Escalade American legend al4100 User manual

1-888-996-2729

FAX: 1-866-873-3531

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

Or write to:

Escalade Sports

Customer Service Department

P.O. Box 889

Evansville IN 47706

Your Model Number ____________________

have your model number when inquiring about parts.

[email protected]

Please

Date Code ___________________________

2 - AL4100- - HL

When contacting Escalade Sports please provide your model number, date

code (if applicable) and part number if requesting a replacement part. These

numbers are located on the product, packaging, and this owners manual.

Purchase Date ________________________

PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

AL4100

Make sure you understand the following tips before you begin to assemble your game table.

1. Start all bolts by hand before tightening.

2. Some drawings or images in this manual may not look exactly like your product. Please

read and understand the text before starting each assembly step.

TWO ADULTS ARE REQUIRED TO ASSEMBLE

Assembly Tips

Tools Required:

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND

SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO

ADULTS ARE NEEDED TO ASSEMBLE THIS GAME TABLE.

Allen Wrench (Included)

Furniture Polish and Soft Cotton Cloth

ATTENTION:

THIS 9' ARCADE SPEEDBALL

Featuring Electronic Scoring and LED Lighting

IMPORTANT! READ EACH STEP

IN THIS MANUAL BEFORE YOU

BEGIN THE ASSEMBLY.

Assembly Note: During assembly, correct orientation of all parts is critical for correct assembly.

Please study all diagrams closely.

HARDWARE IDENTIFIER

(To Scale)

H1 - 3.5 mm x 18 mm

Phillips Round

Head Screw

(24 pcs)

H4 - 6 mm x 25 mm

Allen Head Bolt

(16 pcs)

H3 - 3.5 mm x 12 mm

Phillips Round

Head Screw

(98 pcs)

H7 - 3.5 mm x 14 mm

Phillips Round

Head Screw

(12 pcs)

H2 - 3.5 mm x 28 mm

Phillips Round

Head Screw

(28 pcs)

5 - 6.5 mm x 18 mm

Flat Washer

(16 pcs)

H6 - M6 Lock Washer

(16 pcs)

(Not to Scale)

Allen Wrench

(1 pc)

T1 - M6

P1 - Front Leg Apron

(1 pc)

P5 - Target Board

with Scoring Sensors

(1 pc)

P3 - Right Front Leg

(assembles with P18)

(1 pc)

P7 - Right Back

Cabinet Leg

(1 pc)

P8 - Left Back

Cabinet Leg

(1 pc)

P9 - Backboard with Graphic

(1 pc)

P10 - Top Cabinet

Panel for Scorer

(1 pc)

P13 - Left Side Apron

(1 pc)

P17 - Left Leg

(assembles with P2)

(1 pc)

P18 - Right Leg

(assembles with P3)

(1 pc)

P19 - Playfield with

End Ramp

(1 pc)

P14 - Right Side Apron

(1 pc)

P15 - Left Top Rail with

Control Switch and Wiring

(1 pc)

P16 - Right Top Rail

(1 pc)

P11 - Upper Back

Cabinet Board

(1 pc)

P2 - Left Front Leg

(assembles with P17)

(1 pc)

P4 - Ball Stop Bottom Board

(1 pc)

P20 - Wooden Support Brace

(packed with black plastic “L” brackets)

(1 pc)

P12 - Lower Back

Cabinet Board

(1 pc)

P6- Top Rail Plastic

Corner Cap

(2 pcs)

(With ON/OFF switch+ wiring)

PARTS IDENTIFIER

(Not to Scale)

18-1/4’’

11-1/2’’

23-1/2’’

23-1/4’’

80-1/2’’

78-3/8’’

7-1/2’’

3-1/2’’

17’’-3/8’’

17-3/8’’

79-1/4’’

18-1/4’’

4-3/4’’

23-1/2’’

23-5/8’’

23-3/8’’

34-3/8’’

8’’-1/2’’

16-1/2’’

26-1/4’’

12’’

17-3/4’’

58’’

17-3/4’’

7-1/4’’

23-1/2’’

22-3/8’’

7-1/2’’

3-1/2’’

Black

Painting

Black

Painting

P33 - Plastic Connector

(Playfield to Front Leg)

(1 pc)

P27 - Clear Plexiglass

(1 pc)

P26 - Plastic Ball Return

(1 pc)

