Eureka Boss 4D 5892BVZ User manual

Upright Vacuum Cleaner
Household Type
OWNER’S GUIDE
5890- 5909 Series
IMPORTANT
Do not return this product to the store.
For assembly problems or questions
contact: Eureka’s Customer Service
Division toll free at 1-800-282-2886*
For replacement of broken or missing
items to be shipped direct to you, call
1-800-282-2886 or visit our web site,
www.eureka.com.
*En Mexico llame al 5670-6169
PLEASE RETAIN
We suggest you record the model, type and serial
numbers below. They are located on the silver rating
plate on your cleaner. For prompt and complete
service information, always refer to these numbers
when inquiring about service.
Model & Type ___________________________
Serial No. ______________________________
It is also important to keep your receipt as proof of
date of purchase.
Part No. 74227 (5/04) ©2004 Electrolux Home Care Products Ltd. Printed in China
INDEX
Important Information .....................2
Assemble ........................................4
Use .................................................5
Accessories ....................................5
Dust Cup .........................................6
Filter ................................................7
Brush Roll .......................................8
Brush Roll Belt ................................8
How to Remove
Blockages .......................................9
Warranty .......................................10

2
CAUTION: Avoid injury - brush roll will
continue to rotate after special
thermostat shuts off the
suction motor. Follow Thermal
Cut Off instructions.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be
followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury :
• Do not use outdoors or on wet surfaces.
• Store your cleaner indoors, in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them’
• Do not leave vacuum cleaner when plugged in. Turn off the switch and
unplug the electrical cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used
by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended
attachments.
• Do not use with damaged cord or plug. If vacuum cleaner is not working as
it should, has been dropped, damaged, left outdoors, or dropped into water,
return it to a service center before using.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or
pull cord around sharp edges or corners. Do not run vacuum cleaner over
cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying
capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening blocked;
keep free of dust, lint, hair, and anything that may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll.
Keep hair, loose clothing, fingers, and all parts of body away from openings
and moving parts.
• Do not place cleaner on furniture or stairs as the brush roll may cause
damage. Place cleaner on floor with the handle in storage position while
using attachments.
• Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.
• Do not use without dust cup or filter(s) in place.
• Belt pulleys can become hot during normal use. To prevent burns, avoid
touching the belt pulley when servicing the drive belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline, or
use in areas where they may be present.
SAVE THESE INSTRUCTIONS
To reduce the risk of electric shock,
this appliance has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one way.
If the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit,
contact a qualified electrician to install
the proper outlet. Do not change the plug
in any way.
GENERAL INFORMATION
Use the cleaner to pick up dirt and dust
particles. Avoid picking up hard or sharp
objects that could damage the vacuum
cleaner.
Service Information
The instructions in this booklet serve
as a guide to routine maintenance. For
additional service information, telephone
our toll free number for the nearest
Eureka Authorized Warranty Station. You
should know the model, type and serial
number or date code when you call:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to Electrolux
Home Care Products North America,
Consumer Service, P O Box 3900, Peoria,
Illinois, 61612, USA. In Canada, write to
Electrolux Home Care Products Canada,
866 Langs Drive, Cambridge, Ontario
N3H 2N7. Refer to The Eureka Warranty
for complete service information.
DO NOT OIL the motor or the
brush roll. The motor and brush
roll are permanently sealed and
lubricated.
Thermal Cut Off
This vacuum cleaner has a special
thermostat that protects the cleaner in
case of suction motor overheating. If the
suction motor suddenly shuts off, push
the on/off switch off (0) and unplug the
cleaner. Check the cleaner for a possible
source of overheating such as a full dust
cup, a blocked hose or clogged filter. If
these conditions are found, fix them and
wait at least 30 minutes before attempting
to use the cleaner. After the 30 minute
period, plug the cleaner back in and push
the on/off switch on (l). If the cleaner still
does not run, then take it to a Eureka
Authorized Service Center for repair.

