EverFocus NeVio EDN850H User manual

EDN850H
Installation Guide
Copyright © EverFocus Electronics Corp.
Release: Jun. 2009 Ver. A

EDN850H
2
This installation guide provides instructions for installing the EDN850H IP Camera.
For all other aspects of using this product, please refer to EDN850H User’s Manual,
which is available on the CD included in this package.
Installation steps
1. Confirm that all of the accessories have been supplied with the network camera
from the list below.
2. Confirm that your PC answers to the minimum computer requirements listed
below.
3. Mount the camera to ceiling or wall. Please see “1. Installation” on page 5.
4. Connect the cables. Please see “2. Connecting the Cables” on page 10.
5. Network Connection. 3 typical types of network connection. Please see “3.
Network Connection” on page 12.
6. Set an IP address. Please see “4. Assign IP address” on page 14.
Package Contents
- Network camera (x1)
- Mounting kit includes:
-Long Screws x 3 (for mounting base)
-Expanding Screws x 3
-Washer x 3
- Circle Installation Sticker x 1
- Desiccant Pack x 1
- Power adaptor (x1)
- Printed Installation Guide (x1)
- Software APs including user’s manual CD (x1)

EDN850H
3
Minimum Computer Requirements
-CPU: PC Pentium IV (2.0 GHz or higher) / AMD Athlon (or higher)
-VGA card: 32 MB min. 16.7 million colours, with DirectX9.0c support
-Memory: 512 MB RAM min., 1 GB HD space or above
Additional HD space depends on required local storage of video files,
100 Mbps network card
-Screen Resolution: 1024 x 768 pixels or higher, 32-bit pixel color resolution
-Operating system: Windows XP, service pack 3 or higher
-Software: DirectX9,0c, Internet Explorer 6.0 or higher
Note: Please connect to Microsoft’s Web Site for downloading.
For example: (This web site may change without notices.)
http://www.microsoft.com/downloads
Interior View of EDN850H
Rotatable cover
Outer Cover ring
Base

EDN850H
4
Reset button
SD card slot
Focus lever
Zoom lever

EDN850H
5
1. Installation
1.1 Mounting Camera
1.1.1 Drill the Holes
1. Paste the drilling template on the ceiling or wall
2. Use the tool to drill 4 holes, 3 for screw A, B and C,
1 for power/video cable.
Installation sticker
Screw hole A
Screw hole B
Screw hole C
Power/Video/Alarm/Audio Cable
Camera base Screw
A,B,C
Outlet hole
Network Cable

EDN850H
6
1.1.2 Mounting
1. Take off camera’s cover.
Loose outer cover ring first
Take off camera’s cover.

EDN850H
7
2. Fix the camera base to ceiling or wall by using 3 screws.
Ceiling Mount:
Wall Mount:

EDN850H
8
1.2 Adjusting Camera
1.2.1 Adjusting Camera Position
Adjust the camera to any angle that you wish. Pan and tilt to aim the camera at what
you need to watch until the best angle of image is obtained.
Adjust the camera to best angle for viewing.
Tilt
Pan

EDN850H
9
NOTE:
1. If necessary, you can put desiccant pack in bracket side. Use cable to fix it before
placing the cover back to camera.
2. To close camera cover, please push the inner cover until it completely covers the
whole red gasket and line up with camera base parallel (The inner cover need to be
aligned with camera base otherwise it cannot be closed). Then close the outer cover
ring tightly to the camera base.
Module can be adjusted up and down
When you install on the ceiling, Change angle of view
by turning this joint

EDN850H
10
2. Connecting the Cables
○
1Network cable: Connect to LAN via this standard RJ-45 connector.
Optional: This socket can also be used to power via PoE (Power over Ethernet)
○
2
Audio cable: For connecting to Audio In/Out device.
Green: Audio Out- it can be connected to an active speaker with a built-in
amplifier or a pair of headphones. A 3.5mm audio connector must be used for the
audio out.
Red: Audio In- 3.5mm stereo socket for line-in signal
○
3
Power 12VDC: Connect with power adaptor.
○
4
Video cable: Loop through connection to the video signal from the Video In
connector. It is terminated with a coaxial/BNC connector.
○
5
Alarm I/O cable: For connecting to Alarm In/Out device.
Purple:Alarm Out+
White:Alarm Out-
Gray:Alarm In
Pink:Alarm GND
○
1
○
2
○
3
○
4
○
5

