Eureka Ergonomic ERK-EDK-L Quick setup guide

2-Leg Height Adjustable Standing Desk for L shape
Directions For Assembly And Use

When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using the desk.
FAILURE TO COMPLY WITH OR OBSERVE ALL INSTRUCTIONS AND WARNINGS REGARDING THE USE
OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.
DANGER - To reduce the risk of electric shock, always unplug this furnishing from the electrical outlet before
cleaning, or before putting on or taking off parts.
Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled
persons. Keep children away from electric height-adjustable desks, control units, and keypads.There is
a risk of injury and electric shock.
Use this table only for its intended use as described in these instructions. Do not use attachments not
recommended by the manufacturer.
Keep the table close to the power socket/outlet to be easily accessible.
Never operate this table if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water.
Keep the cords away from heated surfaces.
Do not open any of the components: legs, control box, or keypad. There is a danger of electric shock.
Do not insert anything into any seam or opening.
Keep all electrical components away from liquids.
Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
Do not use outdoors.
Inappropriate use of this product may cause property or bodily injury.
Check surroundings on all sides before using the desk. Body parts and property can be crushed if trapped
between an immobile obstacle and the desk’s range of motion.
Ensure the length of power cords are accounted for when operating the desk. Monitors, computers,
speakers, anything with a cord that is not long enough for the desk’s range of motion could be pulled down
or have its wires broken. Items pulled off the desk may cause other items to fall.
Pinch Point : Keep hands and fingers clear.
Please provide this manual to any users, installers, or support personnel operating the product.
MAKE SURE NO OBSTACLES ARE IN THE DESK’S PATH AND ALL CORDS ARE
OF APPROPRIATE LENGTH FOR DESK TRAVEL. FAILURE TO COMPLY WITH
OR OBSERVE ALL ASSEMBLY, SAFETY, AND OPERATION INSTRUCTIONS AND
WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS
PROPERTY DAMAGE OR BODILY INJURY.
This height adjustable desk has an electric motor and is designed for use in dry work areas only. The desk height
is adjustable so that it can be positioned at the most ergonomically suitable height. These desks are designed only
for the purposes included in this manual. They should not be used in environments with high humidity or dampness.
Any other use is at user’s risk.
Do not move around, crawl, or lie under the desk frame. Do not sit or stand on the desk frame.Children should never
use the desk unless they are supervised by adults.
Liability: Under no circumstances does the manufacturer accept warranty claims or liability claims for damages
caused from improper use or handling of the desk frame other than that which is described in this operation manual.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to person:
1. SAFETY AND WARNINGS
USE & LIABILITY

Philips screwdriver and/or power drill Tape measure
TOOLS REQUIRED
[email protected]
844-416-2090
www.eurekaergonomic.com
?

844-416-2090

PARTS
COMPONENTS
P1 P2 P3
×1
×2×1
×1×1
×1
P4 P5 P6
×2
P7 P8 P9
×1×1×1
×1
×1
×8
B
E×10
G
×2
×9
D
×4
C
A×16
×1
F

1.

8×
×8
A
2.
DO NOT tighten the screws at this point .
If you drop a screw inside the Crossbar End , simply tilt to retrieve the screw.

3.
If you are having difficulty inserting any of the screws from Step
3 , it is because some of the installed screws are too tight .
4× ×4
B

4.
×4
B
C×4
4×
4×

5.
!
Left

5.
Right
!

The desk top size should be used is length :53.5'' -72'' width:25"-33"/39''-47''
6.
9×
D×9
Left

The desk top size should be used is length :53.5'' -72'' width:25"-33"/39''-47''
6.
Right
9×
D×9

We recommend that you pre-drill any holes needed for fasteners connecting
the Control Box or Switch to the desktop (if your desktop is not pre-drilled ) .
Never use countersunk screws .
7.
Left
CLICK!
2×
!
E×2

We recommend that you pre-drill any holes needed for fasteners connecting
the Control Box or Switch to the desktop (if your desktop is not pre-drilled ) .
Never use countersunk screws .
7.
Do not overtighten screws in this step.Overtightening
could cause damage to the components.
!
CLICK!
2×
E×2
Right

8.
Make sure all cords are appropriate length to accommodate the change in height.
Left
CLICK!
CLICK!
×1
P8 ×1
P9

8.
Make sure all cords are appropriate length to accommodate the change in height.
Right
CLICK!
CLICK!
×1
P8 ×1
P9

9.
Ensure that the Machine Screws contacts the
Center Rails by sliding the Center Rails as needed .
Left
8×
×8
A

9.
Ensure that the Machine Screws contacts the
Center Rails by sliding the Center Rails as needed .
Right
×8
A
8×

10.
Left
CLICK!
STICK
G
Make sure no obstacles are in the desk's path.
Make sure the desktop is not touching any walls.