Event Lighting KONTROL5W User manual

KONTROL5W
Battery Powered WDMX Controller
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0

www.event-lighting.com.au
1
Safety Instructions
Warning
• Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
• Do not operate this device outdoors where excessive dust, heat, water, or humidity may
affect it.
• Do not operate this device if the housing or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• Do not operate this device at temperatures higher than 40°C (104°F).
• Only connect this device to a grounded and protected circuit.
• Only use the hanging bracket to carry this device.
• Stop using this device immediately if a serious operating problem becomes apparent.

www.event-lighting.com.au
2
Overview
1. Power switch
2. Charging indicator
a. Red – charging.
b. White – fully charged.
3. Display
4. Wireless DMX indicator light
5. Menu Control buttons
a. [Up] – Enter control menu, jump to the top.
b. [Down] – Enter control menu, skip to next item
c. [Right] – Move through menu pages, go to the next menu level.
d. [Left] – Move through menu pages, go to the previous menu level.
e. [O/Enter] – Change the wireless signal ID number (1 to 7)

www.event-lighting.com.au
3
Display
Menu
Menu
Main
Display
Function
Description
1
Effects
ID (0-7)
Press [Up] or [Down] to select
chase ID.
Play Chase
Play selected chase.
Edit Chase
1. "---" denotes total number
of steps.
2. "|" denotes the channel
value pages
3. "nnn" denotes channel
value
4. Press [Down] to increase
the channel value
5. Press [Right] to save the
current step
6. Press [Left] to delete tehe
current step and move to
previous step
7. Press [Up] to save all and
exit editing
Delete Chase
Delete selected chase
2
Settings
DMX
Setting
DMX Address
Set DMX start address for
controller
Wireless
Wireless
EN
On/Off
Toggle Wireless DMX
Wireless
LED
On/Off
Toggle Wireless DMX
indicator light

www.event-lighting.com.au
4
Power Up
Preset
Program
ID (0-8)
Select ID when starting up
controller, NR8 is Manual
Display
Screen
Mode
DMX630/ON/OFF
Screen mode when controller
is not being used
Screen
Time
3-255
Time to wait before turning off
screen (seconds)
Password
Password (Off/On)
Toggle password
Set Password
Select password for the
controller
Time
Time
Enter the current time
Power On: Timed turn on
Turn on and start selected
program at selected time
Power Off: Timed turn off
Turn off at the selected time
Calibration
Battery
3.762V
Calibrate battery voltage
Fader
4095
Calibrate fader values
Load factory
[Left] - Cancel
Reset to factory defaults
[Enter] - Reset
3
Status
Battery Voltage
Current battery voltage
Version
Software version - JAY102021
Manual Control
1. Set the fixture’s address by entering the menu and going to Settings > DMX Setting.
2. The status will be shown on the display. Use channel 1/6 to select the channel value.
Create a Chase
1. Enter the menu and select Edit Program > ID to choose the program to edit.
2. Select Edit Chase:
a. "---" denotes total number of steps.
b. "|" denotes the channel value pages
c. "nnn" denotes channel value
d. Press [Down] to increase the channel value
e. Press [Right] to save the current step
f. Press [Left] to delete tehe current step and move to previous step
g. Press [Up] to save all and exit editing
Play Chase
1. Press [Enter]
2. Select Effects and confirm with [Enter]
3. Select ID and confirm with [Enter]
4. Select the chase ID to play with [Up] or [Down] and confirm with [Enter]
5. Select Play Chase and confirm with [Enter]
6. Select chase speed with the Speed fader
7. Select fade time between each step with the Fade fader.

www.event-lighting.com.au
5
Time on/off
KONTROL5W can activate or deactivate a chase at a selected time. When using this function,
leave the controller on.
1. Press [Enter]
2. Select Settings and confirm with [Enter]
3. Select ID and confirm with [Enter]
4. Select the chase ID to play with [Up] or [Down] and confirm with [Enter]
5. Select Time and confirm with [Enter]
6. Enter the current time under Time
7. Enter a time under Power On to start the selected program at that time.
8. Enter a time under Power Off to stop the selected program at that time.
To ensure long term optimal battery life, we recommend setting Power Off Bat at no lower than
10%. The controller will turn off when reaching the set percentage.
Password
1. Press [Enter]
2. Select Settings and confirm with [Enter]
3. Select Password and select On or Off with [Right] button
4. Enter the default password, [Up][Down][Up][Down]
5. Set a new password using the [Up], [Down], [Left], [Right] keys
Wireless Pairing
1. Check the colour of the fixture to be controlled.
2. Press the [O] button to switch the wireless signal ID. The WDMX light will change colour
to correspond with the current mode. When the colour is the same as the colour on the
fixture, the WDMX light will flash red to indicate it is sending a wireless signal.
Technical Specifications
• Charging voltage: 5V, 1-3A
• Battery: 2600 mAh
• DMX Channels: max. 30
• Wireless DMX Frequency: 2.4 GHz
• Dimensions: 130x150x40 mm
• Weight: 0.5 kg