ESAB Aristo Mig WeldCloud U5000i User manual

Aristo®
Instruction manual
0463 666 001 US 20200326 Valid for: serial no. 834-xxx-xxxx
MigU5000iWeldCloud™
460 V

TABLE OF CONTENTS
0463 666 001 © ESAB AB 2020
1SAFETY ....................................................................................................... 4
1.1 Meaning of symbols ............................................................................... 4
1.2 California Proposition 65 Warning........................................................ 4
1.3 Safety precautions ................................................................................. 4
1.4 User responsibility ................................................................................. 8
2INTRODUCTION.......................................................................................... 11
2.1 Equipment ............................................................................................... 11
3TECHNICAL DATA ...................................................................................... 12
4INSTALLATION............................................................................................ 14
4.1 Lifting instructions ................................................................................. 14
4.2 Placing..................................................................................................... 14
4.3 Primary input .......................................................................................... 14
4.4 Terminating resistor ............................................................................... 15
4.5 Connection of multiple wire feed units ................................................ 15
5OPERATION ................................................................................................ 18
5.1 Connections and control devices ......................................................... 19
5.2 Turning on the power source ................................................................ 20
5.3 Fan control .............................................................................................. 20
5.4 Overheating protection .......................................................................... 20
5.5 Cooling unit............................................................................................. 20
5.6 Remote control unit................................................................................ 21
5.7 WeldCloud™ unit.................................................................................... 21
6MAINTENANCE........................................................................................... 22
6.1 Daily......................................................................................................... 22
6.2 If necessary............................................................................................. 22
6.3 Every year ............................................................................................... 23
7TROUBLESHOOTING ................................................................................. 24
8ORDERING SPARE PARTS ........................................................................ 25
DIAGRAM ............................................................................................................ 26
ORDERING NUMBERS....................................................................................... 27
SPARE PARTS LIST............................................................................................ 28
ACCESSORIES ................................................................................................... 29
Rights reserved to alter specifications without notice.

1 SAFETY
0463 666 001 -4- © ESAB AB 2020
1 SAFETY
1.1 Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer's safety practices and
Safety Data Sheets (SDSs).
1.2 California Proposition 65 Warning
WARNING!
Welding or cutting equipment produces fumes or gases that contain chemicals
known in the State of California to cause birth defects and, in some cases, cancer.
(California Health & Safety Code Section 25249.5 et seq.)
WARNING!
This product can expose you to chemicals including lead, which are known to the
state of California to cause cancer and birth defects or other reproductive harm.
Wash hands after use.
For more information, go to www.P65Warnings.ca.gov.
1.3 Safety precautions
WARNING!
These Safety Precautions are for your protection. They summarise precautionary
information from the references listed in Additional Safety Information section. Before
performing any installation or operating procedures, be sure to read and follow the
safety precautions listed below as well as all other manuals, material safety data
sheets, labels, etc. Failure to observe Safety Precautions can result in injury or death.

1 SAFETY
0463 666 001 -5- © ESAB AB 2020
PROTECT YOURSELF AND OTHERS
Some welding, cutting and gouging processes are noisy and require
hearing protection. The arc, like the sun, emits ultraviolet (UV) and
other radiation and can injure the skin and eyes. Hot metal can cause
burns. Training in the proper use of the processes and equipment is
essential to prevent accidents. Therefore:
1. Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes
when welding or watching.
2. Always wear safety glasses with side shields in any work area, even if welding
helmets, face shields and goggles are also required.
3. Use a face shield fitted with the correct filter and cover plates to protect your eyes,
face, neck and ears from sparks and rays of the arc when operating or observing
operations. Warn bystanders not to look at the arc and not to expose themselves to
the rays of the electric-arc or hot metal.
4. Wear flameproof gauntlet-type gloves, heavy long-sleeve shirt, cuffless pants,
high-topped shoes, and a welding helmet or cap for protection, to protect against arc
rays and hot sparks or hot metal. A flameproof apron may also be desirable as
protection against radiated heat and sparks.
5. Hot sparks or metal can lodge in rolled up sleeves, trouser cuffs, or pockets. Sleeves
and collars should be kept buttoned and open pockets eliminated from the front of the
clothing.
6. Protect other personnel from arc rays and hot sparks with a suitable non-flammable
partition or curtains.
7. Use goggles over safety glasses when chipping slag or grinding. Chipped slag may be
hot and can fly for long distances. Bystanders should also wear goggles over safety
glasses.
FIRES AND EXPLOSIONS
The heat from flames and arcs can start fires. Hot slag or sparks can
also cause fires and explosions. Therefore:
1. Protect yourself and others from flying sparks and hot metal.
2. Move all combustible materials well away from the work area or cover the materials
with a protective non-flammable covering. Combustible materials include wood, cloth,
sawdust, liquid and gas fuels, solvents, paints, and coating paper, etc.
3. Hot sparks or hot metal can fall through cracks or crevices in floors or wall openings
and cause a hidden smoldering fire or fires on the floor below. Make certain that such
openings are protected from hot sparks and metal.
4. Do not weld, cut, or perform other hot work until the work piece has been completely
cleaned so that there are no substances on the work piece which might produce
flammable or toxic vapors. Do not perform hot work on closed containers, they may
explode.
5. Have fire extinguishing equipment handy for instant use, such as a garden hose,
water pail, sand bucket, or portable fire extinguisher. Be sure you are trained in its
use.
6. Do not use equipment beyond its ratings. For example, an overloaded welding cable
can overheat and create a fire hazard.
7. After completing work, inspect the work area to make sure there are no hot sparks or
hot metal that could cause a fire later. Use fire watchers when necessary.

