1x
1x
1x
1x
c
d
a
b
2
4mm
4mm
4mm
4mm
CAUTION: Bolt must be
centered in hole.
CLAMP GROMMET HOLE
DESK THICKNESS

6 of 19
888-45-323-G-00 rev.C • 12/18
3
4
d
abc
a
ef
1x
2x
M6
M6 x 45mm
4mm
4x
2.5mm
Mount extension and arm to pole.

7 of 19
888-45-323-G-00 rev.C • 12/18
c
d
4x
b
5a
b
c
M4 x 8mm
4x

8 of 19
888-45-323-G-00 rev.C • 12/18
0˚
6
iii
M3 x 6mm
1x
Portrait / Landscape Options
OPTION i If you want full portrait/landscape rotation, skip to step 8 on the next page.
OPTION ii If you do not want your TV/Monitor to rotate all all, you can stop rotation by inseting
the set screw.

9 of 19
888-45-323-G-00 rev.C • 12/18
7
A
B
C
D
75x75mm
100x100mm
100x200mm
200x200mm
200x100mm
100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
200mm (7-7/8”)
100mm (3-15/16”)
200mm (7-7/8”)
11
10
11
11
VESA Adapter
Congurations
TV/Monitor Hole
Pattern Sizes
Check size of
TV/Monitor hole
pattern

10 of 19
888-45-323-G-00 rev.C • 12/18
OR
A
75x75mm
100x100mm 100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
75mm (2-15/16”)
7
813
M4 x 10mm
M4 x 10mm
4x
M4 x 10mm
4x
Mount Type A TV/Monitor to Arm

11 of 19
888-45-323-G-00 rev.C • 12/18
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
200mm (7-7/8”)
100mm (3-15/16”)
200mm (7-7/8”)
BCD
7a
100x200mm 200x200mm 200x100mm
4x
M5 x 7mm
12
7b
4x4x 4x
M4 x 12mm M5 x 12mm M6 x 12mm
Mount VESA Adapters to Arm based on TV/Monitor hole
pattern size (B, C, or D) .
Mount Type B, C, or D TV/Monitor to Arm
NOTE: To reduce M8
holes for use with M5
screws, or if you have a
model with Samsung
holder rings, follow the
M8M5 KIT instructions
on the next page.

12 of 19
888-45-323-G-00 rev.C • 12/18
4x
4x
4x
4x
M5 x 20mm
M5 x 20mm
M8M5 KIT Instructions
NOTE: Follow this step only if your TV/monitor has M8 holes which need to be
reduced to M5.
NOTE: Follow this step only for Samsung models using the holder ring.
Install M8M5 reducer bushing to TV/Monitor and use M5 x 20 mm monitor
screws to secure.
Install M8M5 reducer bushing to TV/Monitor then use M5 x 20 mm monitor screws
and Samsung holder ring to secure.
TV/Monitor Mounting
M8 size hole
TV/Monitor Mounting
M8 size hole
Holder Ring
(Not included *Samsung Only)

13 of 19
888-45-323-G-00 rev.C • 12/18
8
cd
ef
1x
1x 1x
2x
4mm
4mm
M6
M6 x 45mm
2.5mm
b
1x
a
Part contains grease. Use bag to p
r
hands from getting greasy.
Mount extension and arm to pole.

14 of 19
888-45-323-G-00 rev.C • 12/18
9Organize and route cables
Leave enough slack in cables
to allow full range of motion.

15 of 19
888-45-323-G-00 rev.C • 12/18
WARNING WARNING
10
5mm
5mm
Adjustment Step
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or difficult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
To adjust the arm lift:

16 of 19
888-45-323-G-00 rev.C • 12/18
4mm
11
4mm
CAUTION: DO NOT remove screw. Removing
screw may cause damage to equipment.
To adjust the TV/monitor tilt:
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:

17 of 19
888-45-323-G-00 rev.C • 12/18
12
13
2.5mm
WARNING
5mm
5mm
To adjust height on pole:
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
Lift – Up and down
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:

18 of 19
888-45-323-G-00 rev.C • 12/18
3°3°
M4 x 14mm
2x
How to remove this tilting feature:
Save these screws incase you want to add
this feature later.

19 of 19
888-45-323-G-00 rev.C • 12/18
© 2015 Ergotron, Inc. All rights reserved. WorkFit™ is a registered trademark of Ergotron, Inc.
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
NOTE: When contacting customer service, reference the serial number.
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty