ESP GuardCam LED User manual

COMBINED SECURITY CAMERA LED FLOODLIGHT SYSTEM
GuardCam LED Manual.indd 1 11/01/2018 09:46:17

Table of contents
Contents of package .............................................. 2
Overview.........................................................3
Installation .......................................................5
Setting the date and time of GuardCam LED ..........................6
Insert/remove Micro SD Card .......................................7
Adjusting the Settings .............................................8
Viewing recorded files ............................................11
Technical Specifications ...........................................11
Contents of package
GuardCam LED
1 x Allen Key
2 x Screws
2 x Plastic Masonry Plugs 8GB Micro SD Card
2
User Manual
COMBINED SECURITY CAMERA LED FLOODLIGHT SYSTEM
GuardCam LED Manual.indd 2 11/01/2018 09:46:18

3
Overview
Installation
High power LED
PIR lens
Camera lens
FIG. 1 FIG. 2
IMPORTANT
IF IN ANY DOUBT ABOUT THE INSTALLATION OF THIS PRODUCT, CONSULT A QUALIFIED
ELECTRICIAN
- This product must be grounded
- Do not mount the unit against inflammable surfaces
- The motion detector will not operate correctly if it is installed:
• Near the outlet of a central heating boiler
• Near air conditioning plant
• Pointing directly at moving vehicles
• Within sight of reflections from moving water
• Where other lamps could shine on the detector
BEFORE ATTEMPTING ANY INSTALLATION OR MAINTENANCE, ENSURE THAT THE
ELECTRICAL SUPPLY IS SWITCHED OFF AND THE CIRCUIT FUSES REMOVED OR THE
CIRCUIT BREAKER IS IN THE OFF POSITION.
Please make sure the voltage and polarity are correct before connection. Incorrect voltage
may cause electric shock.
GuardCam LED Manual.indd 3 11/01/2018 09:46:18

4
Note: It is recommend to mount 2M above the ground for optimum performance, do not
mount the fixture below 1.2M. See below figure for details of performance range.
Detection range: 10M x 160°
GuardCam LED Manual.indd 4 11/01/2018 09:46:18

5
1. Place plastic masonry plugs into desired surface aligning holes as shown below. Using
an electric screwdriver, fasten mounting plate directly to surface using screws.
2. Feed the cable through the back mounting box and bush the cable entry to avoid
abrasion to the cable.
3. Wire the unit as follows: (Ensure all wires are connected securely and that no loose
strands are exposed)
4. Make sure the polarity is correct. Double check the connections after wiring. Errors may
damage the motion sensor or cause a fire hazard.
5. Attach the unit to the mounting plate. You will first need to angle the unit back so that
the catch at the top of the mounting plate fits into slot on the back of the unit. Next
lower the unit until holes at the bottom of the mounting plate and unit are flush. Then
screw (screw A) into this hole, tightening carefully.
Please allow 1 minute warm-up time after switching on.
* Push the RESET button after switching on.
Installing GuardCam LED
GuardCam LED Manual.indd 5 11/01/2018 09:46:18

After the file “userconfig.txt” is saved onto SD card, you should insert this SD card
immediately into the lighting no later than 2 minutes otherwise the time will be incorrect.
6
Setting the Date and Time:
GuardCam LED Manual.indd 6 11/01/2018 09:46:18
In order for the correct time & date to display on recorded files;
• Take the supplied micro SD card & place it in the SD / USB adaptor
• Place the adaptor in a spare USB port on PC / Laptop
• Go to web link - https://www.espuk.com/timesetup/
• The correct time & date will be displayed
Click ‘userconfig.txt’ to begin download, when complete, save the file to the micro SD
card location and re-insert into the GuardcamLED, the date and time will update automatically.
The file ‘userconfig.txt’ will be removed automatically.
Click “Generate Config’ to produce the “userconfig.txt” file
If the user can not connect to this link https://www.espuk.com/timesetup/
please follow these steps;
1. Open Notepad on computer;
- Input date and time (ex. 2019-01-02 09:33:33)
- Input “userconfig” as the file name
- Choose .txt for the format
- Save the file
2. Copy userconfig.txt to the root directory of SD card
3. Insert SD card into the card slot, the date and time will update automatically. The
file “userconfig.txt” will be remove automatically.

