Esse WD User manual
ESSE Woodfired Cooker
INSTALLATION INSTRUCTIONS
MODEL: WD
ESSE Engineering Ltd. Limited, Long Ing, Barnoldswick, Lancashire BB18 6BN
Cooker Model:
Serial Number:
Colour:
INFORMATION FOR USE WHEN ORDERING SPARES:
THIS APPLIANCE MUST BE COMMISSIONED BY A HETAS REGISTERED ENGINEER OR A COMPETENT
PERSON. THE WARRANTY CARD MUST BE RETURNED TO ENSURE GUARANTEE VALIDITY
Technical Information
Nominal eat output (total) kW 7.9kW
Nominal eat output (to water) kW 3.0kW
Nominal eat output (to space) kW 4.9kW
Weig t of appliance Kg 370kg
Minimum c imney draug t Pa 12
Mean flue gas temperature °C 164
Flue gas mass flow g/s 9,8
T is appliance is not suitable for installation in a s ared flue system
ADDITIONAL SERVICEABLE PARTS
1. Combuster (shown below)
2. Brick Linings
3. Baffle & plug
08/08
HETAS Approved
GENERAL SAFETY INFORMATION
3
In the U , the installer has a responsibility under the Health and Safety at Work Act 1974 to provide for
the safety of persons carrying out the installation. Attention is drawn to the fact that fire cement is
caustic and hands must be washed thoroughly after use. The appliance is heavy (370 g) and care
must be taken during handling. Although the appliance does not contain asbestos products, it is
possible that asbestos may be disturbed in existing installations and every precaution must be taken.
These instructions give a guide for the installation of the appliance but in no way absolve the
installer from responsibilities to conform to British Standards, in particular BS8303 and BS6461,
relating to the installation of solid fuel appliances. All local regulations including those referring to
national and European standards needs to be complied with when installing this appliance.
Outside of the U , the installer must comply with all local, national & european standards that apply.
Any adjacent combustible material should be far enough away from the appliance so as not to rise
65°C above the room temperature when the appliance is in operation. If necessary, any adjoining
walls should be protected from the effects of heat. Clearances from combustible materials are
20mm from the sides and 40mm from the rear.
It is also recommend that a smoke alarm and appropriate fire safety equipment such as a fire
extinguisher and fire blanket are installed in the kitchen as a safety precaution.
An adequate air supply for combustion and ventilation is required. As this cooker does not exceed
5.0kW nominal heat output (refer to building regs document J). However, in certain circumstances
a purpose provided air vent may be necessary - for example, small or tightly sealed rooms. Air
openings provided for this purpose must not be restricted.
40mm
(1.5”)
Rp 1 Tapping
(WD & W-25 Models only)
45mm
(6”)
655mm
(25.3/16”)
185mm
(7.1/4”)
600mm
(23.5”)
25mm
(1”)
990mm
(38.9”)
7mm 7mm
Non combustible base
416mm
(16.5”)
905mm
(35.5”)
80mm
(3.1”)
Non combustible material
Non combustible material
2
Note: The illustration below provides essential boiler tapping measurements and will help when
selecting the location of the cooker. When installing a WD with a Plus2 module, i e work will need
chasing into the wall behind the Plus2.
lIt should have an internal cross section of no
less than 320 cm.sq (200mm dia.) If a flueliner
is used, it should be 6” diameter and be
made of suitable material for burning wood).
The flue diameter is 6”.
lVoids in the chimney should be avoided, as
these will prevent a steady flue draught. The
appliance flue pipe should pass beyond the
narrowing of the chimney.
lBe terminated at least 1m above roof level
so that the chimney does not terminate in a
pressure zone.
lIf the appliance is installed as a freestanding
appliance, it should not support any part of the
chimney.
lBe connected to this one appliance only.
lBe free from cracks, severe bends, voids
and obstructions.
lNew chimneys must be in accordance with
local regulations.
lThe chimney must be capped to prevent
ingress of rain.
lA flue/chimney access point may also be
required so that the state of the chimney can
be checked and any fallen soot removed.
lExternal flues must be insulated to prevent
heat loss.
lDo not fit an extractor fan in the same room
as the appliance.
lBe a minimum 4.6m high from hob chimney level
to pot.