P25 - End Support Board

(1 pc)

P32 - Right Plastic

Trim Strip

(1 pc)

P29 - Electronic Scorer

(1 pc)

A2 - Ball

(4 pcs)

P30 - Black Plastic

“L” Bracket

(6 pcs)

P22 - Goal Box

Bottom Board

(1 pcs)

P31 - Left Plastic

Trim Strip

(1 pc)

P23 - Metal Connection Plate

(16 pcs)

P24 - Middle Support Board

(2 pcs)

P21 - Connecting Board

(2 pcs)

P28 - Lower Front

Cabinet Board

(1 pc)

A1 - A/C Adapter

ACCESSORIES IDENTIFIER

(Not to Scale)

11-3/4’’

23-3/8’’

22-1/4’’

7-1/8’’

5-5/8’’

6-3/4’’

17-3/4’’

23-3/8’’

19-3/8’’

17-1/4’’

19-3/8’’

23-3/8’’

76-3/4’’

24-3/8’’

17-3/4’’

PARTS REQUIRED

40pcs - H3 Phillips Round head Screw

10pcs - P23 Metal Connection Plate

1pc - P14 Right Side Apron

1pc - P16 Right Top Rail

1pc - P13 Left Side Apron

1pc - P15 Left Top Rail with Control Switch

STEP 1

Attach the P14 Right Side Apron onto the P16 Right Top Rail using the P23 Metal Connection Plates

and the pilot holes on the P14/P16 , using the H3 Phillips Round Head Screws as shown in DETAIL A.

Attach the P13 Left Side Apron onto the P15 Left Top Rail using the P23 Metal Connection Plates and

the pilot holes on P13/P15 ,using the H3 Phillips Round Head Screws as shown in DETAIL B.

Tighten, but DO NOT strip out H3 screws.

P13

P15

Flush

Cord Connection

this end.

nat

Out

w W

ON/OFF Switch is on

this end on bottom.

Angle Cut

3 metal inserts

this end

Laminate Down

P15

P13

P23

Helpful Hint:

The P16 and P15 attaches to

the “EDGE” of P13 and P14.

Please study diagrams closely.

FIGURE 1

DETAIL A

P16

P14

P16

P23

Flush

his ass

d part

fli

aro

Align all

Pilot Holes

3 metal inserts

this end

Laminate Down

Angle Cut

awW

Important：

1-3/8’’ overhang

Important：

1-3/8’’ overhang

Important：

1-3/8’’ overhang

Important：

1-3/8’’ overhang

DETAIL B

P15

NOTE: This assembly must be made

on a flat, smooth, non-abrasive surface.

Assembly Note: During assembly,

correct orientation of all parts is

critical for correct assembly.

Please study all diagrams closely.

PARTS REQUIRED

10pcs - H2 Phillips Round Head Screw

1pc - P19 Playfield with End Ramp

STEP 2

Attach the P19 Playfield onto the STEP 1 Assemblies using the pilot holes and the H2 Philips Round

Screws as shown in FIGURE 2.

Tighten, but DO NOT strip out H2 screws.

FIGURE 2

Assembly Note: During assembly, correct orientation of all parts is critical for correct assembly.

Please study all diagrams closely.

P13

P14

P19

Angled Aprons

this end.

Ramp this end.

Playfield sets down into

the “Lips” --- both sides.

Cord Connector

Flush End Flush End

Flush

Pla

fieldU

side Down

PARTS REQUIRED

4pcs - H2 Phillips Round Head Screw

20pcs - H3 Phillips Round Head Screw

1pc - P18 Right Leg1pc - P1 End Apron

1pc - P2 Left Front Leg

1pc - P3 Right Front Leg

1pc - P17 Left Leg 6pcs - P23 Metal Connection Plate

Laminate down

and curvature down.

STEP 3

Attach the P3 Right Front Leg onto the P18 Right Leg using the P23 Metal Connection Plates, the

pilot holes and the H3 Phillips Round Head Screws as shown in DETAIL C.

Attach the P2 Left Front Leg onto the P17 Left Leg using the P23 Metal Connection Plates, the pilot

holes and the H3 Phillips Round Head Screws as shown in DETAIL D.

Attach the DETAIL C / D Assemblies onto the P1 End Apron using the pilot holes and the H2 Phillips

Round Head Screws as shown in FIGURE 3.

Tighten, but DO NOT strip out H2,H3 screws.

