HIK VISION ds-7200HVI-sh series User guide

DS-7200H V I/H F I-SH SeriesD V R
Quick Operation Guide
UD.6L0202B0019A01

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
1
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
This manual is applicable to DS-7204HVI-SH, DS-7208HVI-SH, DS-7216HVI-SH; DS-7204HFI-SH,
DS-7208HFI-SH and DS-7216HFI-SH series DVR.
Verify Contents
Verify that the package contents are correct by checking the items against the packing list.
Note: Please contact your dealer for damaged or missing items.!
D V R Pre-Installation
The DS-7200HVI/HFI-SH Series DVR is highly advanced surveillance equipment that should be installed with
care. Please take into consideration the following precautionary steps before installation of the DVR.
1.Keep all liquids away from the DVR.
2.Install the DVR in a well-ventilated and dust-free area.
3.Ensure environmental conditions meet factory specifications.
4.Install a manufacturer recommended HDD.
D V R Installation
During the installation of the DVR:
1.Use brackets for rack mounting.
2.Ensure there is ample room for audio and video cables.
3.When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.
4.Connect both the alarm and RS-485 cable.
5.Allow at least 2cm (~0.75-inch) of space between racks mounted devices.
6.Ensure the DVR is grounded.
7.Environmental temperature should be within the range of -10 ºC ~ 55 ºC, 14ºF ~ 131ºF.
8.Environmental humidity should be within the range of 10% ~ 90%.
Hard Disk Installation
Beforeyou start:
Before installing a hard disk drive (HDD), please make sure the power is disconnected from the DVR. A factory
recommended HDD should be used for this installation.
ToolsRequired: Screwdriver.
To install a HDD on your DVR:
1.Remove the cover from the DVR by unfastening the screws on the back and side.
2.Install the HDD in the HDD rack using the provided screws. Fasten the screws on the bottom to fix
the HDD.

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
2
3.Connect the HDD to the motherboard of the DVR with the included data cable.
4.Connect the power cable to the HDD.
5.Re-install the cover of the DVR and fasten screws.

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
3
F ront Panel
The front panel of DS-7200HVI-SH/DS-7200HFI-SH is shown below:
Table&1&Description&of&Control&Panel&Buttons& &
No.
Name
Function Description
1
P O W E R
POWER indicator turns green when DVR is powered up.
2
ST A T US
STATUS indicator lights in red when HDD is reading/writing.
3
Tx/Rx
Tx/Rx indictor blinks green when network connection is functioning properly.
4
USB Interface
Connects USB mouse or USB flash memory devices.
5
IR Rece iver
Receiver for IR remote.
Rear Panel
DS-7204H V I/H F I-SH :
DS-7216H V I-SH :
Note: The rear panel of DS-7208H V I-S H provides 8 video input interfaces.
DS-7216H F I-SH :
Note: The rear panel of DS-7208H F I-SH provides 8 video input interfaces.

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
4
Table&2&Description&of&Rear&Panel&
No.
Item
Description
1
V I D E O IN
BNC connector for analog video input.
2
V ID E O O U T
BNC connector for video output.
3
USB Interface
Connects USB mouse or USB flash memory devices.
4
H D M I
HDMI video output.
5
V G A
DB15 connector for VGA output. Display local video output and menu.
6
A U DI O IN
RCA connector for audio input.
7
A U DI O O U T
RCA connector for audio output.
8
L A N Interfac e
Connector for LAN (Local Area Network).
9
RS-485 Interface
Connector for RS-485 devices. Connect the D+ and D- terminals to T+
and T- of PTZ receiver respectively.
10
12V
12VDC power supply.
11
P O W E R
Switch for turning on/off the device.
12
G N D
Ground(needs to be connected when DVR starts up)
Peripheral Connections
RS-485 Connections
To connect RS-485 devices (e.g., pan/tilt unit) to the DVR:
Press and hold the orange part of the pluggableblock ; insert signal cables into slots and release the orange part.
Ensure signal cables are in tight.
Note: Make sure the pan/tilt receiver unit is connected to the D+ and D- of the RS-485 terminal of DVR.

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
5
Specifications
Table&3&Specifications&for&DS:7200HVI:SH&
Model
DS-7204 H V I-S H
DS-7208 H V I-S H
DS-7216 H V I-S H
Video/Audio
input
Video compression
H.264
Video input
4-ch
8-ch
16-ch
Video input interface
BNC (1.0 Vp-Sȍ3$/176&VHOI-adaptive
Audio compression
G.711u
Audio input
1-ch, RCA (2.0 Vp-SNȍ
Two-way audio input
1-ch, RCA (2.0 Vp-SNȍXVLQJWKHDXGLRLQSXW
Video/Audio
output
H D M I/V G A output
1-ch, resolution:
1920 ×1080P / 60 Hz ,1600 ×1200 / 60 Hz,1280 ×1024 / 60 Hz,
1280 ×720 / 60 Hz, 1024 ×768 / 60 Hz
C VBS output
1-ch, BNC (1.0 Vp-Sȍ 
resolution: PAL: 704 ×576, NTSC: 704 ×480
Encoding resolution
4CIF / 2CIF / CIF / QCIF
F ramerate
Mode1:
4CIF / 2CIF @ 12 fps
or
CIF / QCIF @ 25 fps
(P) / 30 fps (N)
Mode2:
Channel 1: 4CIF /
2CIF / CIF / QCIF @
25 fps (P) / 30 fps (N),
Channel 2~4: CIF /
QCIF @ 25 fps (P) /
30 fps (N)
Mode1:
4CIF / 2CIF @ 8
fps or
CIF / QCIF @ 25
fps (P) / 30 fps (N)
Mode2:
Channel 1&
Channel 5: 4CIF /
2CIF / CIF / QCIF
@ 25 fps (P) / 30
fps (N),
Other Channels:
CIF / QCIF @ 25
fps (P) / 30 fps (N)
Mode1:
4CIF / 2CIF
@6fps or
CIF / QCIF @ 25
fps (P) / 30 fps
(N) Mode2:
Channel 1: 4CIF /
2CIF / CIF / QCIF
@ 25 fps (P) / 30
fps (N),
Channel 2~16:
CIF / QCIF @
25 fps (P) / 30
fps (N)
Video bit rate
32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)
Audio output
1-FK5&$/LQHDUNȍ
Audio bit rate
64 Kbps
Dual-stream
Support;
Sub-stream: CIF @ 6 fps, QCIF @ 25 fps (P) /30 fps (N))
Stream type
Video, Video & Audio
Synchronous
playback
4-ch
8-ch
16-ch
Hard disk
SA T A
1 SATA interface
Capacity
Up to 4TB capacity

