ETC ColorSource CYC v1.7 User manual

ETC Installation Guide
ColorSource CYC v1.7
Corpora te He adqua rte rs Middleton, WI, USA [phone]
London, UK [phone] Holzkirc he n, DE [phone]
Rome , IT [phone] Hong Kong [phone] Paris, FR [phone]
Web etcconnect.com Support support.etcconnect.com
Conta ct etcconnect.com/contactETC © 2020 Electronic Theatre Controls, Inc.
Product information and specifications subject to change. ETC intends this document
to be provided in its entirety. Trademark and patent info:etcconnect.com/ip
7415M2100-1.7 Rev C Released 2020-03
Overview
The ColorSource CYC is an affordable LED fixture that uses the RGBI-L (red,
green, blue, indigo, and lime) color system to provide a rich, bright light.
Note: Features described in this document require the latest version
of software. For information on updating fixture software, see Update
the Fixture Software on page9.
Safety
For professional use only. Read the entire manual before using this
equipment.
CAUTION:
•
Risk of eye injury. Do not stare directly into the light.
•
Do not operate in proximity to flammable materials.
WARNING: Disconnect the fixture from power and DMX and
allow it to cool before performing any cleaning and maintenance.

ETC Installation Guide
ColorSource CYC v1.7
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
•
Do not use outdoors.
•
Do not let power supply cords touch hot surfaces.
•
Do not mount near gas or electric heaters.
•
Equipment should be mounted in locations and at heights where it
will not readily be subjected to tampering by unauthorized
personnel.
•
The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
•
Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS
Note: The light source in this luminaire is not user-replaceable, and
must be replaced only by a qualified technician. Contact ETC
Customer Support for assistance.
Environment
The ColorSource CYC operates in ambient temperatures of 0°C–40°C. The
ColorSourceCYC is for indoor use only.
•
Maximum recommended ambient operating temperature: Ta=40°C
(104°F)
•
Maximum anticipated external surface temperature at 40°C ambient:
Tmax = 110°C (230°F)
•
External temperatures after 5 minutes of full-brightness operation at
25°C (77°F) ambient: 49°C (119°F)
•
External Temperature (steady state achieved) at 25°C (77°F): 88°C
(190°F)
ColorSource CYC Page 2 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Electrical
•
Operates between 100V and 240VAC at a frequency of 50/60Hz.
•
Maximum power consumption is 160 W.
•
Up to 9 luminaires(15 A max) may be linked via power thru connector
(10 luminaires total per circuit) when used with an R20Relay Module
or Unison Echo Relay Panel. Consult breaker trip curves when used
with other equipment. Requires power from a non-dimmable source.
•
Inrush:
-
120 V: 39 A (first half-cycle)
-
240 V: 74 A (first half-cycle)
Typical Power Consumption
100 V 120 V 230 V
Power Current Power Current Power Current
Idle 1.66 W 0.04 A 1.38 W 0.04 A 1.18 W 0.05 A
Direct at Full 133.7 W 1.34 A 132.6 W 1.11 A 130.4 W 0.59 A
Safety cable
anchor point Yoke
locking
knob
Washer
Installation
Mounting
The ColorSource CYC is
designed for floor mounting.
You can also use the yoke
accessory (included) for top-
hang pipe mounting with a
clamp. Use the included yoke
locking knobs and washers
(see image at right) to attach
the yoke accessory to the
fixture. Tilt the fixture so that
the base of the fixture is perpendicular to the cyclorama. See Adjust the Tilt
on page5 .
Safety Cable
The safety cable (or other approved safety device) must be attached to the
fixture when it is mounted using the optional yoke and C-clamp (see image
above).
ColorSource CYC Page 3 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Connectors
•
Power: Two powerCON®connectors for power in and thru
•
Data (DMX512/RDM): Two five-pin XLR connectors OR two
RJ45connectors for data in and thru
Conversion cables are available from ETC. Please contact your ETC customer
service representative and request part number W6538 for RJ45 to female
XLR or part number W6539 for RJ45 to male XLR.
Note: This fixture is not Ethernet/data network compatible.
Note: The ColorSource CYC is not self terminating. You must
terminate the last fixture in line with a 120 Ohm resistor.
XLRterminators are not available from ETC.
To purchase an RJ45 terminator, please contact ETC customer service
and request part number N4086.
Set Up the Fixture
1. Plug the power cord into the powerCON In connector on the rear of
the fixture.
2. Make any power-thru cable connections prior to applying a power
source.
3. Make any DMX connections, and if the fixture is the last in a DMX line,
terminate the fixture. See Connectors above .
4. Position the fixtures appropriately:
•
Setback: Minimum recommended distance from the cyclorama is
2ft (.61m).