FIGURE 3

DETAIL C DETAIL D

P23

P23 P23

P18

H3 H3

P23

P17

Black Painting. Flush

and matching angles.

Forward

Black Painting. Flush

and matching angles.

Angle Cut Here

Two Screws

only at this time

Notch at top

Two Screws

only at this time

Forward

od u

NOTE: Use the pilot holes for the H2

screws in the “notch” area of the P17

& P18 legs for correct orientation and

assembly of the P1 end apron.

PARTS REQUIRED

4pcs - H1 Phillips Round Head Screw 4pcs - H3 Phillips Round Head Screw

1pc - P33 Plastic Connector (Playfield to Front Leg)

STEP 4

STEP 5

Connect the STEP 3 Front Leg

Assembly onto the Playfield

Assembly using the P33 Plastic

Connector as shown in FIGURE 4.

FIGURE 4

FIGURE 5

Attach the STEP 3 Front Leg

onto the STEP 2 Assembly

using the pilot holes and H1

Phillips Round Screws, H3

Phillips Round Screws as

shown in FIGURE 5.

Tighten, but DO NOT strip

out H1, H3 screws.

P33

H1 H3

Cord this end.

Wood block

factory attached

Second adult needs

to hold in place.

P23 Metal Plate install

2 pcs H3 screws.

No gaps during assembly

DETAIL E

DETAIL F

NOTE: Two differ-

ent H1+ H3 screws.

Fron

Front Leg

Assembly

Playfield Assembly

PARTS REQUIRED

12pcs -H7 Phillips Round Head Screw

2pcs - P24 Middle Support Board

1pc - P25 End Support Board

6pcs - P30 Black Plastic “L” Bracket

PARTS REQUIRED

12pcs - H3 Phillips Round Head Screw

STEP 6

STEP 7

FIGURE 6

FIGURE 7

Attach the P30 Plastic “L” Brackets onto

the P24 / P25 Support Boards using the

pilot holes and the H7 Phillips Round

Screws as shown in FIGURE 6.

Tighten, but DO NOT strip out H3

screws.

Attach the P24 / P25 Support Board

Assemblies onto the Side Aprons using

the pilot holes and the H3 Phillips Round

Screws as shown in FIGURE 7.

Tighten, but DO NOT strip out H3

screws.

Assembly Note: During assembly,

correct orientation of all parts is

critical for correct assembly.

Please study all diagrams closely.

Angled cut up Pilot Holes

These rounded cutouts

must face downward.

P24

P25

P30

Pilot Holes

Flush

Note: 2 pieces P24

P25

P30 H3

DETAIL G

P24

P25

PARTS REQUIRED

6pcs - H4 Allen Head Bolt

6pcs - H5 Flat Washer

6pcs - H6 Lock Washer

2pcs - P21 Connecting Board

PARTS REQUIRED

2pcs - H3 Phillips Round Head Screw

1pc - P20 Wooden Support Brace

1pc -

P26

Plastic Ball Return

STEP 8

STEP 9

FIGURE 8

FIGURE 9

Attach the P20 Wooden Support Brace

onto the P26 Plastic Ball Return using

the H3 Philips Round Screws as

shown in FIGURE 9.

Tighten, but DO NOT strip out H3

screws.

Attach the P21 Connecting Boards onto the inside of the Side

Aprons using the H4 Allen Head Bolts, H5 Flat Washers, H6

Lock Washers as shown in DETAIL H.

Tighten H4 bolts using T1 Allen Wrench--- DO NOT

overtighten.

Assembly Note: During assembly, correct

orientation of all parts is critical for correct

assembly. Please study all diagrams closely.

P20

P26

Locate 2 holes in

the P26 ball return.

Important Note:

Match screws to holes

in wooden brace

Bottom Side

P21

Flush

P21

DETAIL H

PARTS REQUIRED

2pcs - H2 Phillips Round Head Screw

PARTS REQUIRED

4pcs - H2 Phillips Round Head Screw

1pc - P22 Goal Box Bottom Board

STEP 11

STEP 10

NOTE: NEED 2 ADULTS FOR ASSEMBLY

FIGURE 10

FIGURE 11

Install and attach the P26 Plastic Ball Return onto the P24/25 Support Boards using the H2 Philips

Round Screws as shown in DETAIL I.

Tighten, but DO NOT strip out H2 screws.