1 SAFETY
0463 666 001 -6- © ESAB AB 2020
ELECTRICAL SHOCK
Contact between live electrical parts and earth can cause severe injury
or death. DO NOT use AC welding current in damp areas, if movement
is confined, or if there is danger of falling. Therefore:
1. Be sure the power source frame (chassis) is connected to the earth system of the
input power.
2. Connect the workpiece to a good electrical earth.
3. Connect the work cable to the workpiece. A poor or missing connection can expose
you or others to a fatal shock.
4. Use well-maintained equipment. Replace worn or damaged cables.
5. Keep everything dry, including clothing, work area, cables, torch/electrode holder and
power source.
6. Make sure that all parts of your body are insulated from both the work piece and from
the ground.
7. Do not stand directly on metal or the ground while working in tight quarters or a damp
area; stand on dry boards or an insulating platform and wear rubber-soled shoes.
8. Put on dry, hole-free gloves before turning on the power.
9. Turn off the power, before removing your gloves.
10. Refer to ANSI/ASC Standard Z49.1 for specific grounding recommendations. Do not
mistake the work lead for a earth cable.
ELECTRIC AND MAGNETIC FIELDS
May be dangerous. Electric current flowing through any conductor
causes localized Electric and Magnetic Fields (EMF). Welding and
cutting current creates EMF around welding cables and welding
machines. Therefore:
1. Welders with pacemakers fitted should consult their doctor before welding. EMF may
interfere with some pacemakers.
2. Exposure to EMF may have other health effects which are unknown.
3. Welders should use the following procedures to minimize exposure to EMF:
a) Route the electrode and work cables together. Secure them with tape when
possible.
b) Never coil the torch or work cable around your body.
c) Do not place your body between the torch and work cables. Route cables on
the same side of your body.
d) Connect the work cable to the workpiece as close as possible to the area being
welded.
e) Keep the welding power source and cables as far away from your body as
possible.
FUMES AND GASES
Fumes and gases, can cause discomfort or harm, particularly in
confined spaces. Shielding gases can cause asphyxiation. Therefore:
1. Keep your head out of the fumes. Do not breathe the fumes and gases.
2. Always provide adequate ventilation in the work area by natural or mechanical means.
Do not weld, cut or gouge on materials such as galvanized steel, stainless steel,
copper, zinc, lead beryllium or cadmium unless positive mechanical ventilation is
provided. Do not breathe in the fumes from these materials.

