AMS-8923 Connection Diagram
399800, Rev C A, Initial Release - May, 2010
1, Custom Design - August, 2007 B, Revised Release - April, 2017
C, Revised Release - September, 2021
Revision / Date: ets-lindgren.com ets-lindgren.com
Note: ETS-Lindgren may substitute a similar part with the same functionality for another part.
Product Information Bulletin
:gniwollofehtroftnempihsruoyhtiwdedulcninergdniL-STEehteeS Product Information Bulletin
Safety, regulatory, and other product marking information
Steps to receive your shipment
Steps to return a component for service
ETS-Lindgren calibration service
ETS-Lindgren contact information
© Copyright 2007-2021 by ETS-Lindgren Inc. All Rights Reserved. No part of this document may be copied
by any means without written permission from ETS-Lindgren Inc.
The logo is a registered trademark of ETS-Lindgren Inc.ETS-Lindgren
USA Headquarters
1301 Arrow Point Drive
Cedar Park, TX 78613
Phone: +1.512.531.6400
Please see ets-lindgren.com for a list of all ETS-Lindgren offices.
WARRANTY
.tnempihsruoyhtiwdedulcniehtees,noitamrofniytefaslanoitiddaroF Product Information Bulletin
Safety Information
Laser Danger: Denotes a laser (IEC Class 3B) is part of the operating system of the device. Laser power
range is 5-500 mW.
Visible laser radiation: Avoid exposure to beam. Do not stare into beam or view directly with optical instruments.
Laser Cable
(part# 665092)
Additional cables
(as required by configuration)
HIGH VOLTAGE: Indicates presence of hazardous voltage. Unsafe practice could result in severe personal injury
or death.
CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may void your
warranty if you attempt to service the unit by yourself, disconnect all electrical power before starting. There are
voltages at many points in the instrument that could, if contacted, cause personal injury. Only trained service
personnel should perform adjustments and/or service procedures upon this instrument. Capacitors inside this
instrument may still be CHARGED even when instrument is disconnected from its power source.
BEFORE POWER IS APPLIED TO THIS INSTRUMENT, GROUND IT PROPERLY through the protective conductor
of the AC power cable to a power source provided with protective earth contact. Any interruption of the protective
(grounding) conductor, inside or outside the instrument, or disconnection of the protective earth terminal
could result in personal injury.
These components are required to connect the AMS-8923:
AMS-8923 (shown in chamber)
TRIGGER TX
TX
TX
PHI
(positioner)
THETA
(ring)
CAL
RX
FIBEROPTIC
RIGHT
COMM
DEDICATED
PHI
LASER
SWITCH
ANTENNA
SELECTION
DISPLAY CENTER
PHI
BNC1
CAL
FIXTURE
SWITCHED
PATH
DEDICATED
THETA
SMA1
LEFT
COMM
N4
N2
N3
N1
RX
RX
Feed-Through Panel
(part# 115040)
Converter
(part# 1701159)
Converter
(part# 1701157)
Power Supply
(part# 1705516)
Ring Laser Power Converter
PC
(required units provided by customer)
TEST INSTRUMENT
120
100
80
60
40
20
10
KHz
100
KHz
1
MHz
10
MHz
100
MHz
1
GHz
10
GHz
40
GHz
Test Instrumentation
(required units provided by customer)
Laser Control
(part# 115017)
OF F
ON
A LIG NM E N T LA S E RS
Sensor Position Display
(part# 115014)
Front
Back
MAIN CONTROL SWITCH UNIT
PARTNUMBER 1716548
LINE INPUT:90-250 VAC 50/60 HZ 5A
ACCESSORY OUTPUT CURRENT: 5A MAX
ETS-LINDGREN CEDAR PARK, TX, USA
TRIGGER OUT TX
ETHERNET ETHERNET
RX TX RX DISPLAY
LINE IN
STATUS PHI THETA SWITCHED
I
O
ACCESSORY LINE OUT
180PHI 165 150 135 120 105 90 75 60 45 30 15 0 -15 -30 -45 -60 -75 -90 -105 -120 -135 -150 -165
180THETA 165 150 135 120 105 90 75 60 45 30 15 0 -15 -30 -45 -60 -75 -90 -105 -120 -135 -150 -165
Main Control Switch Unit (MCSU) (part #1716548)
Note: System is not shown with optional components. Optional components include a chair and
goniometer, sold separately.
4-Conductor Cable (part# 660046)
8-Conductor Cable (part# 660047)
BNC Cable (part# 106043-10m)
10-Meter Fiber Optic Cable (part# 705344-10)