Attach the P22 Goal Box Bottom Board onto the P25 End Support Board using the H2 Philips

Round Screws as shown in DETAIL J.

Tighten, but DO NOT strip out H2 screws.

P24

P20

P26

P25

P22

P25

Press down

with fingers

Black laminate

face down

DETAIL I

DETAIL J Put P22 under

this block

PARTS REQUIRED

6pcs - H4 Allen Head Bolt

6pcs - H5 Flat Washer

6pcs - H6 Lock Washer

PARTS REQUIRED

4pcs - H2 Phillips Round Head Screw

1pc - P7 Right Back Leg

1pc - P8 Left Back Leg

1pc - P28 Back Board - D

STEP 12

STEP 13

Attach the P28 Lower Front Cabinet Board onto the

P7 / P8 Back Legs using the pilot holes and the H2

Phillips Round Screws as shown in FIGURE 12.

Tighten, but DO NOT strip out H2 screws.

Attach the STEP 12 Assembly onto the

STEP 11 Assembly using the H4 Allen

Head Bolts, H5 Flat Washers, H6 Lock

Washers as shown in FIGURE 13.

Tighten all H4 Bolts using the T1

Allen Wrench--- DO NOT overtigten.

NOTE: NEED 2 ADULTS FOR ASSEMBLY

FIGURE 13

FIGURE 12

Second adult holds here

P28

P21

H6 H5

Laminate to

outside

Laminate to

outside

Laminate to

outside

All Edges Flush

Edges flush and tight.

Make sure no gaps

before tighten.

DETAIL K

Carefully stand between the P7 and

P8 Left and Right Cabinet legs to

install and tighten the H4 bolts .

PARTS REQUIRED

4pcs - H1 Phillips Round Head Screw

1pc - P4 Ball Stop Bottom Board

STEP 14

Attach the P4 Ball Stop Bottom Board onto the P7 / P8 Back Legs using pilot holes and the H1 Phillips

Round Screws as shown in FIGURE 14.

Tighten, but DO NOT strip out H1 screws.

FIGURE 14

P34

Wooden P4 must be on top

of the Ball Return Chute to

prevent ball hang up

Plastic Ball

Return Chute

PARTS REQUIRED

2pcs - H2 Phillips Round Head Screw1pc - P5 Target Board with Scoring Sensors

STEP 16

STEP 15

PARTS REQUIRED

2pcs - H1 Phillips Round Head Screw

1pc - P10 Top Cabinet Panel for Scorer

1pc - P29 Electronic Scorer

Attach the P5 Target Board onto the P7 / P8 Back Legs using the pilot holes and the H2 Phillips

Round Screws as shown in FIGURE 15.

Tighten, but DO NOT strip out H2 screws.

Place the wires of the P29 Electronic

Scorer through the hole in the P10

Top Cabinet Panel.

Attach the P29 Electronic Scorer onto

the P10 Top Cabinet Panel using

pilot holes and the H1 Phillips Round

Screws as shown in FIGURE 16.

Tighten, but DO NOT strip out H1

screws.

Connect Male to female plugs as

shown in DETAIL M.

FIGURE 15

FIGURE 16

NOTE:

Connectors must be turned

correctly in order for them

to properly connect.

P10

P29

Three Ball

Catchers at top

front side of P29

front beveled

side of P10

LED Light Strip

DETAIL L

DETAIL M

NOTE: Need second adult to hold the P7+P8 inward to prevent gaps between P7, P8 and P5.

Will slide down to ball ramp.

4pcs - H1 Phillips Round Head Screw

PARTS REQUIRED

4pcs - H4 Allen Head Bolt

4pcs - H5 Flat Washer

4pcs - H6 Lock Washer

1pc - P9 Backboard with Graphic

STEP 17

Place the P9 Backboard with Graphic onto the P7 / P8 Back Legs as shown in FIGURE 17-1.

Attach the STEP 16 Assembly onto the P7 / P8 Back Legs using the H4 Allen Head Bolts, H5 Flat

Washers, H6 Lock Washers as shown in FIGURE 17-2.

Tighten the H4 Bolts using the T1 Allen Wrench--- DO NOT overtigten.

Attach the P9 Backboard with Graphic onto the P7 / P8 Back Legs using the pilot holes and the H1

Phillips Round Screws as shown in FIGURE 17-3.