•
Spacing: Position the fixtures arrayed with a 1.7-1 spacing for
optimal coverage, with a maximum spacing of 2-1. For example, if
fixtures are 2 ft (.61 m) from the cyclorama, position them a
maximum of 4 ft (1.22 m) apart from each other.
5. Plug the power cord into the power source.
Power Up
Press any button to wake the display. The display shows the DMX address.
See Set the DMXAddress on the facing page .
You can press the Mode button to access the Presets/Sequences menu. See
Play Presets and Sequences on page7 .
ColorSource CYC Page 4 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Adjust the Tilt
When pipe-mounting the fixture, tilt the fixture so that the base of the fixture
is perpendicular to the cyclorama.
1. Loosen, but do not remove the yoke locking knobs.
2. Tilt the fixture so that the base of the fixture is perpendicular to the
cyclorama.
3. Tighten the yoke locking knobs.
Spill
control
Adjust the Spill
Control
Adjust the angle of the spill
control as needed.
Set the DMXAddress
1. Press any button to wake
the display. The display
shows the DMX address.
2. Use the Up and Down buttons to select the DMX address for the
fixture.
You can also use RDM for DMX addressing. See RDM Values on page10 .
Change the DMXControl Mode
You can set the DMX control mode for the fixture to one of four available
mode options.
1. Press any button to wake the display. The display shows the DMX
address.
2. Press and hold the Mode button for 3 seconds. The display shows the
current DMX control mode.
3. Press the Up button or Down button to change the DMX control
mode:
•
5ch: 5-channel mode (intensity, red, green, blue, and strobe). This
is the default mode.
•
dir: Direct emitter control (intensity, red, green, blue, indigo,
lime, and strobe).
•
1ch: 1-channel mode controls the intensity of preset 1 (defaults
to 3200K White).
•
rgb: RGB mode (red, green, and blue).
4. Press the Mode button to confirm your selection.
ColorSource CYC Page 5 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
The display will automatically return to the DMX address after 10 seconds of
inactivity, and edits to the DMX control mode will not be saved. This cancels
unsaved changes.
Note: Direct mode (dir) on the ColorSource CYC is not a calibrated
mode. As a result, you may see discrepancies in color between
fixtures. ETC recommends operating in one of the calibrated modes,
such as 5-channel mode or RGB mode. (Calibrated modes make
accommodations for the specific LEDs in the array and produce output
that is consistent with other fixtures. Direct mode bypasses this
calibration, and multiple fixtures may produce slightly different
outputs when controlled as a group.)
DMXControl Channels
DMX
Channel
5ch
(5 channel)
dir
(Direct)
1ch
(1 Channel)
rgb
(RGB)
1 Intensity Intensity Intensity Red
2 Red Red Green
3 Green Green Blue
4 Blue Blue
5 Strobe* Indigo
6 Lime
7 Strobe*
*Use DMX values of 0 or 255 for no strobe. Use values of 1–254 to increase the strobe rate
from 1 per second up to 33 per second.
Data Loss Behavior
When DMX data is lost, the fixture does one of the following actions:
•
If you selected a preset or sequence, that preset or sequence
automatically plays.
•
If no preset or sequence is active in the background, the fixture goes
dark and the DMXstart address flashes on the user interface.
ColorSource CYC Page 6 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Play Presets and Sequences
The fixture has twelve factory-configured presets and five factory-configured
sequences. When you play a preset or sequence on a fixture, the same preset
number or sequence number plays on any connected fixtures that are not
receiving DMX. You can re-record presets and sequences through an RDM
device or manually on the fixture. See Re-record Presets on the next page .
1. Press the Mode button to activate the Presets/Sequences menu. The
last active preset or sequence plays automatically. (If DMX data is
present, the current preset or sequence plays in the background and
DMX data continues to take priority.)
2. Press the Up button or Down button as needed to scroll through the
available presets and sequences.
3. To stop the selected preset or sequence, press the Mode button a
second time. The display will revert to show the DMX start address.
Pre-configuredPresets
Preset Name
1 3200 K White
2 5600 K White
3 Red
4 Green
5 Blue
6 Cyan
Preset Name
7 Magenta
8 Yellow
9 Orange
10 Light Yellow
11 Light Blue
12 Light Pink
ColorSource CYC Page 7 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Pre-configuredSequences
Sequence Name
1 Rainbow Fast
2 Rainbow Slow
3 Warm Colors Fast
4 Cool Colors Fast
5 Random
Re-record Presets
1. Using DMX, set the desired levels for the new preset.
2. Press the Mode button to access the Presets/Sequences menu.
3. Press the Up button or Down button to navigate to the preset number
that you want to re-record.
4. Press and hold the Mode button for 3 seconds to confirm the preset
selection. The user interface will show a 3-second countdown. The
preset number blinks once to confirm that the preset has been
recorded.
Note: When the fixture is in Direct mode (dir) or 1-channel mode
(1ch), you cannot re-record presets.