1 SAFETY
0463 666 001 -7- © ESAB AB 2020
3. Do not operate near degreasing and spraying operations. The heat or arc can react
with chlorinated hydrocarbon vapors to form phosgene, a highly toxic gas, and other
irritant gases.
4. If you develop momentary eye, nose or throat irritation while operating, this is an
indication that the ventilation is not adequate. Stop work and take the necessary steps
to improve ventilation in the work area. Do not continue to operate if physical
discomfort persists.
5. Refer to ANSI/ASC Standard Z49.1 for specific ventilation recommendations.
6. WARNING: This product when used for welding or cutting, produces fumes or gases
that contain chemicals known to the State of California to cause birth defects and in
some cases cancer (California Health & Safety Code §25249.5 et seq.)
CYLINDER HANDLING
Cylinders, if mishandled, can rupture and violently release gas. A
sudden rupture of cylinder valve or relief device can injure or kill.
Therefore:
1. Locate cylinders away from heat, sparks and flames. Never strike an arc on a cylinder.
2. Use the proper gas for the process and use the proper pressure reducing regulator
designed to operate from the compressed gas cylinder. Do not use adapters. Maintain
hoses and fittings in good condition. Follow the manufacturer's operating instructions
for mounting a regulator to a compressed gas cylinder.
3. Always secure cylinders in an upright position, by chain or strap, to suitable hand
trucks, undercarriages, benches, wall, post or racks. Never secure cylinders to work
tables or fixtures where they may become part of an electrical circuit.
4. When not in use, keep cylinder valves closed. Have valve protection cap in place if
regulator is not connected. Secure and move cylinders by using suitable hand trucks.
MOVING PARTS
Moving parts, such as fans, rotors and belts can cause
injury. Therefore:
1. Keep all doors, panels, guards, and covers closed and securely in place.
2. Stop the engine or drive systems before installing or connecting a unit.
3. Have only qualified people remove covers for maintenance and troubleshooting as
necessary
4. To prevent accidental starting of equipment during service, disconnect negative (-)
battery cable from battery.
5. Keep hands, hair, loose clothing and tools away from moving parts.
6. Reinstall panels or covers and close doors when service is finished and before
starting engine.
WARNING!
FALLING EQUIPMENT CAN INJURE
• Only use lifting eye to lift unit. Do NOT use running gear, gas cylinders or any
other accessories.
• Use equipment of adequate capacity to lift and support unit.
• If using lift forks to move unit, be sure forks are long enough to extend beyond
opposite side of unit.
• Keep cables and cords away from moving vehicles when working from an
aerial location.

1 SAFETY
0463 666 001 -8- © ESAB AB 2020
WARNING!
EQUIPMENT MAINTENANCE
Faulty or improperly maintained equipment can cause injury or death.
Therefore:
1. Always have qualified personnel perform the installation, troubleshooting and
maintenance work. Do not perform any electrical work unless you are
qualified to perform such work.
2. Before performing any maintenance work inside a power source, disconnect
the power source from the incoming electrical power.
3. Maintain cables, earthing wire, connections, power cord and power supply in
safe working order. Do not operate any equipment in faulty condition.
4. Do not abuse any equipment or accessories. Keep equipment away from
heat sources such as furnaces, wet conditions such as water puddles, oil or
grease, corrosive atmospheres and inclement weather.
5. Keep all safety devices and cabinet covers in position and in good repair.
6. Use equipment only for its intended purpose. Do not modify it in any manner.
CAUTION!
ADDITIONAL SAFETY INFORMATION
For more information on safe practices for electric arc welding and cutting
equipment, ask your supplier for a copy of “Precautions and Safe Practices for
Arc Welding, Cutting and Gouging.” Form 52-529.
The following publications are recommended:
• ANSI/ASC Z49.1 - “Safety in Welding and Cutting”
• AWS C5.5 - “Recommended Practices for Gas Tungsten Arc Welding”
• AWS C5.6 - “Recommended Practices for Gas Metal Arc welding”
• AWS SP - “Safe practices” - Reprint, Welding Handbook
• ANSI/AWS F4.1 - “Recommended Safe Practices for Welding and Cutting of
Containers That Have Held Hazardous Substances”
• OSHA 29 CFR 1910 - "Safety and health standards"
• CSA W117.2 - "Code for safety in welding and cutting"
• NFPA Standard 51B, “Fire Prevention During Welding, Cutting, and Other Hot
Work"
• CGA Standard P-1, “Precautions for Safe Handling of Compressed Gases in
Cylinders”
• ANSI Z87.1, "Occupational and Educational Personal Eye and Face
Protection Devices"
1.4 User responsibility
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed, in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations, which
could result in injury to the operator and damage to the equipment.