Tighten, but DO NOT strip out H1 screws.

FIGURE 17-1 FIGURE 17-2 FIGURE 17-3

P9 H4 H6 H5

Graphic

this side

2 wires go out to

outer back side

Note:Notch is

here for wires

STEP 16

Assembly

PARTS REQUIRED

6pcs - H3 Phillips Round Head Screw

1pc - P27 Clear Plexiglass

STEP 18

Install the P27 Clear Plexiglass onto the P7 / P8 Back Legs and attach onto the P10 Top Cabinet Panel

using pilot holes and the H3 Phillips Round Screws as shown in FIGURE 18.

Tighten, but DO NOT overtighten H3 Screws as this could crack the plexiglass.

FIGURE 18

NOTE:

The groove for the top of the P27 plexiglass is in the lower front side of the P10 top cabinet

panel . If the plexiglass will not easily slip into this groove , it will be necessary to loosen the

4 pcs H4 bolts that hold the P10 top cabinet panel and carefully tap or push it forward thus

moving the groove forward just enough to allow the P27 plexiglass to slip into the groove .

P27

P10

Very carefully slide plexiglass into

the top horizonal groove in P10.

Pilot Holes

NOTE:

Carefully remove protective covering from the plexiglass before installation,

avoid finger prints on the plexiglass by wearing cotton gloves.

PARTS REQUIRED

4pcs - H1 Phillips Round Head Screw

1pc - P12 Lower Back Cabinet Board

PARTS REQUIRED

6pcs - H1 Phillips Round Head Screw

2pcs - H2 Phillips Round Head Screw

1pc - A1 A/C Adapter

STEP 19

STEP 20

Attach the P12 Lower Back Cabinet Board onto the P7 / P8

Back Legs using pilot holes and the H1 Phillips Round

Screws as shown in FIGURE 19.

Tighten, but DO NOT strip out H1 Screws.

Attach the P11 Upper Back Cabinet

Board onto the Back Leg Cabinet using

pilot holes and the H1 and H2 Phillips

Round Screws as shown in FIGURE

20.

Tighten, but DO NOT strip out H1,

H3 Screws.

Plug A1 A/C Adapter into back side of

P29 Electronic Scorer

1pc - P11 Upper Back Cabinet Board

FIGURE 19

FIGURE 20

These 2 screws

are H2

Do not allow A/C Adapter cord to be

a trip hazard.

NOTE: All male/ female connectors

must be turned correctly in order to

plug into each other.

P11

P29

P12

Pilot Holes

This wire is from

the Scorer

This connector is

from the bottom

ON/OFF Switch

PARTS REQUIRED

14pcs - H3 Phillips Round Head Screw

1pc - P31 Left Plastic Trim Strip

1pc - P32 Right Plastic Trim Strip

2pcs - P6 Top Rail Plastic Corner Cap

STEP 21

Attach the P31 / 32 Plastic Trim Strips onto the Cabinet using pilot holes and the H3 Phillips Round

Screws as shown in FIGURE 21.

Attach the P6 Top Rail Plastic Corner Caps onto the Front Legs using pilot holes and the H3 Phillips

Round Screws as shown in FIGURE 21.

Tighten, but DO NOT strip out H3 Screws.

FIGURE 21

P32

P31

Flush

Pilot Holes

Flush

IMPORTANT NOTE:

Smaller side to inside IMPORTANT NOTE:

Longer, wider side to outside

P29 Electronic Scorer

A1 A/C Adapter

C2 LED Strip

ELECTRONIC CONNECTIONS

Replacement of Scorer Sensor

C3 Scoring Sensor

(all factory connected)

C1 ON/OFF Swtich

Target Board to Electronic Scorer

C4 Screw

Unplug the connecting wire first.

NOTE: All male/ female connectors must be turned correctly in order to plug into each other.

Connections 1,2,3,4 are

all made by the customer.

Table of contents

Other ESCALADE Video Gaming Accessories manuals

ESCALADE

ESCALADE Atomic G05305W User manual

ESCALADE

ESCALADE Atomic User manual

ESCALADE

ESCALADE American Legend MANHATTAN User manual

ESCALADE

ESCALADE ESCORELCD User manual

ESCALADE

ESCALADE American Legend Phazer HT600 User manual

ESCALADE AMERICAN LEGEND AL4100 User manual

Popular Video Gaming Accessories manuals by other brands