3
1. Switch. O position is off. I position turns on suction motor.
II position turns on brush roll motor. For best results use I
position for bare fl oor and II position for carpets and area
rugs.
2. Electronic Brush Speed Control. (On some models.)
Adjust the speed of brush roll revolutions by moving the
slide lower to slow or higher to increase the brush roll
speed. Slow down the brush roll to gently clean area rugs
and carpets.
3. Cord Retainer. To use, push electrical cord down into cord
retainer.
4. Upper Filter Latch. Pull up on latch and rotate cover down
to remove.
5. Upper Filter. Clean the upper fi lter frequently to maintain
good performance.
6. Dust Cup Latch. Rotate counterclockwise to remove dust
cup.
7. Dust Cup. The debris from cleaning is collected in the dust
cup.
8. Dust Cup Handle. Use to remove dust cup after releasing
latch.
9. Handle Release. Step on handle release to pull handle
back to a comfortable operating position.
10. Stair Handle. To use when cleaning stairs.
11. Headlight.
12. Reset Button. To reactivate brush roll if brush roll motor
stops due to being stalled.
13. Cleaner Height Setting. An adjustment that raises or lowers
the cleaner base to match the type of fl oor surface.
14. Brush Roll View Window. To see if brush roll is turning.
WARNING: Avoid injury. Keep loose clothing, hair,
fingers, and all other parts of body
away from any moving part (such as the
revolving brush). Turn off the switch and
unplug the cleaner before changing the
cleaner height setting.
2
5
87
10
13
Helpful Information:
Listen to your cleaner. If you notice a change in the
sound of the motor or a change in performance, it could
simply indicate a common usage or maintenance issue.
Such as, a need to raise or lower the carpet height
adjustment, possible blockage in hose or brush roll
area. These are all easy to fi x and the instructions are
included in this owner’s guide. Becoming familiar with
the information in this guide will help you to get the best
possible performance from your new cleaner for many
years to come.
15. Hose Retainers (4). Place hose in retainers to store hose
on unit.
16. Electrical Cord Hooks (2). Wrap electrical cord around
them to store electrical cord on unit. The upper cord hook
rotates for quick cord release.
17. Nested Wand Storage. The crevice wand stores inside
the larger wand.
18. Carrying Handle. Use this handle to carry unit from one
place to another.
19. Dusting/Upholstery Brush Storage. Store the dusting
brush on back of cleaner.
15
17
16
16
17
18
19
CAUTION: UNPLUG UNIT BEFORE ATEMPTING
TO REMOVE ANY OBJECT WHICH
PREVENTS THE BRUSH ROLL FROM
TURNING.
First, turn off unit, unplug from the electrical socket, then
remove object from brush roll area. Ex: sock, rug, etc.
4
15
15
15
1
6
14
9
Quick Reference
12
11
3
3

CAUTION: Assemble the cleaner before using.
Unit has moving parts, make sure on/
off switch is in off (0) position before
plugging in.
NOTE: Features may vary by model yet all parts
assemble the same.
How to Assemble
Attach Handle
CAUTION: Use special care. Do not pinch electrical
cord between handle and cleaner.
1. From rear of cleaner, align handle with groove and slide
onto cleaner. If necessary, use thumb and finger pressure
to slide handle into position.
2. Attach handle with the two 1 inch screws provided in
the assembly packet. Use a Phillips® head screwdriver.
Guide excess cord though the hole located in the handle
while assembling handle.
NOTE: Hand tighten with screwdriver to be sure
both screws are firmly seated.
Grooves
1
2
3. Pick up hose and lay across upper hose support.
4. Push the end of the hose in the lower hose retainer to
secure.
4
Lower Hose Retainer
Hose
3
Attach Hose
Store Hose and Accessories
Nested Wands
Dusting
Brush
Store Electrical Cord
4
5. You will find your cord retainer on the handle above the
upper cord hook. Firmly push the electrical cord down
into the cord retainer. This will place the cord out of the
way when you vacuum.
6. Next wind the cord around the two cord hooks on the
back side of cleaner.
7. Secure the plug to the cord to prevent unwinding.
Cord Retainer
5
Cord Hook
6
Plug7
Cord Hook
6
Electrical
Cord
Upper Hose
Support

