Eurekazone EZ SMART User manual

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (732 259-9984 [e-mail] www.eurekazone.com
MULTIFORM MASTER TABLE
v13-01
The EZ SMART Multiform Master Table is a lightweight, portable, and adjustable multipurpose work table. The
sliding supports, with user-supplied sacrificial wood, can expand to support a full 4' x 8' sheet of plywood. As
a material support table, it is used in conjunction with the EZ SMART Tracksaw System, EZ SMART Universal
Edge Guide, and the EZ SMART Super Routing Kit. The open top and open slots in the extrusions allow for a
variety of other uses and modifications. The side rail extrusions can also be substituted with other EZ SMART
extrusions to increase its versatility.
PARTS:
(4 Leg Assemblies (2 left and 2 right
(4 Bracket Feet with connectors
(2 Upper End Rail with connectors
(2 Lower End Braces with connectors
(2 48” Side Rails
(4 Sliding Fences with connectors
(4 24” Sliding Plastic Extrusions
(4 8” Sliding Plastic Extrusions
(1 Bag of screws to attach wood to
Sliding Plastic Extrusions

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (732 259-9984 [e-mail] www.eurekazone.com v13-03
ASSEMBLING THE TABLE
STEP 1: Remove the feet from the Leg Assemblies. Set aside.
STEP 2: Remove the connectors from the Upper End Rails. Set aside.
STEP 3: Loosen screws for the T-slot bar on Leg Assembly. Slide Upper End Rail onto
the T-slot bar until aligned with corner. Tighten the screws. Repeat for the other Leg
Assemblies.
T-Slot Bar
STEP 4: Slide the connectors that were removed from the Upper End Rail (Step 2 into the legs
and align with hole in the end of the Upper End Rail. Attach with screw. Repeat for other Leg
Assemblies. The end result will be two End Assemblies.
STEP 5: Loosen screws on the Lower End Brace but do not remove screw or connector. Slide the Lower
End Brace into each Leg of the End Assembly. Place about 10”-12” from bottom of the Leg. Tighten the
screws.

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (732 259-9984 [e-mail] www.eurekazone.com v13-03
STEP 6: Insert Bracket Feet into outer slot of the Legs. Tighten the screws.
STEP 7: Loosen cap screws on underside of the Leg Assembly corner. Slide end of 48” Side Rail over the
corner until flush with the end. Tighten the screws and repeat for the other Side Rail.
STEP 8: Loosen connectors on the Sliding Fences. Insert Fences in to the Side Rails. Locate where
desired and tighten the screws.
Screw Access

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (732 259-9984 [e-mail] www.eurekazone.com v13-03
STEP 9: Insert 24” Sliding Plastic Extrusions into the Sliding Fences. Insert 8” Sliding Plastic Extrusions into
the Side Rails.
STEP 10: Attach user-supplied 1X lumber to the Sliding Plastic Extrusions using the provided self-tapping
screws. Using 4-5 screws per Fence should be sufficient.
Notes: The 1X lumber can be cut to any length though 24” is a common length. Due to the difference in
location of the short Sliding Plastic xtrusions compared to those on the Sliding Fences, the lumber used for
these should be wider.
Completed Mult form Master Table
W th Wood Supports
24” 1x4* 24” 1x3*
* user-supplied lumber
Attach screws
through sides of
plastic extrusions

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone [phone] Fax [phone] Tech (732 259-9984 [e-mail] www.eurekazone.com
USING THE MASTER TABLE
Support ng a full sheet of plywood
Us ng the Un versal Edge Gu de* Us ng the EZ SMART Super Rout ng K t*
and EZ SMART Tracksaw System*
* Sold separately
Us ng the EZ SMART Tracksaw System*
Plywood Top Workbench / Tool Stand Adjustable Legs for Smaller Footpr nt