Euro garden SP31510 User manual

175LB TOW-BEHIND SPREADER
ASSEMBLY AND OPERATION INSTRUCTION MANUAL
HELPFUL HINTS:
READ THE DIRECTIONS BEFORE ASSEMBLY
WHEN ALL ELSE FAILS, READ THE DIRECTIONS AGAIN
If your spreader does not spread evenly, be sure the FRONT on the gear
box points to the front of the spreader. The impeller must turn clockwise.
Reversing the gear box will cause the impeller to turn counter clockwise.
Clean the impeller plate after each use. Fertilizer stuck on the impeller blades
will cause uneven spreading.
Your spreader is designed to be pushed at three miles per hour, which is
a brisk walking speed. Slower or faster speeds will change the spread
patterns. Wet fertilizer will also change the spread pattern and flow rate.
Clean your spreader thoroughly after each use. Wash between the shut off
plate and bottom of the hopper.
Gears are permanently lubricated at the factory. Do not open the gear box
or dirt may enter.

1. Remove and identify loose parts from carton and bag.
Big Flat Washer Ø6

STEP 1:
1.Assembly the first flat washerØ20,the support spacer,the second flat wahsner Ø20,
and the third flat washer Ø20 onto the end of the axle of lnstall tube assembly in
turn.First insert the Ø4x40 cotter pin into the small hole on the axle and then
bend to fix it.(see illustration a).
3.On one end of the axle that has the hole of Ø7,put the pin into the hole on the inboard of
wheel.(see illustration b)
ASSEMBLY INSTRUCTIONS
2. Repeat at the other side of axle.
STEP 2:
1.Insert Hex Bolt M6x50
after aliging the hole at the
flat end of Hitch Tube(stay
on top)with the one at the
middle of
Crossover Tube. Connect
it by using big Flat
Washer Ø6 and lock Nut
M6 and don’t screw it up
moderately. (see
illustration c)
2.Install the Adjustable
Plate Support Tube on the
Hitch Tube using Hex Bolt
M8x50 and Lock Nut
M8(see illustration d)

Step3
Bolt M6x50 and Nylon Lock Nut M6 ,don't screw them up temporarily.(see illustration e)
Plate Support Tube by using Bolt M6x50 and Nylon Lock Nut M6,don't screw them up
temporarily. (see illustration f)
the round part of Install Tube Assembly by using Bolt M6x50 and Nylon Lock Nut M6.
(see illustration g)
4.Adjust the position of
Hitch Tube,Across Rod
and Brace to the properly
location,then tighten all
nuts(in illustration c-g)
up.
1.Connect two Hitch Braces (each at one side) and the hole at the back of Hitch Tube by using
2.Connect two Hitch Braces (each at one side) and the hole at the middle of Adjust
3. Connect another end of two Braces at each side of Hitch Tube with the hole in horizontal direction at
Step 4
of the Hoper Assembly
to make the axle to be
able to twirl freely
and then screw all
the Nylon Nut M6.
(see illustration h)
into the hole on top
of Swivel Axle.
(see illustration i)
3.Insert the R Pin Ø3x75
M6x50 with Big Flat WasherØ 6 and Nylon Flat Washer on the top and six Nylon Lock Nut M6. Adjust parts
2. Aligning all the six holes around Hopper Assembly and the six holes on the Frame by using six Bolt
1. Insert the head of Axle on Frame Tube Assembly into the Swivel Bushing at the bottom of Hopper Assembly

Step 5
2.Put the support rod into the hole on the hopper using Hex Bolts M6x20, Big Flat
WashersØ6 and
Step 6
M8 and don't screw them up moderately.
1. Connect Adjust Handle Assembly and Support Bar by using two Bolts M8x40 and two Nylon Lock Nuts
nylon Lock nuts.
1.Put the Hopper Screen into the end of Hopper Assembly(see illustration j)
2. Install one Flat Washer Ø8 at the lower head of Adjust Rod and then insert into the hole of Rod Base.
Conncet them by using a Nylon Lock Nut M8. (see illustration k and l)
of assembly.
2. Install one Flat Washer Ø8 at the lower head of Adjust Rod and then insert into the hole of Rod Base.
3. Adjust the Adjust Handle back and forth to make the Active Adjustable Plate to be able to fully open
to close. Then screw up the two Nylon Lock Nuts M8 that used to fix the whole set

Step 7
1.Connect the Hitch Break and the head of Hitch Tube by using two Hex Bolts M6x50
and Nylon Lock Nuts M6. Connect them according to the illustration m would be ok
as well.Through this way, the length of Hitch Tube is changed.
Step8
Step8

PARTS DRAWING
PARTS DRAWINGPARTS DRAWING
PARTS DRAWING

PARTS LIST
Ref# QTY Ref# QTY
1 Tire 2 30 Fixing Plate for Wing Nut 1
2 Spacer 2 31 Nylon Flat Washer 12
3 Flat WasherØ20 8 32 Wing Nut M6 1
4 Bushing 2 33 Hex Bolt M8x40 2
5 Cotter Pin Ø4x40 2 34 Hex Bolt M6x20 5
6 Swivel Axle 1 35 Adjust Handle 1
7 Gear (Driver) 1 36 Handle Crip 1
8 Spring Pin Ø4x35 2 37 Big Flat WasherØ6 14
9 Shaft Support Cap 1 38 Bracket 1
10 Drive PinØ6x50 1 39 Flat WahserØ8 4
11 Small Gear 1 40 Bracket,Flow Comtrol Mount 1
12 Turn Axle 1 41 Plastic Cap 1
13 Spring Pin Ø3x16 1 42 Adjust Rod 1
14 Screw M4x20 1 43 Gauge Label 1
15 Impeller 1 44 Bearing 2
16 Hitch Brace 4 45 Fixing Adjustable Plate 1
17 Hex Bolt M6x45 7 46 Active Adjustable Plate 1
18 Hitch Tube 1 47 Fixed Plate for Connecting Rod 1
19 Flow Control Rod 1 48 Spring 1
20 Hex Bolt M8x45 4 49 Base for Spring 1
21 Nylon Lock Nut M8 10 50 Hopper Screen 1
22 Nylon Lock Nut M6 21 51 Support Rod 1
23 Hex Bolt M8x20 2 52 RivetØ5x12 6
24
R Pin Ø3X75
4
53
Hex Bolt M6x50
7
DescriptionDescription
24 R Pin Ø3X75 4 53 Hex Bolt M6x50 7
25 Hitch Bracket 1 54 Hoppper Assembly 1
26 Connect Plate 1 55 Mounting Tube 1
27 Peg 1 56 Across Rod 1
28 Hex Bolt M6x40 1 57 Shaft Support 1
29 Carriage Bolt M6x20 1 58 Rain Cover 1