Ergotron LX Desk Mount LCD Arm User manual

1 of 12
888-45-047-W-05 rev.U • 12/18
LX Wall Mount Keyboard Arm
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
English
For the latest User Installation Guide please visit: www.ergotron.com

2 of 12
888-45-047-W-05 rev.U • 12/18
AB CD
1
2
3
4
0 - 5 lbs
(0 - 2.3 kg)
4mm
1x
180° 360°
180°
13" (330 mm)
1x
1x
1x
1x 1/8"
4x
10-24 x 1/2"
2
1
1x 2.5mm
M8 x 80mm
2x
2x
1x
1x
4x
1x
13mm
7mm
4x
M4 x 8mm
1x
1x
1x
1x 1x
90°
5°
3°3°
2x
2x
M4 x 14mm
Ø 3/8” (10mm)
Ø 3/16" (5mm)
Tools Needed
Components
Concrete Wall Mounting
Wood Stud Mounting
Stud Finder

3 of 12
888-45-047-W-05 rev.U • 12/18
1
5’0” - 6’4”
(152-185cm)
22.5”
(571mm)
31.5”
(800mm)
35.4”
(899mm)
5’0” - 6’4”
(152-185cm)
26.4”
(670mm)
14.8”
(377mm)
2.5”
(63mm)
17.7”
(449mm) 20.7”
(526mm)
0.6”
(14mm)
1.8”
(46mm)
8.3”
(211mm)
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5'0"-6'4"
(152-185cm) when set up for standing .
If user heights are dierent than this, you should change mounting height to accommodate user heights. (Change mount-
ing height one inch for every one inch dierence in user heights).
Mounting Height for Ergonomic Workstation
Determine mounting location:
Top view showing range of motion when pulled out from the wall.
Front view with arm pushed back against the wall.

4 of 12
888-45-047-W-05 rev.U • 12/18
4x
10-24 x 1/2"
1/8"
2
5 6 7
4.1"
(104mm)
1.125"
(28.6mm)
6"
(152mm)
33" (838 mm)
To Floor
CAUTION: Make sure the wall mount bracket is level,
ush and snug to the wall surface. DO NOT OVERTIGHT-
EN THE BOLTS.
WARNING: Ensure that the wall structure is capable
of supporting four times the total weight of mounted
equipment. Mounting to wall surfaces that do not meet
this criteria may result in an unstable, unsafe condition
which could lead to personal injury and/or property
damage. Consult a construction professional if you
have any doubt about what this means in regard to
your particular application.
Concrete Ergotron product Wood
Optional locking feature
(customer supplied lock)

5 of 12
888-45-047-W-05 rev.U • 12/18
1/8"
1/8"
1/8"
1/8"
4x
10-24 x 1/2"
4x
10-24 x 1/2"
8
8
8
8
4x
10-24 x 5/8"
Ergotron product
NOTE: Fasteners may unwind due to vibration caused by move-
ment of mounting solution over time. Inspect mounting solution
for loose fasteners on a routine basis. If desired, apply a light duty
thread locking adhesive to fasteners before installation to prevent
back-out.
When attaching to Pole Clamps, use 10-24 x 5/8”
screws included with pole brackets, Do NOT use
10-24 x 1/2” screws
NOTE: Wall Track and Brackets sold separately.

6 of 12
888-45-047-W-05 rev.U • 12/18
bacd
e
13 mm
M8 x 80mm
2x
Ø 3/16"
(5 mm)
8
Wood Stud Mounting
Stud Finder

7 of 12
888-45-047-W-05 rev.U • 12/18
13 mm
M8 x 80mm
2x
3-1/8"
(80 mm)
Ø 3/8"
(10 mm)
1
2
2x
ba
cde
8
Concrete Wall Mounting
WARNING:
Mounting holes must be at least 3-1/8” (80mm) deep and must be located within solid concrete, not mortar or covering material.
If you drill into an area of concrete that is not solid, reposition mounting holes until both anchors can be fully inserted into solid
concrete!
WARNING:
Anchors that are not fully set in solid concrete will not support the applied load resulting in an unstable, unsafe condition which
could lead to personal injury and/or property damage. Consult a construction professional if you have any doubt about what this
means in regard to your particular situation.

8 of 12
888-45-047-W-05 rev.U • 12/18
4x
4
WARNING
3ab
M4 x 8mm
1x
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!

9 of 12
888-45-047-W-05 rev.U • 12/18
6
5abc
d
ghi
ef
CABLE ROUTING
Leave Slack in cable

10 of 12
888-45-047-W-05 rev.U • 12/18
7
4mm
a
b
2.5mm
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or difficult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
Lift – Up and down
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Arm Swing – Side-to-side
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
If this product is too difficult to move,
then you'll need to decrease friction: