Essential Home 0-08612936-8 User manual

OWNER’S MANUAL
KENDALL DINING TABLE
CAUTION: Read owner's manual completely before assembly and use.
Product code: 0-08612936-8
UPC code: 729437125093
Date of purchase: / /

1
1. Use the long end of the Allen wrench to fasten Allen bolts loosely and quickly.
2. Use the short end of the Allen wrench for final tightening.
1. Table-maximum weight load per table is 350 pounds.
1. Please read the assembly instructions prior to assembling this product.
2. To avoid damage, assemble this product on a non-abrasive surface such as carpet.
3. Make sure all bolts, nuts, and screws are tightly fastened before the product is used.
4. Not for commercial use.
5. Care: Wipe with a damp cloth. Use furniture polish or lemon oil on the wood as needed.
Avoid prolonged exposure to moisture.
12
! WARNING: After a few days of initial assembly, retighten all hardware.
Periodically check and retighten the screws every few months.
Please make sure you have all parts before beginning assembly. Please wait until all steps
are completed before tightening bolts, nuts, and screws. We recommend using two people for
assembly.
G E N E R A L I N F O R M AT I O N & T I P S
M A X I M U M R E C O M M E N D E D W E I G H T C A P A C I T Y
C U S T O M E R S E R V I C E I N F O R M AT I O N
Ying Fu Enterprise Co., Ltd.
EMAIL: [email protected]
PHONE: [phone]
8:30 am to 5:00 pm CST, Mon. thru Fri.

2
A. Table Top (not replaceable) B. Table Leg (not replaceable) C. Connecter (not replaceable)
QTY: 1 pc QTY: 2 pcs QTY: 1 pc
D. Wood Block
QTY: 2 pcs
PA R T S L I S T

3
1. Wood Dowel 2. Spring Washer 3. Flat Washer
QTY: 2 pcs QTY: 8 pcs QTY: 8 pcs
4. Bolt 5. Bolt 6. Metal Bullet
Dia 1/4 x 2-1/2 inch L Dia 1/4 x 2 inch L 9 x 20 mm
QTY: 4 pcs QTY: 8 pcs QTY: 4 pcs
7. Allen Wrench
QTY: 1 pc
H A R D W A R E L I S T

4
Diagram #1
Diagram #2
A S S E M B LY I N S T R U C T I O N S
Step 1
1. Insert Wood Dowel (1) into the two ends of Connecter (C) as above shown.
1
C
Step 2
2. Attach the Connector (C) to the Table Leg (B) by inserting Wood Dowel (1) into the
Table Leg (B) as shown in inset (a). Then insert Metal Bullet (6) into the holes on the
Connector (C). Insert Bolts (4) into the Bench Leg (B), and then tighten with Allen
Wrench (7) as shown in inset (b). Repeat the same process to attach the other leg.
Note: Always insert Metal Bullets so that the X on the end of the bullet faces
outward and that the threaded hole is turned vertically for alignment with
bolts.
C
B
1
C
6
6
4
7
B
a
b

5
Diagram #3
A S S E M B LY I N S T R U C T I O N S
Step 3
3. Place the Table Top (A) upside down on a non-abrasive surface such as carpet.
Attach the assembled unit from Step2 to the Table top (A) using Bolts (5), Flat
Washers (3) and Spring Washers (2). Repeat the same process for the other leg.
Tighten the bolts (5) with Allen Wrench (7).
b
3 2 5
7
a

6
Diagram #4
A S S E M B LY I N S T R U C T I O N S
Step 4
4. Attach Wood Block (D) to the assembled unit from Step 3 as shown. Attach the other
Wood Block (D) following same process.
5. Turn the Table upright. The table is now ready to use.
D

7
Please refer to part numbers when reordering
For questions or comments about product:
Email: [email protected]
Made in / Hecho en VIETNAM. Distributed by Kmart Corporation, Hoffman Estates, IL 60179
SHOP kmart.com