FLUE DRAUGHT
The chimney can be checked, before the appliance is installed, with a smoke match. If the chimney
doesn’t pull the smoke it may suggest the chimney needs attention.
FLUE DRAUGHT READING
Two flue draught readings should be taken, one with the appliance at minimum firing rate and one at
maximum firing rate. The flue draught test hole must be drilled in the flue pipe as close to the
appliance as possible and before any flue draught stabiliser.
Minimum reading: The appliance should be lit and allowed to warm the flue thoroughly. Close the air
slider control the flue box door and ensure firedoor is fully closed. Allow the burning rate to become
Note: This test is only a guide as an apparently poor flue may improve once the appliance is installed,
lit and the flue is warmed. If, once the appliance is installed, there is any doubt that the chimney is
providing an adequate draught, a flue draught reading should be taken.
Note: The chimney / flue to which this appliance is being connected must be swept and examined
for soundness prior to installation. Remedial action should be taken if required, seeking expert
advice if necessary. Where the chimney is believed to have served an open fire installation it is
possible that a higher flue gas temperature from a closed appliance may loosen deposits that
were firmly adhered, with the consequent risk of flue blockage. It is therefore recommended that
the chimney be swept a second time within a month of regular use after installation.
The successful operation of the cooking appliance relies on the adequate performance of the chimney
to which it is connected. The following chimney guidelines must be followed:
CHIMNEY AND FLUE INFORMATION
5
INSTALLING THE APPLIANCE
FLUE CONNECTION
The flue pipe used to connect the appliance to the chimney is 6” (150mm) in diameter. (A 5”-6” adaptor is
supplied to connect to the flue box of the range.
The flue connection is on the top of the appliance, in the centre at the back.
IMPORTANT INSTALLATION NOTES
1. The installation must allow access for adequate chimney sweeping and flue cleaning.
2. Avoid using bends greater than 45° to the vertical. All flue pipe sections should be as close to the
vertical as possible.
3. All joints in the flue system must be effectively sealed.
4. All flue sockets must face upwards. On completing the installation of the appliance, the chimney,
hearth and walls adjacent to the cooker must conform to local or national regulations currently in force.
In the United ingdom, the appropriate sections of the Building Regulations must be conformed to.
5. Air inlet grilles should be positioned so that they are not liable to blockage.
6. An air extraction device shall not be used in the same room as the appliance unless adequate
additional ventilation is provided.
7. A flue cleaning door should be fitted to provide access for cleaning the flue and chimney.
8. Check the appliance for soundness of seals between castings and main components and that all
supplied parts and fittings are correctly fitted.
9. Ensure the appliance is left operational, the heating system correctly balanced and hand over the
operating instructions and operating tools supplied.
10. Before leaving the installation demonstrate the operation of the appliance to the user. Explain all
controls and flue way access for cleaning.
4
steady. The flue draught reading should now be taken, the minimum required is 12 pascals (0.05” w.g.).
Maximum reading: The air slider control can now be opened to allow the appliance to burn at
maximum rate, and the firedoor open on the first catch. eep the flue box door closed. Take a flue
draught reading.
Ideally, the flue draught readings should range between 12 pascals, 0.12mm (0.05 in wg) and 24
pascals, 2.5 mm (0.1 in wg). Any readings significantly outside this range may indicate the need for
remedial action. Low flue draught symptoms: difficult to light and smoke coming into the room. High
flue draught and fuel burns away very quickly.
FLUE STABILISER
A flue stabiliser can be fitted to reduce the draught through the appliance if the flue draught is too
high. The flue stabiliser should be fitted in the same room as the appliance and be the same size as
the flue pipe.
POSITIONING
The appliance should be sited on non-combustible material.