1 SAFETY
0463 666 001 -9- © ESAB AB 2020
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ the location of emergency stops
○ its function
○ the relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorized person is within the working area of the equipment when it is
started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting may cause injury to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
• Install and ground the unit in accordance with instruction manual.
• Do not touch live electrical parts or electrodes with bare skin, wet gloves,
or wet clothing.
• Insulate yourself from work and ground.
• Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Pose health risks
• Welders with pacemakers fitted should consult their doctor before welding.
EMF may interfere with some pacemakers.
• Exposure to EMF may have other health effects which are unknown.
• Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or work
cable around your body. Keep the welding power source and cables
as far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.

1 SAFETY
0463 666 001 - 10 - © ESAB AB 2020
FUMES AND GASES - Can be dangerous to your health
• Keep your head out of the fumes.
• Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.
ARC RAYS - Can injure eyes and burn skin
• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
• Protect bystanders with suitable screens or curtains.
NOISE - Excessive noise can damage hearing
Protect your ears. Use ear defenders or other hearing protection.
MOVING PARTS - Can cause injuries
• Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
• Stop engine before installing or connecting unit.
• Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
• Sparks (spatter) can cause a fire. Make sure there are no inflammable
materials nearby.
• Do not use on closed containers.
HOT SURFACE - Parts can burn
• Do not touch parts bare handed.
• Allow cooling period before working on equipment.
• To handle hot parts, use proper tools and/or insulated welding gloves to
prevent burns.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
This product is solely intended for arc welding.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information, contact your local ESAB dealer or visit us on
our website.

2 INTRODUCTION
0463 666 001 - 11 - © ESAB AB 2020
2 INTRODUCTION
The Mig U5000i WeldCloud™ is a GMAW/TIG welding power source, which can also be
used for SMAW (Shielded Metal Arc Welding).
The manual is valid for:
• Mig U5000i with WeldCloud™ unit
• Mig U5000iw with cooling unit and WeldCloud™ unit
NOTE!
These instructions describe a Mig U5000iw WeldCloud™ with a cooling unit.
The power source is intended for use with the Feed 3004 or Feed 4804 wire feed units.
All the settings are made from the wire feed unit or control box.
The Mig U5000i WeldCloud™ power source is combined with U82and provides a control
box which enables wireless monitoring.
ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
For more information about feed units, refer to the Instruction manuals.
For more information about WeldCloud™, refer to the Quick start guide.
2.1 Equipment
The power source is supplied complete with terminating resistor and instruction manual.

3 TECHNICAL DATA
0463 666 001 - 12 - © ESAB AB 2020
3 TECHNICAL DATA
Mig U5000i WeldCloud™
Main voltage 460 V ±10%, 3~ 50/60 Hz
Main supply Sscmin 8.7 MVA Zmax0.018Ω
Primary current
Imax GMAW (MIG/MAG) 33 A
Imax SMAW (MMA) 34 A
Imax GTAW (TIG) 26 A
No-load power demand in energy-saving mode, 6.5 min. after welding
GTAW/GMAW (TIG/MIG) 45 W
SMAW (MMA) 55 W
Voltage/current range
GMAW (MIG/MAG) 8 - 60 V / 16 - 500 A
SMAW (MMA) 16 - 500 A
GTAW (TIG) 4 - 500 A
Permissible load at GMAW (MIG/MAG)
60 % duty cycle 500 A/39 V
100 % duty cycle 400 A/34 V
Permissible load SMAW (MMA)
60 % duty cycle 500 A/40 V
100 % duty cycle 400 A/36 V
Permissible load at GTAW (TIG)
60 % duty cycle 500 A/30 V
100 % duty cycle 400 A/26 V
Power factor at maximum current (I2)
SMAW (MMA) 58.3/0.91
GTAW (TIG) 58.3/0.90
GMAW (MIG/MAG) 58.3/0.90
Efficiency at maximum current (I2)
SMAW (MMA) 87 %
GTAW (TIG) 82 %
GMAW (MIG/MAG) 83 %
Open-circuit voltage U0max
GMAW (MIG/MAG), GTAW (TIG) without
VRD function 1) 72 - 88 V
SMAW (MMA) without VRD function 1) 68 - 80 V
U0L "Live TIG", VRD function deactivated 2) 79 V
GMAW (MIG/MAG), SMAW (MMA), VRD
function deactivated 2)
59 V