EDN850H
11
Terminal connector schematic diagram

EDN850H
12
3. Network Connection
This section tells you how to do different types of network connections to IP cameras.
a. Router or LAN connection
This is the most common connection that allows multiples PC to see IP cameras/
video servers in pre-existing LAN through a router.
By doing port forwarding, you can view camera outside of internal LAN on internet.
b. Direct High Speed Connection
Direct High Speed Connection connect camera directly to modem without a router.
You need to assign the IP address you obtain from internet service provider to IP
camera/ Encoder. To access the camera, just type http:// IP address of your internet
provider. If you have a dynamic IP address, this connection does not work for you.

EDN850H
13
c. One to one connection from PC to IP camera
You can connect directly without switch. However, only the PC connecting to camera
can view the IP camera.

EDN850H
14
4. Assign IP Address
Please install IP utility software from CD before you go through the following process.
Please note the following procedures are an example according to EDN850H default
values. These values may vary with your network system. Please consult your ISP or
network administrators for more detail of network setting reference.
IP utility (in supplied CD) is a recommended tool to assign IP address. The default
network setting is DHCP. Once login to EDN850H, you can change TCP/IP setting
for your own environment.
1. Active IP Utility.
2. Click “Find Devices” button.
This helps to automatically obtain the EDN850H network configuration details including
Mac Address, Machine Name, Machine Type, IP Type, Subnet Mask, Gateway Address,
DNS1 Address, and DNS2 Address.
3. The IP address of EDN850H will be automatically detected and shown in the

EDN850H
15
window. Tick the selected EDN850H.
4. If you want to manually change the IP setting,YOU MUST CLICK “LOGIN”.You
will be asked to enter “User ID” and “Password”. This is a security measure of
configuration setting, in order to modify those network configurations of EDN850H.
EDN850H administrator can only do the setting. Therefore only who has admin
authority could modify these settings. The ID & password must be the admin user and
be sent to the device when you click "Set configuration". If the ID and password do
not belong to an admin user, then setting will be discarded.
NOTE: Default User ID is “user1” and default password is “11111111”.

EDN850H
16
5. To change configurations, double click on the value that you wish to make change
and enter the desired new value. After the change is done, press “Set Configuration”
to confirm setting.
Note: Most router support DHCP. However, when you have difficulty of selecting IP
type, please consult your IP administrator for the IP type your router support.

EDN850H
17
6. Click “Connect to selected IP” and the browser will automatically connect to the
EDN850H network page.
7. You will be asked to enter User ID and Password first.
Note: Default user name is “user1” and default password is “11111111”.
8. Now, you will be lead to the live view page of EDN850H.
9. Exit: Close IP Utilitywindow to finish your setting.

EDN850H
18
EverFocus Electronics Corp.
Head Office:
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
USAL.A. Office:
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: [phone]
FAX: [phone]
www.everfocus.com
USAN.Y. Office:
415 Oser Avenue Unit S
Hauppauge, NY 11788
TEL: [phone]
FAX: [phone]
www.everfocus.com
Europe Office:
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: [phone]
FAX: [phone]
www.everfocus.de
China Office:
Room B-05D-1, KESHI PLAZA, Shangdi
Information Industry Base, Haidian District,
Beijing China 100085
TEL: [phone]/38/39
FAX: [phone]
www.everfocus.com.cn
Japan Office:
1809 WBG MARIBU East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
Your EverFocus product is designed and
manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be
disposed of separately from your household
waste.
Please, dispose of this equipment at your local
community waste collection recycling centre.
In the European Union there are separate
collection systems for used electrical and
electronic product.
Please, help us to conserve the environment we
live in!
Ihr EverFocus Produkt wurde entwickelt und
hergestellt mit qualitativ hochwertigen Materialien
und Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und
elektronische Geräte am Ende ihrer Nutzungsdauer
vom Hausmüll getrennt entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei Ihrer örtlichen
kommunalen Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu erhalten, in der
wir leben!
P/N: MEDNG00510_Ver.A