1. To use accessories remove hose from rear of cleaner by
lifting up and twisting.
2. Place desired accessory onto end of hose or wand.
1
2
NOTE: While using accessories, do not place cleaner
on furniture or steps in the operating position
as the brush roll may cause damage. Place
cleaner on fl oor with the handle in storage
position, brush roll will automatically shut off.
• Turn ridge end to center. • Push wands together.
• Grasp both wands near ridges.
Dusting/Upholstery Brush is for furniture, blinds,
books, lamp shades, shelves, curtains, draperies, cushions
and fabrics.
Crevice Wand cleans corners, stairs, baseboards, and
between cushions.
Nested extension wands to add reach.
• Pull apart.
Dusting/Upholstery
Brush
Crevice
Wand
Hose or Wand
5
3
4
5
1. Switch. O position is off. I position turns on suction motor.
II position turns on brush roll motor. For best results use I
position for bare fl oor and position II for carpets and area
rugs.
2. Electronic Brush Speed Control. (On some models.)
Adjust the speed of brush roll revolutions by moving the slide
lower to slow or higher to increase the brush roll speed. Slow
down the brush roll to gently clean area rugs and carpets.
Store
Operate
Clean Under
How to Use
3. Handle Release. Step
on handle release to pull
handle back to a comfortable
operating position. To lower
handle completely to the
floor, depress handle
release a second time.
Helpful Information:
Before cleaning under low furniture, check area fi rst for
objects that might harm the unit or block the vacuum hose.
WARNING: Avoid injury. Keep loose clothing, hair,
fingers, and all other parts of body
away from any moving part (such as the
revolving brush). Turn off the switch and
unplug the cleaner before changing the
vacuum cleaner height.
4. Cleaner Height Setting. An adjustment that raises or lowers
the cleaner base to match the type of fl oor surface. With the
cleaner cord unplugged, set the adjustment to lowest setting
for maximum carpet cleaning. If the cleaner is diffi cult to
push, move adjustment to next highest setting until
cleaner is comfortable to push. The brush roll must reach
the carpet for effective cleaning. For ease in moving the
adjustment knob, place handle in operating position and tilt
cleaner back to remove weight from front wheels.
5. Brush Roll Reset Button. Activates when brushroll is
stalled. Clear the interference, then push button to restart
the brushroll.
NOTE: The brush roll automatically shuts off in
storage position.
WARNING: First turn off the switch and unplug the
cleaner.

The instructions in this booklet serve as a guide to routine
maintenance. To avoid unnecessary service calls, check
the dust cup, fi lters, belt, and brush roll often. We suggest
emptying the dust cup after every use.
NOTE: When vacuuming carpet fresheners or
cleaners, powder, plaster dust, or similar
fi ne substances, the dust cup and fi lters
will require more frequent maintenance.
CAUTION: Turn off the switch and unplug the
electrical cord before changing the
fi lter. Never operate the vacuum cleaner
without the dust cup or fi lter assembly
in place.
Emptying the Dust Cup:
1. Remove dust cup by
rotating the latch counter-
clockwise.
2. Grasp dust cup handle
and pull down and forward
to remove.
3. Remove lid from dust
cup. 4. Dump debris in a waste
container.
Reinstalling the Dust Cup:
1. Replace dust cup lid.
2. To replace the dust cup, hold the handle and slide the
dust cup backwards. There is a groove at the bottom of
the dust cup that aligns with the cleaner.
3. Lock the dust cup in place by rotating the latch
clockwise.
Check and clean the fi lter frequently to maintain
good performance.
6
Instructions to Clean or
Change Dust Cup Filter
Routine Maintenace
1. Remove filter cover by
pulling up latch and
rotating fi lter cover down.
2. Remove filter frame
from cover by pulling the
handle.
3. Remove foam fi lter from
fi lter frame. 4. Shake filter frame and
foam to remove excess
dust. If necessary, the
fi lter frame and foam can
be rinsed in lukewarm
water and air dried.
NOTE: The fi lter frame, foam and cover are not
dishwasher safe.
NOTE: Throughly dry filter and frame before
replacing in cleaner.

(continued)
Filter Door Latch
Sealed HEPA
Cartridge Latch
Models equipped with Cartridge Filter
(Only cartridge style fi lters can be used with these models.)
Check the Sealed HEPA fi lter frequently. Replace twice a year
or as needed.
To remove Sealed HEPA cartridge fi lter
1. Push down on fi lter door latch and pull door away from
cleaner.
2. Push down on Sealed HEPA cartridge latch and remove
fi lter.
To replace Sealed HEPA cartridge fi lter
1. Place bottom tabs of fi lter cartridge into slots. Rotate fi lter
toward cleaner, press fi rmly against cleaner to latch. Make
sure Sealed HEPA cartridge latch is secured on both
sides.
2. Replace fi lter door by placing tabs of door into slots on
cleaner. Rotate door up and against cleaner until it locks
into place.
NOTE: To have the benefi t of a sealed Sealed HEPA
system, you must use one of the Sealed
HEPA cartridge fi lter systems.
Use GENUINE EUREKA replacement Sealed HEPA fi lter,
HF5.
Models equipped with Filter Pads
Check the fi lter pad frequently. Replace twice a year or as
needed.
Filter
Door
Latch
Filter Pad
To remove Filter Pad from fi lter door
1. Push down on fi lter door latch and pull door away from
cleaner.
2. Lift fi lter pad up and out of fi lter door. Dispose of old fi lter
pad.
To replace Filter Pad into fi lter door
1. Place new fi lter pad in fi lter door.
2. Replace fi lter door by placing tabs of door into slots on
cleaner. Rotate door up and against cleaner until it locks
into place.
Use GENUINE EUREKA replacement HEPA fi lter, HF6.
Periodic Maintenance
How To Change Light Bulb
(Only for models with a headlight)
CAUTION: Turn off the power switch and disconnect
the electrical cord before changing light
bulb.
1. Lower handle. Remove the screw from lens cover.
2. Pull lens cover from cleaner.
3. Pull old light bulb out of socket.
4. Push new light bulb into socket.
5. Replace lens cover.
6. Secure with screw.
Use GENUINE EUREKA replacement light bulb,
Part No. 57940-2.
7
Routine Maintenace