3 TECHNICAL DATA
0463 666 001 - 13 - © ESAB AB 2020
Mig U5000i WeldCloud™
VRD function activated 2) < 35 V
Operating temperature 32to104°F(14to104 °F)
(-10 to +40°C)
Transportation temperature 32to104°F(-4to131 °F)
(-20 to +55 °C)
Dimensions l × w × h
without cooling unit
with cooling unit
24.6 × 15.5 × 19.5 in.
(625 × 394 × 496 mm)
24.6 × 15.5 × 30.6 in.
(625 × 394 × 776 mm)
Continual sound pressure at no-load <70 dB (A)
Weight
without cooling unit
with cooling unit
83 kg (183 lb)
103 kg (227 lb)
Insulation class transformer H
Enclosure class IP23
Application class
1) Valid for power sources without VRD specification on the rating plate.
2) Valid for power sources with VRD specification on the rating plate. The VRD function is
explained in the instruction manuals for the control panel, if the panel has that function.
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 104°F (40°C) or below.
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
Cooling unit
Cooling power 2.0 kW at 104°F (40°C) temp. difference and flow
0.26gal/min
Coolant ESAB's ready mixed coolant
Coolant quantity 1.5 gal
Maximum water flow 0.6 gal/min
Maximum number of water-cooled
welding torches that may be connected
Two GMAW welding torches or
one GTAW torch and one GMAW welding torch

4 INSTALLATION
0463 666 001 - 14 - © ESAB AB 2020
4 INSTALLATION
The installation must be carried out by a professional.
NOTE!
Mains supply requirements
This equipment complies with IEC 61000-3-12 provided that the short-circuit power is
greater than or equal to Sscmin at the interface point between the user's supply and
the public system. It is the responsibility of the installer or user of the equipment to
ensure, by consultation with the distribution network operator if necessary, that the
equipment is connected only to a supply with a short-circuit power greater than or
equal to Sscmin. Refer to the technical data in the TECHNICAL DATA chapter.
4.1 Lifting instructions
Power source Trolley and power source Trolley 2 and power source
4.2 Placing
Position the welding power source such that its cooling air inlets and outlets are not
obstructed.
4.3 Primary input
WARNING!
ELECTRIC SHOCK CAN KILL! PRECAUTIONARY MEASURES SHOULD BE TAKEN
TO PROVIDE MAXIMUM PROTECTION AGAINST ELECTRIC SHOCK. BE SURE
THAT ALL POWER IS OFF BY OPENING THE LINE (WALL) DISCONNECT
SWITCH WHEN PRIMARY ELECTRICAL CONNECTIONS ARE MADE TO THE
POWER SOURCE. BE SURE TO CHECK YOUR INPUT LEADS WITH A
VOLTMETER TO MAKE SURE ALL POWER IS OFF.

4 INSTALLATION
0463 666 001 - 15 - © ESAB AB 2020
Check that the unit is connected to the correct main supply voltage,
and that it is protected by the correct fuse sizes. A protective ground
connection must be made, in accordance with regulations.
Rating plate with supply connection data
Recommended fuse sizes and minimum cable areas
Mig U5000i WeldCloud™ 460 V 3~ 60 Hz
Main voltage 460 V
Main cable area, CU/AWG (mm2)10(6)
Phase current, I RMS 24 A
Fuse, Time Delay 25 A
NOTE!
Sizes per National Electric Code for 90°C rated copper conductors @ 30°C ambient.
Not more than three conductors in raceway or cable. Local codes should be
followed if they specify larger sizes other than those listed above.
4.4 Terminating resistor
In order to avoid communication interference, the ends of the
CAN bus must have terminating resistors.
One end of the CAN bus is at the control panel, which has an
integral terminating resistor. The other end at the power
source must have a terminating resistor, as shown on the
right.
4.5 Connection of multiple wire feed units
With control unit and wire feed units without control panel (M0), you can manage up to 4 wire
feed units from one power source.
You can choose between the following connections:
• 1 GTAW (TIG) torch and 1 GMAW (MIG/MAG) gun (Universal power source required)
• 2 GMAW (MIG/MAG) guns
• 1 GTAW (TIG) torch and 3 GMAW (MIG/MAG) guns (Universal power source required)
• 4 GMAW (MIG/MAG) guns
When welding with water-cooled GMAW guns on all wire feed units, it is recommended to
connect a separate cooling unit for the two extra guns.
We recommend connecting the guns in parallel.