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
6
External
interface
Networ k interface
1, RJ45 10M / 100M Ethernet interface
Serial interface
1 RS-485 interface, half-duplex
USB interface
2, USB 2.0
General
Power supply
12 VDC
Consumption
(without hard disk or
D V D-R/W)
: 
: 
5 W
Wor king temperature
-10 ºC ~+55 ºC
Wor king humidity
10% ~ 90%
Chassis
Standalone 1U chassis
Dimensions
(W D H)
315 ×230 ×45 mm
Weight (without hard
disk or D V D-R/W)
NJ
4 kg
4 kg

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
7
Table&4&Specifications&for&DS:7200HFI:SH&
Model
DS-7204 H F I-S H
DS-7208 H F I-S H
DS-7216H F I-SH
Video/Audio
input
Video compression
H.264
Video input
4-ch
8-ch
16-ch
Video input interface
BNC (1.0 Vp-Sȍ3$/176&VHOI-adaptive
Audio compression
G.711u
Audio input
1-ch, RCA (2.0 Vp-SNȍ
Two-way audio input
1-ch, RCA (2.0 Vp-SNȍXVLQJWKHDXGLRLQSXW
Video/Audio
output
H D M I/V G A output
1-ch, resolution:
1080P:
1920×1080×60Hz
UXGA:
1600×1200×60Hz
SXGA:
1280×1024×60Hz
720P: 1280×720×60Hz
XGA: 1024×768×60Hz
1-ch, resolution:
1080P: 1920×1080×60Hz,
SXGA: 1280×1024×60Hz,
720P: 1280×720×60Hz,
XGA: 1024×768×60Hz
C VBS output
1-ch, BNC (1.0 Vp-Sȍ 
resolution: PAL: 704 ×576, NTSC: 704 ×480
Encoding resolution
4CIF / 2CIF / CIF / QCIF
F ramerate
25 fps (P) / 30 fps (N)
Video bit rate
32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)
Audio output
1-FK5&$/LQHDUNȍ
Audio bit rate
64 Kbps
Dual-stream
Support; Sub-stream: CIF / QCIF @ 25 fps (P) / 30 fps (N))
Stream type
Video, Video & Audio
Synchronous
playback
4-ch
8-ch
16-ch
Hard disk
SA T A
1 SATA interface
2 SATA interfaces
2 SATA interfaces
Capacity
Up to 4TB capacity
External
interface
Networ k interface
1, RJ45 10M / 100M Ethernet interface
Serial interface
1 RS-485 interface, half-duplex
USB interface
2, USB 2.0
General
Power supply
12 VDC
Consumption
(without hard disk or
D V D-R/W)
: 
5 W
20 W
Wor king
temperature
-10 ºC ~+55 ºC
Wor king humidity
10% ~ 90%
Chassis
Standalone 1U chassis
19-inch
rack-mounted 1U
19-inch
rack-mounted 1U

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
8
H DD StorageCalculation Chart
The following chart shows an estimation of storage space used based on recording at one channel for an hour at a
fixed bit rate.
Bit Rate
StorageUsed
96K
42M
128K
56M
160K
70M
192K
84M
224K
98M
256K
112M
320K
140M
384K
168M
448K
196M
512K
225M
640K
281M
768K
337M
896K
393M
1024K
450M
1280K
562M
1536K
675M
1792K
787M
2048K
900M
Note: Please note that supplied values for storage space used is just for reference. Storage space used is estimated
by formulas and may have some deviation from actual value.
chassis
chassis
Dimensions
(W D H)
315 ×230 ×45 mm
445 ×290 ×45 mm
445 ×290 ×45 mm
Weight
(without hard disk or
D V D-R/W)
NJ
4 kg
4 kg

Quick Operation Guide of DS-7200HVI/HFI-SH Series DVR
9
Menu Operation
Menu Structure
The menu structure of the DVR is shown as below:
Startup and Shutdown
Proper startup and shutdown procedures are crucial to expanding the life of the DVR.
Beforeyou start:
&KHFN WKDW WKH YROWDJH RI WKH H[WUD SRZHU VXSSO\ LV WKH VDPH ZLWK WKH GHYLFH¶V UHTXLUHPHQW DQG WKH JURXQG
connection is working properly.
Starting up thedevice :
Steps:
1.Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device.
2.Press the P O W E R button on the rear panel. The Power indicator LED should turn green indicating that the
unit begins to start up.
Shutting down thedevice :
Steps:
1.Enter the Shutdown menu.
Menu > Shutdown