EuroLite 50531150 User manual

USER MANUAL
EN
No. 50531155 Receiver
Wireless remote control for single- and multi-colored LEDs 12-24 V
LED Strip RGB/CW/WW Zone RF Controller
No. 50531150 Set (receiver and remote control)
www.eurolite.de
1
•
EN
Thank you for purchasing this LED control system. The 5-channel wireless
receiver is especially designed for control of single- and multi-colored
(C + , RGB, RGB ) LED strips requiring an operating voltage of 12 V and
24 V direct current. The receiver is operated by wireless control (2.4 GHz) via
the remote control. 4 control zones are available. Multiple receivers can be
assigned to the zones as desired and controlled via the same remote control,
either separately or in groups. As the receivers forward the radio signal, a large
range can be covered and all color settings run in sync. The maximum power
consumption of a channel must not exceed 4 A and of all LEDs connected 20 A.
The connection must be made by skilled personnel only. Please read these
operating instructions carefully before using the product. They contain
important information for the correct use of your product. Please keep them for
future reference.
SAFETY INSTRUCTIONS
• Only use the product according to the instructions given herein. Damages due to
failure to follow these operating instructions will void the warranty! e do not assume
any liability for any resulting damage.
• e do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the
warranty/guarantee will be null and void.
• Unauthorized rebuilds or modifications of the product are not permitted for reasons of
safety and render the warranty invalid.
• This product is not a toy. Keep it out of the reach of children. Do not leave packaging
material lying around carelessly.
• Keep this device away from rain and moisture. Indoor use only.
• Protect the product against excessive humidity and heat. The recommended
temperature is -5 to +45°C.
• Before taking into operation, check upon possible damages. If defective, the product
must not be taken into operation.
• This product is maintenance-free, except for occasional cleaning. You can use a
slightly dampened cloth for cleaning. Never use alcohol or solvents.
• Maintenance and service operations are only to be carried out by authorized dealers.

PROTECTING THE ENVIRONMENT
2
•
EN
Disposal of old equipment
hen to be definitively put out of operation, take the product to a local recycling
plant for a disposal which is not harmful to the environment. Devices marked with
this symbol must not be disposed of as household waste. Contact your retailer or
local authorities for more information. Remove any inserted batteries and dispose
of them separately from the product.
You as the end user are required by law (Battery Ordinance) to return all used
batteries/ rechargeable batteries. Disposing of them in the household waste is
prohibited. You may return your used batteries free of charge to collection points in
your municipality and anywhere where batteries/rechargeable batteries are sold.
By disposing of used devices and batteries correctly, you contribute to the
protection of the environment.
Receiver setup
• Install the receiver in a suitable spot and remove the covers from the terminals.
• Connect the LEDs to the negative and positive OUTPUT terminals (V+ = common positive pole,
= negative pole for the warm white LEDs, C = negative pole for the cold white
LEDs,
B = negative pole for the blue LEDs, G = negative pole for the green LEDs, R = negative pole for
the red LEDs.
• The load by the LEDs must not exceed 4 A per channel. The overall load must not exceed 20 A
to avoid damage to the receiver.
• For power supply, connect a regulated power supply unit (min. 12 V, max. 24 V) to the negative
and positive INPUT terminals.
• Screw on the covers with the screws provided.
• For operation the receiver needs to be assigned to the remote control (see chapter “ ireless
Connection” on page 4).
INSTALLATION

INSTALLATION
3
•
EN
Remote control setup
A wall holder and accessories are supplied with the remote control. Either mount the holder to the
wall using the adhesive strip or the screws and dowels.
Inserting batteries into the remote control
For power supply of the remote control, insert two 1.5 V AAA batteries into the battery
compartment as indicated. If the remote is not used for a longer period, please remove the
batteries to prevent damage in case of battery leakage.

WIRELESS CONNECTION
4
•
EN
For the remote control to work together with the receiver, the two devices first have to be paired.
There are four separate control zones. Multiple receivers can be assigned to the four zones as
desired and controlled with a mutual remote control. The receivers can be operated in different
modes so it is possible to operate each zone with different LED types. The functions of the
remote control change according to the set operating mode of the respective receiver.
If multiple receivers are used in the same control zone, the receivers exchange signals among
each other. As a result, all dynamic and static color settings run in sync and there is no visible
difference to a wired system.
Please note:
1) The devices are not paired by default. Each remote control has its own code. To avoid
interferences during operation, the devices need to be paired manually during installation.
2) The receiver can be assigned to only one code at a time and needs to be reset to factory
settings before a new code can be assigned.
3) As the receiver has to be switched on for assigning a code, multiple devices can be
configured simultaneously. In this case, we recommend separately switchable sockets for
different areas of the installation so that certain areas can remain switched off during the
configuration process.
remote control (20 meters)
receiver (10 meters)

