EUROGUARD 50394 User manual

Item Qty. Code Max. Torque Qty.
1 1 Pza. 50394 - 1
2 1Jgo. 503940DA - 1
1 Pza. BRK-50394 1
3 1Jgo. 5029400 - 1
4 1Jgo. 503944BA Upper bracket A - 1
5 1Jgo. 503944CA Upper bracket B - 1
6 1Jgo. 5029444 Support to upper bracket -
2 Pza. 3 3812 -
8 2 Pza. 5029401 -
9 2 Pza. 5029486 -
1 Pza.
KTE-50394
10 2 Pza. - -
11 2 Pza. -
-
12 2 Pza. - 18 Lb.ft
13 2 Pza. - 9 Lb.ft
14 4 Pza. - -
15 1 Pza. - -
16 4 Pza. - 9 Lb.ft
1 2 Pza. - 31Lb.ft
18 2 Pza. - -
19 2 Pza. - -
20 2 Pza. - 31Lb.ft
21 2 Pza. - 5 Lb.ft
22 4 Pza. - 5 Lb.ft
23 6 Pza. - -
24 4 Pza. - 5 Lb.ft
25 2 Pza. - -
26
2 Pza.
-
5 Lb.ft
50394
ONDA CRV 2010 ( LX - EX - EXL )
EUROGUARD
INSTALLATION INSTRUCTIONS
Parts List Required Tools (Not included)
Socket / Wrench /16" - 3/4" - 9/16"
Socket / Wrench 16mm
Extension to ratchet
Spacer
Rod bolt
Tube spacer
Description Description
Euroguard Ratchet
Brush guard Flat screw driver
ardware brackets kit including: Cuther
Lower bracket
ardware bolt kit including:
Brackets
5/16" Flat washer
5/16" Lock washer
5/16" hex nut
1/4 x 3/4" Hex head bolt
1/4" Flat washer
1/2" Flat washer
1/4" hex nut
3/8" Carriage head bolt
3/8" Flat washer
3/8" Lock washer
3/8" Hex nut
1/2 x 1 1/2" Hex head bolt
1/2" Carriage head bolt
1/2" Lock nut
1/2" Lock washer
1/2" Hex nut
Instructions
1/4" Bolt guide
1
2
3
4
5
6
DriverDriver
Driver
Passenger
Driver
Driver
8
7
1. Before beginning installation, read the instructions thoroughly and
completely. If any of the items listed above are missing, please do not
proceed with the installation. Call your distributor immediately to obtain the
necessary items.
2. Locate the tow hook and remove the factory bolt in the lower front part
of the vehicle. PHOTO 1.
PHOTO 1
Remove this bolt.
Tow hook
3. Attach the longer leg of the lower bracket using the tow hook bolt
removed in Step 2. Attach the shorter leg to the tow hook loop using a
1/2" hex head bolt, 1/2" flat washer, lock washer and nut. Leave loose.
PHOTO 2
Lower Bracket
Spacer
Driver side Bracket installed
DESING QUALITY FODI7.003.E DATE OF REVISION: Date] Page: 1 / 3

EUROGUARD
INSTALLATION INSTRUCTIONS
50394
ONDA CRV 2010 ( LX - EX - EXL )
4. Open the hood and remove the radiator cover pushing out the plastic fasteners. Insert the 5/16" Special bolt in to the slot of the
radiator
support front. in the special bolt insert the spacer tube, then place the upper bracket support and upper bracket, to place the upper bracket
you must introduce it from outside in a grille hole. attach using: ( 1 ) 5/16" flat and lock washer, ( 1 ) 5/16" hex nut. See picture 3 and 4. Repeat
in the opposite side. Leave loose.
PHOTO 3 PHOTO 4
Remove this cover to install upper bracket support and
upper bracket.
Using the special bolt, insert the bolt so the threaded end sticks out. Attach the
spacer bracket, upper bracket support and upper bracket, secure the bolt with a
5/16" flat and lock washers as well as the 5/16" nut.
This slot must be aligned with the
upper bracket support hole.
5. Use the 1/4" bolt guide in the ( 1 ) 1/4 x 3/4" hex head bolt to introduce it in the slot located in the rear side of the radiator support, take out
the bolt guide from the hole of the upper bracket support. See photos 5 and 6. Remove the 1/4" bolt guide and fix using: ( 1 )1/4" Flat washer, (
1 ) 1/4" Hex nut. Leave loose. Repeat for the opposite side. NOTE: BE SURE TO SECURE THE BOLT WHEN REMOVING TO BOLT GUIDE
SO IT WILL NOT FALL INTO THE RADIATOR SUPPORT.
PHOTO 5 PHOTO 6
Locate the 1/4" bolt with the bolt guide attached. Thread
the bolt guide through this slotted hole in the upper
radiator
support and pull through the hole shown in Photo 6.
Remove the bolt guide and secure with a 1/4" flat
washer
and a 1/4" hex nut. Leave loose. NOTE: WHEN
REMOVING THE BOLT GUIDE, DO NOT LET THE BOLT
FALL BACK DOWN INTO THE RADIATOR SUPPORT.
Bolt guide use:
1/4" Bolt guide.
1/4 x 3/4" Hex head bolt.
Once installed into the
radiator
support, remove the bolt guide
holding the threaded portion.
DO
NOT LET THE BOLT FALL BACK
INTO THE RADIATOR SUPPORT.
DESING QUALITY FODI7.003.E DATE OF REVISION: Date] Page: 2 / 3

EUROGUARD
INSTALLATION INSTRUCTIONS
50394
ONDA CRV 2010 ( LX - EX - EXL )
6. Install the upper bracket B in the upper bracket A and attach with: ( 1 ) 3/8 x 1 1/4" carriage head bolt, ( 1 ) 3/8" flat and lock washer, ( 1 )
3/8" hex nut. Leave loose. Repeat for the opposite side. Mount the Euroguard to lower brackets fix with: ( 2 ) 1/2 x 1 1/4" carriage head bolt, ( 2
) 1/2" flat washer, ( 2 ) 1/2" lock nuts. To each side. Leave loose.
7. Modular version only: Attach the upper bracket to the euroguard plate using the lower bolt hole. This same bolt attaches the brushguard
grille to the euroguard plate.
8. For the one piece version: Attach the upper bracket to the euroguard plate using the lower bolt that attaches the brushguard grille to the
euroguard plate.
PHOTO 7 PHOTO 8
Support of upper bracket A.
Upper bracket b.
Upper bracket A. Upper bracket A installed.
9. Make any final adjustment and tighten all hardware.
10. Re-install the radiator cover using the plastic fasteners previously removed. In the holes where the plastic fasteners were replaced, attach
using a 1/4" flat washer with a 1/4" hex nut. See Photo 8.
11. Periodically check and re-tighten bolts as necessary over the term of use.
12. Fill out included warranty card and place in the vehicle.
PHOTO 9 PHOTO 10
NOTA: If necessary to make a cut in the cover of the
radiator in this section so that it does not interfere with
the installation of upper brackets.
EUROGUARD INSTALLED.
DESING QUALITY FODI7.003.E DATE OF REVISION: Date] Page: 3 / 3