7
1. Unscrew the underside cover using provided Allen key , then insert the Micro SD card
until it automatically locks into place.
2. The Micro SD card is placed at the bottom of the motion sensor. To remove Micro SD
card, please push in SD once to eject, then pull out.
Insert/remove Micro SD Card:
GuardCam LED Manual.indd 7 11/01/2018 09:46:18

8
Time Control
Turn the time control to”+” side to increase the illumination time (7 minutes max.), turn
the control to “-“ side to reduce the illumination time (5 seconds min.).
Adjusting the Settings
Sensitivity Control
Adjust the detector range of Passive Infrared Motion Sensor (2M ~ 10M)
Selecting Working Mode:
Mode 1
- Light + camera + speaker: all day detection
- Daytime and nighttime: light, camera and speaker are all in operation
Mode 2
- Light at night + camera all day + speaker in the daytime
- Daytime: light is off, camera is on, speaker is on
- Nighttime: light is on, camera is on, speaker is off.
Mode 3
- Light at night + camera all day + speaker at night
- Daytime: light is off, camera is on, speaker is off.
- Nighttime: light is on, camera is on, speaker is on.
GuardCam LED Manual.indd 8 11/01/2018 09:46:18

9
Audio Mode
Pre-set default is“silent mode”, push one time for “pre-recorded message”,push again for
“dog barking”.
Push one more time for the message you just recorded.
.
Reset Button
Restores functions to default settings, press this button in case of system malfunction.
GuardCam LED Manual.indd 9 11/01/2018 09:46:18

10
Recording your own messages (see fig. 9)
Guardcam LED will allow you to record two messages of your own for delivery on
detection. To achieve a good quality playback it is best practice to make these recordings
prior to final installation speaking clearly in an environment free from background noise.
The microphone is located at the base of the unit directly above button A.
Two separate messages may be recorded for a maximum length of 10 seconds each.
To record a message press and hold button A. After the “bleep” release button A and
record your message. When finished press button A again to stop recording, you will here
a double confirmation bleep.
To record a second message simply repeat the process.
To check the recorded message/s press and release button B. Should you wish to delete a
self-recorded message press and hold button B for 3 seconds, a double
bleep will confirm deletion.
NB If you attempt to record a new message without first deleting an old message
you will hear a triple error bleep.
GuardCam LED Manual.indd 10 11/01/2018 09:46:18

11
Technical Specifications
PIR detection angle 160 Deg and detection range up to 10M
Records 20 seconds image recording for image stream: 15fps at 720p
Built in Micro SD Card slot for Micro SD memory card
Micro SD Card slot for additional storage, max memory size up to 32G
Micro SD Card spec.: FAT 16(SD), FAT32(SDHC)
Automatic exposure control, white balance and sharpness
Auto Date & Time stamp
Effective viewing angle: 60 deg
Effective viewing distance: 8M
Image format: AVI File
Powered by AC 220V to 240V (subject to requirement)
Auto light sensor
Sensitivity control
Floodlight time delay control
Viewing image by computer through a card reader.
1. Open the PIR housing from the bottom.
2. To remove Micro SD card, please push in SD once to eject, then pull out.
3. Put the Micro SD Card into a card reader, connect PC and card reader by USB cable (not
included) and open any media player to view the video.
Viewing Recorded Files
Reset button: Please press Reset button in case of system malfunction
Reset
GuardCam LED Manual.indd 11 11/01/2018 09:46:19

Elite Security Products
Unit 7, Target Park, Shawbank Rd
Lakeside, Redditch B98 8YN
Telephone: [phone]
Fax: [phone]
email: [email protected]
E&OE - Errors and omissions excepted. A18
GuardCam LED Manual.indd 12 11/01/2018 09:46:19