WIRELESS CONNECTION
5
•
EN
Pairing the remote control with the receiver
hen paired, the receiver can be controlled via the remote control.
Step Procedure Remarks
1 Connect the LEDs and switch on the
receiver.
1) If the receiver has been paired before,
it has to be reset to factory settings
before it can be paired again.
2) Provided that they are within the range
of the remote control, multiple
receivers can be configured
simultaneously.
2 Select a control zone.
Select the desired control zone using the
ZONE button on the remote control. The
respective indicator lights.
3
Keep the ON button pressed for 5
seconds to switch to pairing mode. The
RF indicator now flashes rapidly.
The pairing process is automatically
terminated after 60 seconds or by
pressing any button.
4 The connected LEDs flash three times
and then return to their previous state.
The devices have been paired
successfully.
Resetting the receiver
After being reset to factory settings, the receiver can be paired with a new remote control.
Step Procedure Remarks
1 Connect the LEDs and switch on the
receiver.
1) The receiver should be reset within 60
seconds after power on.
2) Provided that they are within the
range of the remote control, multiple
receivers can be configured
simultaneously.
2
Keep the OFF button pressed for 10
seconds to initiate the resetting
process. The RF indicator now flashes
rapidly.
1) It is not necessary to select a certain
control zone.
2) The resetting process is automatically
terminated after 60 seconds or by
pressing any button.
3) Any remote control can be used to
reset the receiver.
3 The connected LEDs flash three times
and then return to their previous state.
The receiver has been reset to factory
settings successfully.

WIRELESS CONNECTION
6
•
EN
Pairing multiple remote controls
Each remote control is delivered with its own code preconfigured. If you use multiple remote
controls, the code of one remote control needs to be copied to the other remote controls for
them to operate in sync successfully.
Step Procedure Remarks
1
Keep the ON button on the master
remote control pressed for 5 seconds to
switch to copying mode. The RF indicator
now flashes rapidly.
The copying process is automatically
terminated after 60 seconds or by
pressing any button.
2
Take the remote control you wish to copy
the code to and keep the M(ODE) button
pressed for 5 seconds. The RF indicator
switches from 100% brightness to 0%
and flashes. The copying mode has been
activated.
The copying process is automatically
terminated after 30 seconds or after the
code has been copied successfully.
3
The RF indicator on the remote control
the code has been copied to flashes
three times.
The code has been successfully copied
to the new remote control. The device
now automatically quits the copying
mode.
Copying the code from receiver to remote control
Codes can also be copied from a receiver to a remote control, e.g. if the previously used remote
control was lost and needs to be replaced.
Step Procedure Remarks
1 Switch off the receiver.
2
Keep the M(ODE) button on the remote
control pressed for 5 seconds. The RF
indicator switches from 100% brightness
to 0% and flashes. The copying mode
has been activated.
The copying process is automatically
terminated after 30 seconds or after the
code has been copied successfully.
3 Switch on the receiver. The RF indicator
on the remote control flashes three times.
The code has been successfully copied
to the new remote control. The device
now automatically quits the copying
mode.
Notes:
1) The distance between receiver and remote control should not exceed 2 meters during this
procedure.
2) During the copying process, all information of the entire system is being transmitted. It is not
necessary to repeat the procedure for different control zones.
Resetting the remote control
The remote control can be reset to factory settings.
Step Procedure Remarks
1 Keep the M(ODE) button pressed for 20
seconds.
The RF indicator is dimmed down and
flashes while the M(ODE) button is
pressed. After releasing the button, the
indicator lights with 100% brightness
again, indicating that the resetting
process has been activated.
2 Confirm with OFF button. The RF
indicator flashes three times.
The remote control has been reset to
factory settings successfully.

OPERATION
7
•
EN
Remote Control
Button Function
No function
RGB channels on
RGB channels off
Color ring
Color selection (64 colors available)
Mode selection (9 modes available, see table below)
hite light on/off
Increase warm white light (keep button pressed to proceed quicker)
Increase cold white light (keep button pressed to proceed quicker)
Reduce brightness (keep button pressed to proceed quicker)
Increase brightness (keep button pressed to proceed quicker)
Reduce speed for dynamic programs in 100 levels
(keep button pressed to proceed quicker)
Increase speed for dynamic programs in 100 levels
(keep button pressed to proceed quicker)
Select zones 1-
4 (status indicator lights),
keep pressed for 2 seconds to select all zones (all status indicators light)
Mode Function Remarks Mode Function Remarks
1 Pulsating white
Speed
adjustable,
brightness not
adjustable
6 7 colors fade
Speed
adjustable,
brightness not
adjustable
2 Flashing white 7 Fade R/G
3 3 colors change 8 Fade R/B
4 7 colors change 9 Fade G/B
5 3 colors fade
RF signal indicator
RGB on
Mode (9)
Cold white +
Brightness +
Speed +
Zone indicators
SET
RGB off
Color ring
hite on/off
arm white ‒
Brightness ‒
Speed ‒
Zone selection
(keep pressed for 2 seconds for
all zones)

TECHNICAL SPECIFICATIONS
8
•
EN
Remote control
Carrier frequency: 2.4 GHz
Range: approx. 20 m
Battery: 2 x 1,5V AAA LR03
Standby current: <18 µA
Operating current: <25 mA
Dimensions (Lx xH): 150 x 40 x 20 mm
eight: 95 g
Receiver
Power supply: 12-24 V DC
Standby current: <1
Output power: max. <240 (12 V), <576 (24 V)
Load: max. 4 A per channel (20 A overall load)/
max. 48 (12 V) per channel,
max. 96 (24 V) per channel
Channel count: 5
Gray scale: 1024 levels
Protective circuit: Short circuit
P M frequency: 1000 Hz
Dimensions (Lx xH): 160 x 46 x 25 cm
eight: 100 g
All information is subject to change without prior notice.
Steinigke Showtechnic GmbH • Andreas-Bauer-Str. 5 • 97297 Wa dbütte brunn, Germany
D00129056 Version 1.0 Pub . 26/03/2020