4 INSTALLATION
0463 666 001 - 16 - © ESAB AB 2020
Two wire feed units
A connection kit is required when connecting two wire feed units, see "ACCESSORIES"
chapter.
A. Water connection
B. Welding current connection
C. Control box connection
Four wire feed units
Two connection kits and an extra cooling unit are required when connecting four wire feed
units, see "ACCESSORIES" chapter.

4 INSTALLATION
0463 666 001 - 17 - © ESAB AB 2020
A. Water connection
B. Welding current connection
C. Control box connection

5 OPERATION
0463 666 001 - 18 - © ESAB AB 2020
5 OPERATION
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!

5 OPERATION
0463 666 001 - 19 - © ESAB AB 2020
5.1 Connections and control devices
1Orange indicating lamp - Overheating 58.
3/
14
Red indicating lamp - Wi-Fi Connectivity
2White indicating lamp - Power supply ON 58.
3/
15
Fuse for supply voltage for feeder unit,
42 V
58.
3/
3
Main power supply switch, 0 / 1 / START 58.
3/
16
Connection for Ethernet
58.
3/
4
Connection for start signal from the torch 58.
3/
17
Measure outlet screw terminal Red (+)
58.
3/
5
Connection for gas to the TIG torch 58.
3/
18
Measure outlet screw terminal Black (-)
58.
3/
6
Connection (-) for return cable at SMAW
and GMAW or for welding current cable
at TIG (GTAW)
58.
3/
19
Connection for control cable to the wire
feed unit or to the terminating resistor
58.
3/
7
Connection for remote control 58.
3/
20
Connection for control cable to the wire
feed unit or for the terminating resistor
58.
3/
8
Connection (+) for welding current cable
at SMAW (MMA) welding or for return
cable at TIG (GTAW) welding
58.
3/
21
Connection for gas hose
58.
3/
9
Cooling water filler 58.
3/
22
Connection (+) for welding current cable
to the wire feed unit
58.
3/
10
Connection with ELP1for cooling water
to the TIG torch - BLUE
58.
3/
23
Connection (-) for the return cable wire
feeder unit

5 OPERATION
0463 666 001 - 20 - © ESAB AB 2020
58.
3/
11
Connection for cooling water from the
TIG torch - RED
58.
3/
24
Connection for cooling water to the wire
feed unit - BLUE
58.
3/
12
Antenna 58.
3/
25
Connection for cooling water from the
wire feed unit - RED
58.
3/
13
USB Connectivity
1) ELP = ESAB Logic Pump, see "Cooling unit" section in this chapter.
5.2 Turning on the power source
Turn on the main power by turning switch (7) to the “START” position. Release the switch,
and it will return to the “1” position.
If the main power supply is interrupted while welding is in progress, and then is restored, the
power source will remain de-energized until the switch is again turned manually to the
“START” position.
Turn the unit off by turning the switch to the “0” position.
If the supply power fails or the power source is turned off in the normal manner, the welding
data will be stored so that it is available next time the unit is started.
5.3 Fan control
The power source fans continue to run for 6.5 minutes after welding has stopped, and the
unit switches to energy-saving mode. They start again when welding resumes.
The fans run at reduced speed for welding currents up to 180 A, and at full speed for higher
currents.
5.4 Overheating protection
The power source has two thermal overload trips which operate if the internal temperature
becomes too high, interrupting the welding current and lighting the orange indicating lamp on
the front of the unit. They reset automatically when the temperature has fallen.
5.5 Cooling unit
To ensure problem-free operation, the installation height from the cooling unit to the welding
torch must be max. 7 m. Heights in excess of this can cause problems, such as long starting
times, air bubbles, vacuums, etc.
If an installation height in excess of 7 m is required, we recommend an installation kit
comprising a non-return valve and a solenoid valve, refer to accessories in the
"ACCESSORIES" chapter. Once these valves have been installed, the hose package must
be horizontal during the initial startup so that everything fills with water. Then raise the wire
feed unit and hose package to the high height. Continued safe operation at installation
heights of up to 12 m can now begin.
Water connection (GTAW)
The cooling unit is equipped with an ELP (ESAB Logic Pump) detection system, which
checks that the water hoses are connected.