ESAB Origo Mig C170 3ph User manual

GB
Valid for serial no. 626-xxx-xxxx0463 344 001 GB 20120612
Origo™
Mig C170 3ph
Mig C200 3ph
Mig C250 3ph
Instruction manual

- 2 -

- 3 -
TOCe
Rights reserved to alter specifications without notice.
1 SAFETY 4...........................................................
2 INTRODUCTION 6...................................................
2.1 Equipment 6................................................................
3 TECHNICAL DATA 6.................................................
4 INSTALLATION 7....................................................
4.1 Location 7..................................................................
4.2 Assembly of components 8...................................................
4.3 Electrical installation 8.......................................................
4.4 Mains power supply 9........................................................
5 OPERATION 9.......................................................
5.1 Connection and control devices 10.............................................
5.2 Welding without gas 11.......................................................
5.3 Wire feed pressure 11........................................................
5.4 Replacing and inserting wire 11................................................
5.5 Overheating protection 12.....................................................
6 MAINTENANCE 12....................................................
6.1 Inspection and cleaning 12....................................................
7 FAULT TRACING 13..................................................
8 ORDERING OF SPARE PARTS 13......................................
DIAGRAM 14............................................................
ORDER NUMBER 18.....................................................
WEAR PARTS 19........................................................
ACCESSORIES 20.......................................................

- 4 -
ba46e
1 SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in
jury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
Sits operation
Slocation of emergency stops
Sits function
Srelevant safety precautions
Swelding and cutting
2. The operator must ensure that:
Sno unauthorised person is stationed within the working area of the equipment when it is
started up.
Sno-one is unprotected when the arc is struck
3. The workplace must:
Sbe suitable for the purpose
Sbe free from drafts
4. Personal safety equipment
SAlways wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves.
SDo not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions
SMake sure the return cable is connected securely.
SWork on high voltage equipment may only be carried out by a qualified electrician.
SAppropriate fire extinquishing equipment must be clearly marked and close at hand.
SLubrication and maintenance must not be carried out on the equipment during operation.
WARNING
Do not use the power source for thawing frozen pipes.
GB

- 5 -
ba46e
WARNING
Read and understand the instruction manual before installing or operating.
Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
SInstall and earth the unit in accordance with applicable standards.
SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
SInsulate yourself from earth and the workpiece.
SEnsure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
SKeep your head out of the fumes.
SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
SProtect bystanders with suitable screens or curtains.
FIRE HAZARD
SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
SProtect your ears. Use earmuffs or other hearing protection.
SWarn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION
Read and understand the instruction manual before
installing or operating.
CAUTION
This product is solely intended for arc welding.
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
GB

- 6 -
ba46e
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2 INTRODUCTION
Mig C170 3ph, Mig C200 3ph and Mig C250 3ph are step controlled power
sources of a compact design, intended for welding with solid steel, stainless steel or
aluminium wire as well as tubular wire with or without shielding gas. It is possible to
weld with homogeneous wire/shielding gas and weld with gasless tubular wire by
switching the + and - connections on the switching terminal by the wire feed unit.
ESAB's accessories for the product can be found on page 20.
2.1 Equipment
The power source is supplied with:
SWelding gun
SReturn cable with return clamp
SShelf for gas cylinder
SInstruction manual
3 TECHNICAL DATA
Mig C170 3ph Mig C200 3ph Mig C250 3ph
Voltage 400-415V,
3∼50/60 Hz
400-415V,
3∼50/60 Hz
230/400-415V,
3∼50/60 Hz
Permissible load at
100% duty cycle 100A 120A 150A
60 % duty cycle 130A 150A 190A
35 % duty cycle 170A 200A 250A
Setting range (DC) 30-170A 30-200A 40-280A
Open circuit voltage 15.5-30.6V 16.0-31.8V 15.0-37.0V
Open circuit power 310W 210W 340W
Power factor at max load 0.97 0.97 0.97
Control voltage 42V, 50/60Hz 42V, 50/60Hz 42V, 50/60Hz
Wire feed speed 1.0-17m/min 1.0-17m/min 1.0-17m/min
Burnback time 0.02-0.25s 0.02-0.25s 0.02-0.25s
GB