When you re-record presets with the fixture in RGB mode (rgb), the
intensity is set to full and the strobe is turned off.
See Change the DMXControl Mode on page5.
Adjust the Intensity of Presets
1. Ensure that DMX data is not present.
2. Press the Mode button to access the Presets/Sequences menu, and
then press the Up button or Down button to select the preset that you
want to edit.
3. Press and hold the Mode button for 3 seconds. The display shows L:
followed by either an intensity level from 0–99 or FL for full.
4. Press the Up button or Down button to change the intensity level of
the preset in real time.
5. Press the Mode button to confirm your selection and return to the
Presets/Sequences menu.
The display will automatically return to the Presets/Sequences menu after 10
seconds of inactivity, and edits to the preset intensity will not be saved.
ColorSource CYC Page 8 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Lock the User Interface
After you have set up the fixture, you can lock the user interface to prevent
additional changes.
1. Press and hold the Up button and Down button simultaneously for
3seconds. The display will show Loc to indicate that the user interface
is locked.
2. To unlock the user interface, press and hold the Up button and Down
button simultaneously for 3 seconds.
Update the Fixture Software
ETC recommends using UpdaterAtor software to manage software updates.
For more information on UpdaterAtor, see the UpdaterAtor Software Quick
Guide , which you can download for free from etcconnect.com.
When you add a ColorSource fixture running a newer software version or
update a ColorSource fixture to a newer software version using UpdaterAtor,
you can use that fixture to push the newer software version to all connected
ColorSource fixtures, except for ColorSource Spotjr fixtures. ColorSource
Spotjr fixtures can only update (and be updated by)other ColorSource Spotjr
fixtures.
1. Remove power and DMX In from the master fixture that is running the
software version that you want to push to other fixtures.
2. Press and hold the Up button and Down button simultaneously while
restoring power.
3. The display will show Udt rdy to indicate the update mode is
selected.
4. Press the Mode button to start the update process.
•
The display will alternate between Udt and the percentage
complete while updating.
•
The master fixture will reboot once the update is complete.
5. Reconnect DMX In on the master fixture.
Restore Factory Defaults
Press and hold the Mode button, Up button, and Down button
simultaneously for 5 seconds. The DMX start address will blink once to
confirm that defaults have been restored.
Clean the Fixture
If necessary, clean the mirror and diffusion surface with a blast of oil-free air
or wipe with a clean, lint-free cloth. Isopropyl alcohol, distilled water, or a
50%-50% mixture of each can be used to clean the surface.
ColorSource CYC Page 9 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Error Codes
There are three error codes that may be shown on the user interface.
•
CAL: Screen toggles between CAL and ERR to indicate a problem with
the color calibration. The fixture will need to be returned to the ETC
factory; contact your local dealer to set up a repair.
•
OtP: Screen toggles between OtP and ERR to indicate that the fixture
has gone into over-temperature protection mode to avoid damaging
the fixture. Once the fixture has self-cooled, the error will automatically
clear.
•
No App: Screen toggles between no and APP to indicate that the
upgraded fixtures have a software issue. Reload software to clear the
error. If the error persists, contact ETC.
RDM Values
Parameter Value Description
Manufacturer ID 0x6574 Electronic Theatre Controls
Model ID 0x0215 ColorSource CYC
DMXStart Address 0x00F0 Range = 1–512
DMX Personality 0x00E0
1 = 5 Channel
2 = Direct
3 = 1 Channel
4 = RGB
Output Frequency 0x8123 0 = Standard (1.2 kHz)
1 = High (25 kHz)
ColorSource CYC Page 10 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
ColorSource CYC Page 11 of 12 ETC

ETC Installation Guide
ColorSource CYC v1.7
Quick Reference
DMXControl Channels
DMX
Channel
5ch
(5 channel)
dir
(Direct)
1ch
(1 Channel)
rgb
(RGB)
1 Intensity Intensity Intensity Red
2 Red Red Green
3 Green Green Blue
4 Blue Blue
5 Strobe* Indigo
6 Lime
7 Strobe*
*Use DMX values of 0 or 255 for no strobe. Use values of 1–254 to increase the strobe rate
from 1 per second up to 33 per second.
Error Codes
There are three error codes that may be shown on the user interface.
•
CAL: Screen toggles between CAL and ERR to indicate a problem with
the color calibration. The fixture will need to be returned to the ETC
factory; contact your local dealer to set up a repair.
•
OtP: Screen toggles between OtP and ERR to indicate that the fixture
has gone into over-temperature protection mode to avoid damaging
the fixture. Once the fixture has self-cooled, the error will automatically
clear.
•
No App: Screen toggles between no and APP to indicate that the
upgraded fixtures have a software issue. Reload software to clear the
error. If the error persists, contact ETC.
ColorSource CYC Page 12 of 12 ETC