Brush Roll
The brush roll turns as it sweeps and combs the carpet nap.
Remove hair and threads from the brush roll so it continues
brushing the carpet. To maintain the most efficient cleaning,
the bristles must touch the carpet. To test the bristle length,
hold a ruler against the underneath side of the cleaner. If the
bristles no longer touch the ruler, replace the brush roll.
Brush Roll Belt
The brush roll belt turns the brush roll to agitate, sweep, and
comb the carpet nap. Cut away any hair or threads wound
around the brush roll because the buildup could cause the belt
to rotate unevenly. The special cog belt should seldom need
replacement. If an unusual circumstance causes belt damage,
call 1-800-282-2886 for nearest Warranty Repair Center.
How To Replace Brush Roll
CAUTION: Turn off the switch and unplug the
electrical cord. Belt pulleys can become
hot during normal use. To prevent injury,
avoid touching the motor shaft.
1. Lower handle to floor. Flip cleaner over.
2. Remove the six screws indicated above with a screwdriver.
One screw is hidden below the wheel carriage. Lift the
wheel carriage in order to reach it.
3. Flip the cleaner back over and lift hood to remove.
NOTE: The carpet height adjustment has to be in
the lowest or highest position to remove or
reinstall the hood.
8
IMPORTANT
10. Rotate brush roll by hand two full rotations
to properly position belt.
11. Place hood back on cleaner. Replace six screws.
12. Tighten screws.
9
4. Lift left end of brush roll.
5. Remove and discard old brush roll.
Brush
Roll
Belt
Motor
Shaft 5
4
6. Place new belt around motor shaft.
7. Place belt around the pully of the new brush roll.
8. Align left end cap with base. Push end cap securely into
place.
9. Push right end cap into base until it snaps into place.
7
8
6
Periodic Maintenace (continued)

Problem Solving
5. Locate lower hose adapter on the side of the cleaner.
6. Remove lower hose adapter from rear of cleaner by lifting
up and twisting.
7. Check for blockages in the hose and base hose. Flexing
the hose may help loosen any blockage. If no blockage
is found, continue to step 8. If blockage is found, clear
and continue to step 11.
8. Remove hood from cleaner and check for a blockage in
the brush roll area. Make sure the hose inlet is clear.
9. After the blockage is found and cleared, replace the hood
on the cleaner.
10. Place lower hose adapter back into the base hose.
11. Install the upper hose adapter onto the back of the
cleaner, line it up with the cleaner opening and push it
against the cleaner until both tabs lock into place.
To Clear Blockages in Hose
CAUTION: Turn off the switch and unplug the
electrical cord before clearing hose.
1. Locate upper hose adapter on the back of the cleaner.
2. Remove nested wands from back of cleaner for easy
access to hose adapter tabs.
3. Press hose adapter tabs together and pull hose adapter
away from cleaner. The hose adapter will unscrew off
hose for easy access to debris if necessary.
4. Check for blockages at cleaner opening and in hose. If
no blockage is found, continue to step 5. If blockage
is found, clear and continue to step 11.
Upper Hose
Adapter Tabs
Nested
Wands Lower
Hose
Adapter
Base
Hose
9