- 7 -
ba46e
Mig C250 3phMig C200 3phMig C170 3ph
Spot welding 0.2-2.5s 0.2-2,5s 0.2-2.5s
Welding gun connection EURO EURO EURO
Wire dimension range 0.6-0.8(Fe, SS)
1.0(Al)
0.8(FCW)
0.8-1.0(CuSi)
0.6-1.0(Fe, SS)
1.0(Al)
0.8-1.0(FCW)
0.8-1.0(CuSi)
0.6-1.2(Fe, SS)
1.0-1.2(Al)
0.8-1.2(FCW)
0.8-1.0(CuSi)
Max diameter / weight of
wire bobin
300mm/15kg 300mm/15kg 300mm/15kg
Dimensions lxwxh 860x420x730 860x420x730 860x420x730
Weight 63.5kg 72.5kg 82kg
Operating temperature -10 ÷+40°C -10 ÷+40°C -10 ÷+40°C
Transportation temperature -20 ÷+55°C -20 ÷+55°C -20 ÷+55°C
Enclosure class IP 23 IP 23 IP 23
Application classification
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40°C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
4 INSTALLATION
The installation must be carried out by a professional.
Note!
Connect the power source to the electricity mains with a network impedance of 0.268 (C250 3ph) ohm
or lower. If the network impedance is higher, there is a risk of flicker in the illuminators.
CAUTION
This product is intended for industrial use. In a domestic environment this product may
cause radio interference. It is the user's responsibility to take adequate precautions.
4.1 Location
Position the welding power source in such way that its cooling air inlets and outlets
are not obstructed.
GB

- 8 -
ba46e
4.2 Assembly of components
WARNING
For packing and shipment of the machine the wheels are detached from the unit.
Before use attach the wheels according to instruction.
1.
3.
2.
4.3 Electrical installation
C200 3ph
GB

- 9 -
ba46e
4.4 Mains power supply
Check that the unit is connected to the correct mains power supply voltage, and that
it is protected by the correct fuse size. A protective earth connection must be made,
in accordance with regulations.
Rating plate with supply connection data
Recommended fuse sizes and minimum cable area
Mig C170 3ph Mig C200 3ph Mig C250 3ph
Voltage V 400-415V,
3∼50/60 Hz
400-415V,
3∼50/60 Hz
230 / 400-415V,
3∼50/60 Hz
Current A
at 100% duty cycle 4.0 5.3 12.1/7.0
at 60% duty cycle 6.1 6.8 17.6/10.2
at 35% duty cycle 8.9 10.1 25.3/14.6
Mains Cable area mm24 x 1.5 4 x 1.5 4 x 2.5 / 4 x 1.5
Fuse slow A 10 10 25/16
NB: The mains cable areas and fuse sizes shown above are in accordance with Swedish regulations.
They may not be applicable in other countries: make sure that the cable area and fuse sizes comply
with the relevant national regulations.
5 OPERATION
General safety regulations for handling the equipment can be found on
page 4. Read through before you start using the equipment!
WARNING
Rotating parts can cause injury, take great care.
WARNING
To prevent the reel from sliding off the hub: Lock the
reel in place by turning the red knob as shown on the
warning label attached next to the hub.
GB

- 10 -
ba46e
WARNING
Secure the equipment - particularly if the
ground is uneven or sloping.
5.1 Connection and control devices
1Mains supply switch 7Connection for return cable (-), low inductance
2Indicator lamp, power ON/OFF 8Knob for spot welding - ON/OFF and time
setting
3Orange indicator lamp, overheating 9Knob for wire speed setting
4Welding voltage switch 10 Digital instrument - V/A (option,see page 20)
5EURO - connector for welding gun 11 Return cable with return clamp
6Connection for return cable (-), high
inductance
*Knob for burn-back time setting (located on
control board)
C250 3phC170 3ph
C200 3ph
GB