CHIMNEY AND FLUE
1) Pressure and suction zones created by wind
3) Potential causes of down draught
2) The position of chimney outlets
High flue draught symptoms: fire difficult to control, fuel will not last, cooking too hot, appliance damage, chimney fire.
Cause
External wind conditions combined with chimney terminal
Remedy
Fit stabilizer cowl. Fit flue draught stabilizer.
Low flue draught symptoms: difficult to light and smoke coming into the room.
Cause
Cold chimney
Chimney too short
Down draught
Chimney diameter too large
Chimney obstruction
Restricted air supply
Remedy
Line the chimney
Extend the chimney
Relocate/extend chimney terminal. Fit an anti down
draught cowl
Line the chimney
Clear/sweep the chimney
Check for competing draughts (other chimneys, extractor
hoods/fans). Fit an air vent if the room is sealed.
76
The two connections will be supplied by your installer, both 1” BSP Female (Rp1) – on the left hand side
for hot water. The storage cylinder should be 30-gallon nominal capacity insulated to prevent heat loss
and as close to the cooker as possible. Follow general notes below, item (B) (6), (7) & (8).
These appliances are not suitable for use with sealed (pressurised) systems.
GENERAL NOTES ON WATER SYSTEM
1) The cooker will produce hot water at different rates depending on how it is operated. Heating control is
manual, no thermostat is fitted.
2) The system must be designed to cope with loads between the maximum and minimum output. When
the central heating is turned off there must be sufficient gravity load to absorb 15,000 Btu/h for periods
when the oven is being used for cooking, e.g. Domestic hot water plus gravity operated radiator.
3) An indirect storage cylinder is essential for domestic hot water supply, irrespective of whether the
water supply is hard or soft. Minimum capacity 30 gallons. Cylinder should be as close to cooker as possible.
4) The central heating circuit may be gravity circulation, but a pump system is preferred. To allow heat
from the boiler to be absorbed should there be a pump stoppage on an accelerated circuit, the
primary domestic supply must be gravity operated.
5) Installation as a central heating system alone, i.e. without a domestic supply, is not recommended as
the boiler will produce heat when the cooker is in use, irrespective of central heating demand, and
primary absorption must be provided.
6) Whichever system is chosen the layout must follow established heating engineering practice. To
avoid trapping air in the boiler a 1” BSP connection must be used on the flow trapping, and any
reduction in pipe size thereafter being made on a vertical rising pipe. The cooker must be level when
fitted and the flow pipe must rise from the boiler. A drain cock must be fitted on the lowest point of
the return pipe and a vent to atmosphere at the highest point of each circuit.
7) The cylinder and pipe work should be lagged to avoid heat loss.
8) The static head must not exceed 60 feet of water.
9) The static head must not exceed 2 bar.
HEAT OUTPUT TO WATER
Nominal heat output to water is 3.0 kw (10,000 Btu/l). Installation procedure should follow the above, the
cylinder being as near the cooker as it is possible to avoid long pipe runs and subsequent heat loss.
POWER FLUSH. WATER SYSTEMS
If the appliance is to be fitted onto an existing water system then it must be power flushed prior to the
commissioning of the unit and inhibitor re-added. Failure to carry out this operation will seriously affect
boiler performance and negate any warranty claim.
HOT WATER SYSTEMS Typical DHW Gravity System
OPEN VEN
FEED & EXPANSION
CIS ERN
HEA ING FLOW
4000 B U
GRAVI Y RAD
HEA ING RE URN
DRAIN COCK A HE
LOWES POIN
COLD WA ER
CIS ERN
DRAW OFF
COLD FEED
DRAW COCK
CYLINDER 35-40 GAL
28MM (11/4”) FLOW
& RE URN
PIPE S A S
RE URN
125 MM (5”) FLUE-IN O
150 MM (6”) CHIMNEY
INJEC OR EE
OPEN VEN
FLOW
HO WA ER
HEA ING COOKER
Note: A warm boiler return temperature
is essential to avoid tar deposits on the
boiler faces. 45°C minimum is required.
Other Esse Kitchen Appliance manuals
