Ergotron WORKFIT User manual

888-97-374-G-01 rev.K • 04/19
1 of 8
Dual Monitor Kit
for WorkFit-T, TL, TLE, TX, and Corner Desk Converters
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Türkçe, 日本語, 汉语
User's Guide
English
For the latest User Installation Guide please visit: www.ergotron.com

888-97-374-G-01 rev.K • 04/19
2 of 8
6 - 14 lbs
(2.72-6.35 kg)
6 - 14 lbs
(2.72-6.35 kg)
< 5 lbs
(2.25 kg)
A
B
C
D
5"
(127 mm)
A+B+C+D< WorkFit-T: 25.3 lbs (11.48 kg)
WorkFit-TL: 30.3 lbs (13.74 kg)
WorkFit-TLE: 30.3 lbs (13.74 kg)
WorkFit-TX: 30.3 lbs (13.74 kg)
WorkFit-Corner: 25.3 lbs (11.48 kg)
WARNING
Impact Hazard!
Moving Parts can Crush and Cut.
Raise monitor to top of vertical adjustment
BEFORE removing.
Failure to heed this warning may result in serious
personal injury or property damage!
822-635
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your
equipment is properly installed on the product before attempting adjustments. This product should move
smoothly and easily through the full range of motion and stay where you set it. If movements are too
easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to
create smooth and easy movements. Depending on your product and the adjustment, it may take many
turns to notice a diff erence. Any time equipment is added or removed from this product, resulting in a
change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and
optimum operation.
Warning: Impact Hazard! Moving Parts can Crush and Cut.
Raise worksurface to top of vertical adjustment BEFORE removing equipment.
Failure to heed this warning may result in serious personal injury and or property damage!
Warning: Impact Hazard! Moving Parts can Crush and Cut.
Raise monitor to top of vertical adjustment before removing.

888-97-374-G-01 rev.K • 04/19
3 of 8
AB CDE
1
2
3
4
1x
8x
2x M4 x 5mm
4x M6 x 6mm
1x
1x 4mm
1x
M4 x 10mm
8x
M4 x 10mm
8x
2x
M4 x 10mm
2x 2x
M4 x 8mm
2x 4x
4x
M6 x 25mm
4x
M6 x 20mm

888-97-374-G-01 rev.K • 04/19
4 of 8
1a
c
c
b4x
4x
M6 x 25mm
4mm
b4x
M6 x 20mm
4mm
4x
4x
M6 x 20mm
4mm
cb
WorkFit -T, TL, TLE
WorkFit -T Corner
WorkFit - TX

888-97-374-G-01 rev.K • 04/19
5 of 8
24mm
4x
M6 x 6mm
4
3
M4 x 10mm
M4 x 10mm
8x
8x
1.5˚ 6.5˚
0°
M4 x 8mm
2x

888-97-374-G-01 rev.K • 04/19
6 of 8
5
2x
1x
M4 x 5mm
M4 x 5mm
M4 x 10mm
1x
6
7
8x
1x
2x
Center total width of mounted equipment on stand.
NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual.
Failure to follow these instructions may result in equipment damage or personal injury.

888-97-374-G-01 rev.K • 04/19
7 of 8
8
a4mm
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a diff erence. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:

888-97-374-G-01 rev.K • 04/19
8 of 8
© 2014 Ergotron, Inc. All rights reserved.
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
Ready to get moving on an active workstyle? Check out www.ergotron.com/tips to get started.
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty