ESP DVR8IP User manual

User’s Manual
Thank you for purchasing our product.
Please read this User’s Manual before
using the product.
STAND-ALONE DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 Channel Digital Video Multiplex Recorder
VER 2.0
The most stable and reliable real stand-alone Digital Video Multiplex Recorder
DIGITAL VIDEO RECORDER
DIGITAL VIDEO RECORDER

ALL ABOUT IMAGE RECOGNITION & PROCESSING
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space limitations.
The lightning flash with an arrowhead symbol within an equilateral triangle is intended
to alert the user to the presence of uninsulated “ dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
presence of important operating and maintenance (Servicing) instructions in the
literature accompanying the appliance.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT
SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.
Attention: installation should be performed by qualified service Personnel only in
accordance with the National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have power supplied to
the unit whenever the power cord is inserted into the power source ; however, the unit
is operational only when the ON-OFF switch is in the ON position. The power cord is
the main power disconnect for all unites.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR

FCC INFORMATION
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
A CLASS A computing device subject to certification by the Commission shall be identified pursuant to
par.2.925 et Seq of the chapter. In addition, the label shall include the following statement:
Where a device is constructed in two or more sections connected by wires and marketed together, the
statement specified in this Section is required to be affixed only to the main control unit.
The users manual or instruction manual for the EUT shall contain the following statement or eqivalent.
Caution : Changes or Modifications not expressly approved by the party responsible for compliance could
void the users authority to operate the equipment.
If the EUT requires accessories such as special shielded cables and/or connectors to enable compliance
with emission limits, the instruction manual for the EUT shall include appropriate instructions on the first
page of the text concerned with the installation of the device that these special accessories must be used
with the device. It is the responsibility of the user to use the needed special accessories supplied with the
equipment.
For a CLASS A digital device or peripheral, the instructions furnished the user shall include the following or
similar statement placed in a prominent location in the text of the manual.
Note : This equipment has been tested and found to comply with the limits for a CLASS a digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of the this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING

1
Chapter 1 . Product package
Chapter 2. Installation procedure
1-1. The contents of package 3
1-2. Name and function of each button (front panel) 4
1-3. Name and function of each button (rear panel) 5
2-1. Camera connection 6
2-2. Monitor connection (Composite monitor) 6
2-3. Monitor connection (S-VHS) 7
2-4. VCR & VIDEO PRINTER connection 7
2-5. Sensor connection 8
2-6. Network connection 8
2-7. HDD connection 9
2-8. Power connection 9
Chapter 3. Operation
3-1. DVR SYSTEM Log-in 10
3-2. Recording 11
3-3. Playback 14
3-4. Set-up 16
1. Basic operation 16
2. CAMERA SETUP 16
3. DISPLAY SETUP 17
4. TIME/DATE SETUP 19
5. RECORD SETUP 19
6. HDD MANAGEMENT 21
7. MISCELLANEOUS SETUP 21
8. TCP/IP SETUP 24
Chap 4. Specification and Configuration
4-1. SPECIFICATIONS 27
4-2. Configuration Stand-alone DVMR 28
4-3. RS-232C Hex-code table 28
4-4. Arrange of RS 485 and RS-232C pin 29
9. FACTORY DEFAULT 26
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR Table of Contents

Before reading this document
1. This document is intended for both the administrator and users of stand alone DVMR.
2. This manual contains information for configuring, managing and using stand alone DVMR properly.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture.
4. Be sure to read this manual before using stand alone DVMR Model, even before installing HDD.
8. For questions and technical assistance of this product, contact your local dealer.
About this document
2
Before installing stand alone DVMR, be sure to thoroughly review and follow the instructions in this
User＊s Manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow
THE instruction in manual for appropriate installation.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Check electricity at the place you want to install the DVMR unit is stable and meets our
electricity requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
6. Several chips on the main board of the DVMR unit and hard disk drive inside the unit generate
heat, and it must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close
up an opening (fresh air in-take) on the right side of the unit..
7. Put the DVMR unit at well-ventilated place and do not put heat-generating objects on the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built-
in ventilation fan of the rack is properly running.
8 channel stand-alone DVMR

Chapter 1 . Product Package
1-1. The contents of package
1. 8 ch stand-alone DVMR unit
ALL ABOUT IMAGE RECOGNIT ION & PROCESSING
Stand-alone DVR
8 channel
Stand-alone DVR
DIGITAL VIDEO RECORDER
Describe how to install and operate this DVMR unit.
4. DC power adapter and power cable
Convert AC 110V or AC 220V into DC 12V to supply to DVMR unit.
3. Remote controller
IR remote controller enables an user to operate DVMR unit apart from the unit.
3
2. User’s manual for 8 ch DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR Product package

4
1. HARD DISK DRAWER
2. MENU : Used to check or change parameters settings in SYSTEM SETUP. After pressing [MENU] button,
input password and press [ENTER] button to enter into SYSTEM SETUP.
3. PLAY/ENTER : Starts playback, and in some functions, it is used as the SELECT key.
Press shortly and it starts playback. If you press this button for a long time, you enter
into GO TO menu to start playback from image you want to start.
4. MODE : Changes screen division. Whenever you press [MODE] button, screen division is changed from
full screen to 4-split screen, 9-split screen in sequence, both in live or playback mode.
To change channel in full screen mode, just press number button.
If you press [MODE] button for a lone time, it changes type of monitor connected to DVMR unit
form COMPOSITE to VGA, or from VGA to COMPOSITE, in case VGA option is included in
DVMR system.
5. P/T : Manages PAN/TILT CONTROLLER. To control PTZ camera connected to DVMR unit, you have to
select model of PTZ camera in PAN TILE CMD SETUP/MISCELLANEOUS SETUP.
6. 1/5,2/6,3/7,4/8 : Chooses each indicated camera in full screen mode. Each button is double number
button, and pressing [1], [2], [3], and [4] for a very short time is for 1, 2, 3, and 4
respectively, and pressing [1], [2], [3], and [4] for a long time is for 5, 6, 7, and 8
respectively.
7. PIP : Assigns PIP (Picture In Picture)
8. FRZ : : Displayed screen is paused.
9. SEQ : To see display screen in rotation from channel number 1, 2, 3, and so on, both in live and playback
mode. It also change Quad screen from 1/2/3/4 to 5/6/7/8.
MENU PLAY MODE P/T PIP FRZ SEQ ZOOM
1234
ENTER
10987
6
5432 1211
10. ZOOM : Enlarges the display screen by 200%. Digital zooming.
11. Remote Controller Sensor Input Window
12. Direction button : [LEFT], [RIGHT], [UP] and [DOWN].
In playback mode, [LEFT] and [RIGHT] buttons are for selecting playback
direction(forward/backward), and [UP] and [DOWN] buttons are for increasing or
decreasing speed of playback.
Setting video system : In the process of booting, we can set video type (NTSC or PAL)
using direction buttons. While you press [UP] and [LEFT] button at the same time, turn
on DC power switch on the front panel to set video type at NTSC. Immediately after you
turn on DC power switch, you shall hear beep sound, and it is set at NTSC and stop
pressing [UP] and [LEFT] button. If you turn on DC power switch with [UP] and [RIGHT]
button pressed, it is set at PAL system. Setting is memorized in the system, and it is not
necessary to do it again in the next booting, unless you change video system of camera.
NOTICE : If the Input window (IR receiver) is covered, the remote controller may not work.
NOTICE : If several buttons are simultaneously or incorrectly pressed, the system may not be operated unproperly.
1
POWER
ALL ABOUT IMAGE RECOGNITION & PROCESSING
OVERWRITE
RECORD
PLAY
SETUP
13
13. LED Lamps : Represent status of operation. OVERWRITE/RECORD/PLAYBACK/SETUP.
5678
8 channel stand-alone DVMR 1. Unit Description
1-2. Name and function each button (front panel)

5
5. LOOP Output
6. VCR Connection
7. MONITOR Connection
8. VGA Connection
10. D/C Power Connection
3. LAN (TCP/IP)
2. Sensor Input/Output
1. RS-232C and RS-485 port Connection
4. Camera Connection
9. S-VHS Connection
NOTICE : When connecting with other applications, be sure to turn off the system.
1
4
2
3
6
7
8
910
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5
DC 12V
VCR
CH1 CH2 CH3 CH4
MONITOR
LOOP
Comm Port
V
G
A
ALARM/ RELAY
CH5 CH6 CH7 CH8
ETHERNET
Co m m Port
RS-232C/485
S-VHS
8 channel stand-alone DVMR 1. Unit Description
1-3. Name and function each button (Rear panel)

2-1. Camera Connection
Connect the camera to the CAMERA INPUT on the Rear Panel of the system.
2-2. Monitor Connection (Composite Connection Method)
Connect the monitor to the MONITOR OUT on the Rear Panel of the system
6
VIDEO
LENS VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear part of CAMERA
VIDEO A
IN OUT
VIDEO C
IN OUT
VIDEO B
IN OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
Notice : Connect camera or monitor to DVMR unit while DC power switch on the front panel is off.
Setting video system : In the process of booting, we can set video type (NTSC or PAL)
using direction buttons. While you press [UP] and [LEFT] button at the same time, turn
on DC power switch on the front panel to set video type at NTSC. Immediately after you
turn on DC power switch, you will hear beep sound, and it is set at NTSC and stop
pressing [UP] and [LEFT] button. If you turn on DC power switch with [UP] and [RIGHT]
button pressed, it is set at PAL system. Setting is memorized in the system, and it is not
necessary to do it again in the next booting, unless you change video system of camera.
Screen positioning : If picture displayed in your monitor is not at the center of monitor, you can relocate
images to make them shown in the middle of monitor.
Press [P/T] button for a long time to enter into screen position mode, and you
can adjust location of pictures using [UP], [DOWN], [LEFT] and [RIGHT]
buttons. Press [P/T] button for a long time again to quit screen positioning mode.
If you press [ENTER] button in the process of screen positioning mode, location
of pictures return to original location set by manufacturer.
VCR
CH1 …... CH8
MONITOR
LOOP
CommPort
V
G
A
VCR
CH1 …... CH8
MONITOR
LOOP
CommPort
V
G
A
8 channel stand-alone DVMR 2. Installation
Chapter 2. Procedure

VCR
CH1 …... CH8
MONITOR
LOOP
CommPort
V
G
A
VCR
CH1 …... CH8
MONITOR
LOOP
CommPort
V
G
A
2-3. Monitor (S-VHS) Connection
Connect S-VIDEO Monitor to MONITOR OUT(S-VHS) on the Rear Panel of the system.
2-4. VCR & VIDEO PRINTER Connection
Connect VCR or VIDEO PRINTER to VCR OUT on the Rear Panel of the system.
7
VIDEO
A
IN OUT
VIDEO
C
IN OUT
VIDEO
B
IN OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
VIDEO PRINTER
VCR
8 channel stand-alone DVMR 2. Installation