CAUTION: Turn off the switch and unplug the
electrical cord before servicing.
Motor will not start. Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
Motor suddenly Thermal Cut Off, see Page 2.
stops.
Brush roll will not turn. Check for and clear debris in brush roll area. Push
reset button. Page 5. Brush roll will only operate
with handle in operating position.
Does not clean the Clean or replace the filters: Hint: If picking
carpet or floor. up fine dust, the filters may not look dirty, but a fine
substance tends to reduce suction when it blocks
the airflow through the filters.
Be sure the dust cup is properly seated into the
cleaner body. Page 6.
Empty dust cup. Page 6.
Be sure hose adapter is secure on back of cleaner.
Page 9.
Check base hose and long hose. Page 9.
Clean hair and thread from bristles and end cap
area.
Replace brush roll if bristles are worn. Page 8.
Be sure filter is in place. Page 6.
No suction at the Be sure hose adapter is secure. Page 9.
end of hose.
Clean or replace filters. Hint: If picking up fine dust,
the filters may not look dirty, but a fine substance
tends to reduce suction when it blocks the airflow
through the filters.
Remove any clogs from the hose that restrict the
airflow. Check base hose and long hose. Page 9.
Empty dust cup. Be sure dust cup lid is in place and
dust cup is properly seated and secure with latch
engaged. Page 6.
Be sure filter is in place. Page 6.
Headlight not Replace light bulb. Page 7.
working.
Noise from brush Remove hood and clean debris or items from the
roll area. brush roll area. Page 8 / 9
Cleaner is hard to Put handle in operating position. Tilt the
push. cleaner back to raise the front wheels off floor. Then
turn the cleaner height adjustment knob to a higher
setting.
Cleaner height knob Hint: Put handle in operating position. Tilt the
will not turn. cleaner back to raise the front wheels off floor. Then
turn the knob.
Hood will not come off. Hood cannot be removed from cleaner unless the
cleaner height setting is in the lowest or highest
position.
All six screws must be removed from the bottom of
the hood. Page 8.
Missing parts or Eureka’s Customer Service Division toll free at
Questions? 1-800-282-2886*.
PROBLEM SOLUTION
10
THE EUREKA LIMITED WARRANTY
What This Warranty Covers
Your Eureka cleaner is warranted to be free from all defects in material and
workmanship in normal household use for a period of one year. The warranty is granted
only to the original purchaser and members of his or her immediate household. The
warranty is subject to the following provisions.
What This Warranty Does Not Cover
• Parts of the cleaner that require replacement under normal use, such as disposable dust
bags, filters, drive belts, light bulbs, and brush roll bristles, impellers and cleaning.
• Damages or malfunctions caused by negligence, abuse, or use not in accordance with
the Owner’s Guide.
• Defects or damages caused by unauthorized service or the use of other than Genuine
Eureka parts.
What the Manufacturer Will Do
The manufacturer will, at its option, repair or replace a defective cleaner or cleaner part
that is covered by this warranty. As a matter of warranty policy, the manufacturer will
not refund the consumer’s purchase price.
Warranty Registration
Please fill out and return the warranty registration card accompanying your cleaner.
Obtaining Warranty Service
To obtain warranty service you must return the defective cleaner or cleaner part along
with proof of purchase to any Eureka Authorized Warranty Station.
You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners
– Service and Repair.” Be certain that the Warranty Station is “Eureka Authorized.”
For the location of the nearest Eureka Authorized Warranty Station or for service
information, telephone toll free:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer you can write to Electrolux Home Care Products North
America, P O Box 3900, Peoria, Illinois 61612, USA. In Canada write
to Electrolux Home Care Products Canada, 866 Langs Drive, Cambridge,
Ontario N3H 2N7.
If it is necessary to ship the cleaner outside your community to obtain warranty repair,
you must pay the shipping charges to the Eureka Authorized Warranty Station.
Return shipping charges will be paid by the Warranty Station. When returning
parts for repair, please include the model, type, and serial number from the data plate
on the cleaner.
Further Limitations and Exclusions
Any warranty that may be implied in connection with your purchase or use of the
cleaner, including any warranty of Merchantability or any warranty for Fitness For
A Particular Purpose is limited to the duration of this warranty. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitations may
not apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided
above. In no event shall the manufacturer be liable for any consequential or incidental
damages you may incur in connection with your purchase or use of the cleaner. Some
states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which
vary by state.
Questions & Answers about Genuine Eureka Products
Q: Why should I use only Genuine Eureka paper bags, belts, and parts in my Eureka
vacuum cleaner?
A: Using Genuine Eureka Products, which are made to exacting specifications and
engineered with emphasis on quality, performance, and customer satisfaction,
ensures the long life and cleaning efficiency of your vacuum cleaner. Overall,
this saves you money and helps to keep your home clean.
Q: How can I be sure I am using only genuine Eureka products in my vacuum
cleaner?
A: Typically, packaged products and paper bags can be identified by a “Genuine
Eureka Product” symbol (see illustration above). For further identification
assistance, you may call our toll-free number, 1-800-282-2886, for the location
of a nearby Eureka Authorized Warranty Station.
Q: Are there any differences between “made to fit” or “imitation” and Genuine
Eureka paper bags, belts, and parts?
A: Yes, there are some very important differences in materials, quality, and
reliability. Many customers have mistakenly purchased “imitation” paper
bags and parts while thinking they purchased genuine. Unfortunately, many
of these customers discovered the differences after they experienced related
difficulties.
For Genuine Eureka Value, Accept No Imitations!
GENUINE
EUREKA PRODUCT